Canon iP6700D Easy Setup Instructions

2

Prepare the Printer

1

Before turning on the printer, open the cover

and remove the protective material and tape

from the printer as shown.

The tape position

is subject to change. Write down the serial

number located inside the printer. You will

need this to register your products.

CAUTION:

Be sure to remove the protective

material before you turn on the printer.

2

Close the cover. Plug the power cord into the

back of the printer and connect the other end

to a power outlet. Press the

POWER

button.

The printer will initialize. Wait until the

POWER

lamp displays a steady light.

NOTE:

Do not connect the USB cable at this

stage.

3

When the screen shown on the LCD appears,

use the

buttons to select a language

and then press the

OK

button.

NOTE:

• If the language you want to be displayed is not

selected, refer to "An unintended language is

displayed on the LCD" in the Direct Printing

Guide.

• If you leave the printer more than five minutes

without using any button on the operation panel,

the LCD goes into sleep mode automatically.

Press the

OK

button to turn on the LCD again.

4

Pull down the paper output tray. Raise the

cover. Lower the inner cover.

NOTE:

Put your fingers in the notches in either

side of the paper output tray and pull down to

open it.

5

The print head holder automatically moves to

the center.

IMPORTANT:

If the cover is left open for more

than ten minutes, the print head holder

moves to the right. Close and reopen the

cover to return the holder to the center.

Start Here

Easy Setup Instructions

1

Unpack the Printer

1

Carefully remove all items from the box.

PIXMA iP6700D

Photo Printer

Documentation and

Software Kit

PIXMA iP6700D

Print Head

Power Cord

3

Install the Print Head

1

Remove the print head from its package.

CAUTION:

There might be some transparent

or light blue ink on the inside of the bag

the print head comes in, or the inside of the

protective cap. This has no effect on print

quality. Be careful not to get ink on yourself

when handling these items.

2

Remove the orange protective cap from the

print head.

NOTE:

Do not touch the print head nozzles

and the electrical contacts.

3

Firmly raise the print head lock lever until it

stops into place.

4

Slide the print head into the holder.

The print head will rest at a slight angle.

5

Lower the print head lock lever carefully and

press it down.

4

Install the Ink Tanks

1

Peel back the orange tab completely and

remove the plastic wrapper from the Yellow

Ink Tank (CLI-8Y).

2

Twist off and discard the orange protective

cap located on the bottom of the ink tank.

IMPORTANT:

Do not touch the electrical

contacts.

NOTE:

To avoid spilling ink, never press on

the sides of an ink tank. Do not touch the

open ink port once the protective cap is

removed, as this may prevent the ink from

being ejected properly.

3

Insert the yellow ink tank into the right-hand

slot.

Press the

mark on the ink tank until it

clicks into place and then its lamp lights red.

4

Insert the remaining five ink tanks into their

appropriate slots. Ensure that ink tank lamps

light red.

5

Close the inner cover and then the cover.

The message requesting head alignment is

displayed on the LCD. Go to the next step.

NOTE:

• The printer will perform a print head cleaning.

Wait until the

POWER

lamp displays a steady

light before proceeding.

• If the

Alarm

lamp still lights even after the

printer has stopped making operating noises,

an ink tank may not be installed properly. Open

the cover and make sure that the ink tanks are

installed in the correct order directed on the

label.

5

Align the Print Head

1

Lift open the paper support and extend the

paper output tray.

IMPORTANT:

Be sure to close the inner cover

completely, or the paper will not feed properly.

2

Pinch the paper guide and slide it to the left.

Load a few sheets of blank paper into the auto

sheet feeder, align the paper with the right

side of the cover guide, then slide the paper

guide toward the left edge of the paper.

3

Ensure that the message requesting head

alignment is displayed on the LCD, select

Yes

using the

buttons and then press the

OK

button.

The pattern is printed. And the print head is

aligned automatically.

IMPORTANT

: It takes about 4 minutes to finish

printing.

When automatic print head alignment cannot

be executed correctly, the message

"Auto

head align has failed. Press [OK] and repeat

operation. <See manual>"

is displayed on the

LCD.

Refer to "An Error Message is Displayed on the

LCD" in the

Direct Printing Guide

.

Continue with Step 6

on side two.

CLI-8C Cyan

CLI-8BK Black

CLI-8PC Photo Cyan

click

Ink Tanks

CLI-8M Magenta

CLI-8PM Photo Magenta

CLI-8Y Yellow

Cover

Inner cover

Paper output tray

Series

Photo Printer

Protective cap

Paper support

Paper output tray

POWER button

POWER lamp

Tear at notch to open

Electrical

contacts

Print head

nozzles

Paper

guide

Auto sheet

feeder

Print side

Cover guide

Serial number location

Ink tank lamp

Ink port

Electrical contacts

Refer to the color

guide on the print

head lock lever.

Canon iP6700D Easy Setup Instructions

Canon iP6700D - PIXMA Color Inkjet Printer Manual

Canon iP6700D manual content summary: