Canon XA10 XA10 Instruction Manual - Page 163

Memory Card and Accessories

Get Canon XA10 PDF manuals and user guides View all Canon XA10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 163 highlights

Troubleshooting Sound is distorted or is recorded at lower levels. - When recording near loud sounds (such as fireworks, shows or concerts), sound may become distorted or it may not be recorded at the actual levels. Adjust the audio recording level manually (0 76). There are brief stops in the sound recorded with the optional WM-V1 Wireless Microphone. - This may occur if the LOCK switch on the Eye-Fi card was set to prevent writing, causing wireless communication to occur while recording. Change the position of the LOCK switch. The picture is displayed correctly but there is no sound from the built-in speaker. - Speaker volume is turned off. Adjust the volume. - If the STV-250N Stereo Video Cable is connected to the camcorder, disconnect it. - The AV terminal is set to headphone output. Set 8 [AV/Headphones] to [AV]. 163 Memory Card and Accessories Cannot insert the memory card. - The memory card was not facing the correct direction. Turn the memory card over and insert it. Cannot record on the memory card. - The memory card is full. Delete some recordings (0 98, 130) to free some space or replace the memory card. - Initialize the memory card (0 40) when you use it with the camcorder for the first time. - The LOCK switch on the memory card is set to prevent accidental erasure. Change the position of the LOCK switch. - A compatible memory card must be used to be able to record movies on a memory card (0 36). - The folder and file numbers have reached their maximum value. Set 8 [Photo Numbering] to [Reset] and insert a new memory card. The wireless controller will not work. - Set 6 [Wireless Remote Control] to [On]. - Replace the battery of the wireless controller. Cannot upload files wirelessly using an Eye-Fi card. - You may have inserted the Eye-Fi card into memory card slot X. Insert it into memory card slot Y. - 6 [Eye-Fi Communication] is set to [Off] (i appears onscreen). Set it to [Automatic]. - Wireless communication is not available in recording mode or while the optional WM-V1 Wireless Microphone is attached to the camcorder. Set the camcorder to playback mode or remove the WM-V1. - Opening the LCD panel may help when the wireless connection is not strong enough. - During wireless transfer, wireless communication may stop when the wireless signal conditions worsen (h appears onscreen). Perform wireless transfer in a place with good signal conditions. - Contact the card manufacturer's customer care. The wireless communication status icon does not appear - You may have inserted the Eye-Fi card into memory card slot X. Insert it into memory card slot Y.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
Troubleshooting
163
Sound is distorted or is recorded at lower levels.
- When recording near loud sounds (such as fireworks, shows or concerts), sound may become
distorted or it may not be recorded at the actual levels. Adjust the audio recording level
manually (
0
76).
There are brief stops in the sound recorded with the optional WM-V1 Wireless Microphone.
- This may occur if the LOCK switch on the Eye-Fi card was set to prevent writing, causing
wireless communication to occur while recording. Change the position of the LOCK switch.
The picture is displayed correctly but there is no sound from the built-in speaker.
- Speaker volume is turned off. Adjust the volume.
- If the STV-250N Stereo Video Cable is connected to the camcorder, disconnect it.
- The AV terminal is set to headphone output. Set
8
[AV/Headphones] to [AV].
Memory Card and Accessories
Cannot insert the memory card.
- The memory card was not facing the correct direction. Turn the memory card over and insert it.
Cannot record on the memory card.
- The memory card is full. Delete some recordings (
0
98, 130) to free some space or replace
the memory card.
- Initialize the memory card (
0
40) when you use it with the camcorder for the first time.
- The LOCK switch on the memory card is set to prevent accidental erasure. Change the position
of the LOCK switch.
- A compatible memory card must be used to be able to record movies on a memory card
(
0
36).
- The folder and file numbers have reached their maximum value. Set
8
[Photo
Numbering] to [Reset] and insert a new memory card.
The wireless controller will not work.
- Set
6
[Wireless Remote Control] to [On].
- Replace the battery of the wireless controller.
Cannot upload files wirelessly using an Eye-Fi card.
- You may have inserted the Eye-Fi card into memory card slot
X
. Insert it into memory card slot
Y
.
-
6
[Eye-Fi Communication] is set to [Off] (
i
appears onscreen). Set it to [Automatic].
- Wireless communication is not available in recording mode or while the optional WM-V1
Wireless Microphone is attached to the camcorder. Set the camcorder to playback mode or
remove the WM-V1.
- Opening the LCD panel may help when the wireless connection is not strong enough.
- During wireless transfer, wireless communication may stop when the wireless signal conditions
worsen (
h
appears onscreen). Perform wireless transfer in a place with good signal
conditions.
- Contact the card manufacturer’s customer care.
The wireless communication status icon does not appear
- You may have inserted the Eye-Fi card into memory card slot
X
. Insert it into memory card slot
Y
.