Canon imageFORMULA DR-S150 User Guide

Canon imageFORMULA DR-S150 Manual

Get Canon imageFORMULA DR-S150 PDF manuals and user guides View all Canon imageFORMULA DR-S150 manuals
Add to My Manuals
Save this manual to your list of manuals

Canon imageFORMULA DR-S150 manual content summary:

  • Canon imageFORMULA DR-S150 | User Guide - Page 1
    User Manual • Please read this manual before operating this scanner. • After you finish reading this manual, store it in a safe place for future reference.
  • Canon imageFORMULA DR-S150 | User Guide - Page 2
    Document Scanner, Model 6130150 / 6130220 NOTE: This equipment has been tested with the instructions, may off and on, the user is encouraged to try unless otherwise specified in the manual. If such changes or Canon U.S.A. Inc. One Canon Park, Melville, NY 11747, U.S.A. Tel. No. 1-800-OK-CANON
  • Canon imageFORMULA DR-S150 | User Guide - Page 3
    and other office equipment. The service. For more information regarding return and recycling of WEEE products, please visit www.canon-europe.com/weee. Model Names The following name may be provided for the safety regulations in each sales region of the Document Scanner. DR-S150: Model 6130150 DR
  • Canon imageFORMULA DR-S150 | User Guide - Page 4
    imageFORMULA is a trademark of CANON displays and in this manual denotes Wi-Fi Protected DOCUMENTS, YOU THE CUSTOMER ARE RESPONSIBLE FOR INSPECTING THE SCANNED IMAGES AND VERIFYING THAT DATA IS INTACT. THE MAXIMUM LIABILITY OF CANON ELECTRONICS INC. UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE
  • Canon imageFORMULA DR-S150 | User Guide - Page 5
    the Scanner Documentation for this scanner consists of the following manuals. ● Product Safety Guide Before using the scanner, be sure to read and follow these instructions. ● Setup Guide This describes setup procedures for the scanner. Read this manual when you first use the scanner. ● User Manual
  • Canon imageFORMULA DR-S150 | User Guide - Page 6
    User Manual (electronic manual) will be registered to the following location. Symbols Used in This Manual The following symbols are used in this manual to explain procedures, restrictions, handling precautions, and instructions performed correctly. To use the scanner safely, always pay attention to
  • Canon imageFORMULA DR-S150 | User Guide - Page 7
    Contents Introduction 5 Symbols Used in This Manual 6 Before Using the Scanner 9 System Requirements of Software 9 Turning the Power ON 10 Turning Off the Power 10 Important Safety Instructions 12 Installation Location 12 AC Adapter 12 Moving the Scanner 13 Handling 13 Disposal 14 When
  • Canon imageFORMULA DR-S150 | User Guide - Page 8
    Glass and the Rollers 107 Replacing Consumable Parts 110 Removing the Document Feed Tray 114 About the Canon imageFORMULA Driver Setting Tool ..... 114 Troubleshooting 116 Common Problems and Solutions 116 Software Troubleshooting 121 Useful Tips 122 Clearing a Paper Jam 124 Error Message
  • Canon imageFORMULA DR-S150 | User Guide - Page 9
    as of June 2020. For the latest software support information, go to the Products page on the Canon website. Other requirements • An ISIS-compatible application or of the computer and the environment. • The scanner drivers provided with the scanner do not necessarily operate on all ISIS or TWAIN
  • Canon imageFORMULA DR-S150 | User Guide - Page 10
    on the taskbar as follows. Power button If the taskbar icon appears as , the scanner is not properly connected to the computer. Check the status of the power switch and the touch panel, or place a document in the document feed tray. When you press and hold the power button two seconds or longer,
  • Canon imageFORMULA DR-S150 | User Guide - Page 11
    an extended period, turn off the power and disconnect the power cord from the AC outlet for safety. Hint The scanner's auto power off setting is enabled by default, and the scanner will turn off automatically if it is not operated for 4 hours. For details on how to disable this setting, see
  • Canon imageFORMULA DR-S150 | User Guide - Page 12
    ● Do not use an AC adapter other than the one provided with the scanner. Do not use the AC adapter provided with the scanner with other products. ● If you have any questions regarding the power supply, contact your local authorized Canon dealer or service representative for further information. 12
  • Canon imageFORMULA DR-S150 | User Guide - Page 13
    turn OFF the power, and disconnect the power plug from the power outlet. Then, contact your local authorized Canon dealer or service representative to have the unit serviced. ● Before moving the scanner, be sure to turn OFF the power, and disconnect the power plug from the power outlet CAUTION ● Do
  • Canon imageFORMULA DR-S150 | User Guide - Page 14
    water or flammable substances (alcohol, paint thinner, benzene, etc.) to spill into the scanner, as this may result in a fire or electric shock. Doing so might cause 2.4 GHz frequency band (2.400 to 2.4835 GHz). Other users of these frequencies include products such as microwave ovens, scientific
  • Canon imageFORMULA DR-S150 | User Guide - Page 15
    ). After stopping, consult with your retailer or with our sales staff regarding measures to avoid interference (e.g., partitioned installation). 3. Otherwise, if troubles occur from radio frequency interference by this device to other stations, consult with your retailer or our sales staff. 15
  • Canon imageFORMULA DR-S150 | User Guide - Page 16
    in the following list, contact customer service. Version Name Product Code DR-S150 100V 4044C001 DR-S150 100V + Feeder Tray w/ NFC 4044C013 reader DR-S150 120V 4044C002 DR-S150 120V + Feeder Tray w/ NFC 4044C014 reader DR-S150 220-240V 4044C003 DR-S150 220-240V + Feeder Tray w/ 4044C015
  • Canon imageFORMULA DR-S150 | User Guide - Page 17
    possible. ● Wide variety of Connection Modes Connections by USB, wired LAN (DR-S150 only), or wireless LAN are available to support your operating environment. Supported USB formats include USB 3.2 Gen 1x1/USB 2.0. ● Compact Design The scanner has a compact size of 291 mm (11.5") (W) × 600 mm (23
  • Canon imageFORMULA DR-S150 | User Guide - Page 18
    p. 40) ● Double feed detection by length The scanner stops feeding when a double feed is detected by comparing document page lengths. "Detecting a document double feed" (See p. 40) * Based on the length of the first document page, the scanner detects a double feed when fed a different-length page
  • Canon imageFORMULA DR-S150 | User Guide - Page 19
    Scans passports using the separately sold carrier sheet (for passports) ● COT Admin (DR-S150 only) This is a server application that can be used for centralized management of jobs/scanners/users. This enables the scanner's touch panel to be used for user authentication and logging on using NFC. 19
  • Canon imageFORMULA DR-S150 | User Guide - Page 20
    on the scanner status. Power Button Indication Lit Flashing (slowly) Flashing (quickly) Description Power is on Sleep mode An error (paper jam, front unit is open, double feed, etc.) has occurred C Document Feed Tray Place the document. D Document Guides Align the document guides with both
  • Canon imageFORMULA DR-S150 | User Guide - Page 21
    Front View (With the Document Eject Tray Open) X Z Y [ \ A Feed Extension Support Open this when placing long paper in the scanner. B Feed Support Pull this out to support loaded documents. C Touch Panel You can touch the screen to operate the scanner's various functions. D Feed Selection Lever
  • Canon imageFORMULA DR-S150 | User Guide - Page 22
    Back View DR-S150 DR-S130 1 2 3 4 5 A LAN Connector Connect a network cable that supports RJ-45 (10Base-T/100BaseTX/1000Base-T). B USB Connector Connect the supplied USB cable to this connector. C Connector for Options This can be used if you purchase
  • Canon imageFORMULA DR-S150 | User Guide - Page 23
    connected via USB When connected via wired LAN (DR-S150 only) When connected via Wi-Fi C Shared Folder Button Use a job on the scanner to scan documents. (See p. 65) D CaptureOnTouch Button Use a job in CaptureOnTouch to scan documents. (See p. 64) E Settings Button Displays the settings menus
  • Canon imageFORMULA DR-S150 | User Guide - Page 24
    is required when the scanner is turned on. PIN function can be enabled or disabled using the Web menu. "PIN Setting" (See p. 104)  Authentication Screen (DR-S150 only) This may be displayed when the COT Admin mode is enabled. To use this function, the optional Document Feed Tray with NFC Reader
  • Canon imageFORMULA DR-S150 | User Guide - Page 25
    name. C Password Enter a password. D Login Button Log in on the scanner. E NFC Certification Screen Button Displays the NFC Certification screen. Admin User Login screen   A Password Enter a password. B OK Button Log in on the scanner as an administrator. The administrator password is the same as
  • Canon imageFORMULA DR-S150 | User Guide - Page 26
    exceeding 356 mm (14") size are fed one sheet at a time. • Scanning documents before the ink is dry can cause problems with the scanner. Always make sure that the ink on a document is dry before scanning it. • Scanning documents that are written in pencil or similar material may make the rollers and
  • Canon imageFORMULA DR-S150 | User Guide - Page 27
    There are clips or staples. Extremely thin document such as semi-transparent thin paper. Documents with excessive paper dust particles. Business Card Size Detect by Ultrasonic] check box in the [Error Detection] tab on the scanner driver settings screen. (See p. 40) Passport Size: 88 mm x 125 mm
  • Canon imageFORMULA DR-S150 | User Guide - Page 28
    the various lengths. 2 Pull out the feed support. Open the feed extension support when placing long documents. The document eject tray can be adjusted to 3 lengths. Pull out the document eject tray according to the length of the document. Also, erect the document eject stopper on the front edge if
  • Canon imageFORMULA DR-S150 | User Guide - Page 29
    3 Set the feed selection lever to Normal mode. 5 Place the document. 4 Adjust the document guides to fit the width of the document to be scanned. 6 Align the document guides with both edges of the document. IMPORTANT • When placing documents into the feed tray, take care not to cut your hand on
  • Canon imageFORMULA DR-S150 | User Guide - Page 30
    before placing them into the feeder. If the leading edge of a document is curled, it may cause a paper jam. • If feeding stops due to a system error or paper jam while the scanner is scanning, resolve the problem, make sure that the scanned image of the last page that was successfully fed has
  • Canon imageFORMULA DR-S150 | User Guide - Page 31
    that get jammed may be damaged when you remove them. 2 Adjust the document guides to fit the width of the card to be scanned. • When scanning cards, clear the [Detect by Ultrasonic] check box in the [Error Detection] tab on the scanner driver settings screen. (See p. 40) Hint Up to 3 cards can be
  • Canon imageFORMULA DR-S150 | User Guide - Page 32
    document with the folded edge facing right and the top edge facing downward. IMPORTANT Adjust the document guides to fit the width of the document. A2-sized documents. When scanning a folded document of a size other than the standard formats, set [Page Size] on the scanner driver settings screen
  • Canon imageFORMULA DR-S150 | User Guide - Page 33
    [Basic] tab to a size that is half that of the paper to be actually scanned, and set [Scanning Side] to [Folio]. For example, when scanning a document of A3 size folded, set [Page Size] to [A4]. 1 Open the scanner driver settings screen. (See p. 72) 2 Set the [Page Size] to half the size of the
  • Canon imageFORMULA DR-S150 | User Guide - Page 34
    sure to set the Feed Selection Lever to Bypass Mode. After placing the document, align the document guides with both edges of the document. CAUTION If the document is not placed properly inside the carrier sheet, you may get a document jam or not get a scan image as intended. IMPORTANT • Insert
  • Canon imageFORMULA DR-S150 | User Guide - Page 35
    problems such as paper jam. • As a rough guide, replace the carrier sheet after 1,000 scanning operations with a single 80g/m2 (22 lb bond) sheet inserted. Carrier sheet is a consumable item. Replace it with a new one when necessary, if there is visible damage or smudging. 1 Open the scanner driver
  • Canon imageFORMULA DR-S150 | User Guide - Page 36
    document guides with both edges of the document. CAUTION • If the carrier sheet or passport is not loaded properly, you may get a document jam or not get a scan image as intended. • When scanning passports, clear the [Detect by Ultrasonic] check box in the [Error Detection] tab on the scanner driver
  • Canon imageFORMULA DR-S150 | User Guide - Page 37
    dpi or less on the scanner driver settings screen.(See p. 73) • The maximum thickness that can be scanned is 4 mm with the passport inserted inside the carrier sheet. If the thickness exceeds 4 mm, the scanner may break down due to problems such as paper jam. • Documents other than passports should
  • Canon imageFORMULA DR-S150 | User Guide - Page 38
    normally 356 mm (14"), but you can scan documents up to 3,000 mm (118.1") long by setting the scanner to the Long Document mode. IMPORTANT By selecting the Long Document mode and setting the [Page Size] on the scanner driver settings screen to Auto-detection, documents of up to 3,000 mm (118.1") in
  • Canon imageFORMULA DR-S150 | User Guide - Page 39
    screen. Hint When you set the Long mode, [(Long Document)] will be displayed in [Page Size] in the [Basic] tab. 1 Open the scanner driver settings screen. (See p. 72) 2 Click to display the [Scanner Information] dialog box. The [Scanner Information] dialog box appears. 3 Click [Maintenance]. The
  • Canon imageFORMULA DR-S150 | User Guide - Page 40
    whether to save the scanned image after scanning has finished and continue scanning the document (double feed detection ignore function). To use the double feed detection function, you must first open the scanner driver settings screen and enable double feed detection. It is also necessary to set
  • Canon imageFORMULA DR-S150 | User Guide - Page 41
    by Length], and [Detect by Ultrasonic and Length]. 3 Click the [More] button when the Double Feed Detection Ignore function is also used. The scanner driver's Detail Settings screen opens. 4 Select the [Rapid recovery system] check box. 4 To use the double feed detection ignore function, open the
  • Canon imageFORMULA DR-S150 | User Guide - Page 42
    double feed is detected When not using the double feed detection ignore function If a document double feed is detected during scanning, document feeding stops when the double fed documents are ejected. When this happens, the following error is displayed in the touch panel. 䣕䣖䣑䣒 Also
  • Canon imageFORMULA DR-S150 | User Guide - Page 43
    Buttons of [Rapid Recovery System] Screen [SAVE & CONTINUE] [STOP] [DISCARD & CONTINUE] Description Saves the preview image as a scanned image and scans the rest of the document. Discards the preview image and stops scanning. Discards the preview image and continues scanning. Place the double fed
  • Canon imageFORMULA DR-S150 | User Guide - Page 44
    Operating the Settings Menus About the Settings Menus The setting menus are functions that allows users to change some of the scanner's functions. Procedure to operate the settings menu Use the following procedure to operate the settings menus. 1 On the home screen of the touch panel, tap
  • Canon imageFORMULA DR-S150 | User Guide - Page 45
    Settings Available Network Default Gateway - WPS - Wi-Fi Setting Manual - Wireless Connection - Tool COT Enable* - - Admin IP Connection Address* - - Setting* SSL* - - Scan Setting Detect Double Feed - - - * DR-S150 only 3 Tap the various items to confirm and change
  • Canon imageFORMULA DR-S150 | User Guide - Page 46
    was turned on. Tap [Reset] to reset the current number of sheets scanned. System Information Shows the following system information for the scanner. • OS Version • Firmware Version • Kernel Version • Scanner Name • Serial Number • Wired MAC Address (DR-S150 only) • Wireless MAC Address • SSID 46
  • Canon imageFORMULA DR-S150 | User Guide - Page 47
    and computer are connected. Connect with USB cable: The scanner and computer are connected via USB cable. Connect with Ethernet cable (DR-S150 only): The scanner and computer are connected via LAN cable. Connect via Wi-Fi: The scanner and computer are connected via Wi-Fi. By setting the
  • Canon imageFORMULA DR-S150 | User Guide - Page 48
    is successful, the [Wi-Fi Setting] screen appears. Manual Manually type in the SSID and security key for the appears. COT Admin Connection Setting (DR-S150 only) Select the following menu items OK button after enabling [Enable], the scanner restarts automatically and the connection mode switches
  • Canon imageFORMULA DR-S150 | User Guide - Page 49
    Connection Test Test the connection with COT Admin. Scan Setting Select the following of documents, and detecting unevenness between documents by ultrasonic sensors, which can be set by the scanner driver. This setting disables the Double Feed Detection function enabled in the scanner driver
  • Canon imageFORMULA DR-S150 | User Guide - Page 50
    that can be used when you want to register the scan settings and output method settings in the scanner. You can scan the document and save the scanned data by operating the scanner, without having to operate a computer. The application is available on both smart devices and computers. IMPORTANT • If
  • Canon imageFORMULA DR-S150 | User Guide - Page 51
    smart devices For computers Registering a job in the scanner and scanning from the scanner touch panel If you copy the registered job to the scanner, the job can be recalled from the scanner touch panel. Once the job is registered, you can scan documents without using a computer or a smart device
  • Canon imageFORMULA DR-S150 | User Guide - Page 52
    Basic Operations: Various Scanning Operations Using a Computer (CaptureOnTouch) Starting and Exiting CaptureOnTouch By default, CaptureOnTouch becomes resident in the system when you start your computer. Double-click in the taskbar to start CaptureOnTouch and display the main window. Hint You can
  • Canon imageFORMULA DR-S150 | User Guide - Page 53
    Hint In Windows 8.1, it is registered in the following location. Selecting a scanner The following is an explanation of how to select a scanner using CaptureOnTouch. 1 Click the (CaptureOnTouch Icon) on the taskbar. 2 Click [Select Scanner] on the menu. • Open [GO] - [Applications] folder from the
  • Canon imageFORMULA DR-S150 | User Guide - Page 54
    not appear, reinstall the scanner driver. 1 Click (CaptureOnTouch Icon) in the menu bar and then click [Select Scanner] from the menu which the top right of the main window to move between sections. 2 Select the scanner you are using and click [OK]. Various panels have been prepared according to
  • Canon imageFORMULA DR-S150 | User Guide - Page 55
    panel -> Selecting the Select output panel -> Start scanning 1 Place the document in the scanner. 2 Click the select document panel for the document to be scanned from [1 Select document]. The selected [Select document] panel will be displayed in orange. 3 Click the output panel for the scan
  • Canon imageFORMULA DR-S150 | User Guide - Page 56
    scanning is in progress, the number of pages scanned is displayed in addition to the scanner settings. When the scan is finished, the [Scanned image preview screen] opens. Hint If using the same document selection and output combination the next time, click the [Save to Shortcut] button. The Select
  • Canon imageFORMULA DR-S150 | User Guide - Page 57
    shortcuts that combine frequently-used document selections and outputs, you can scan just by clicking the Scanning Shortcut panel. Hint If a registered scanning shortcut is assigned as a job, you can run shortcut scans using these settings by operating the scanner touch panel. Click the button
  • Canon imageFORMULA DR-S150 | User Guide - Page 58
    shortcut panel will be created. 2 The Edit Scanning Shortcut Panel dialog box appears when you click the Edit button. 3 Click the [Document] tab to set the Select document settings. Hint You can also create a new Destination panel by clicking on the [New shortcut] button, and in the menu that
  • Canon imageFORMULA DR-S150 | User Guide - Page 59
    4 Click the [Batch separation] tab to set the batch separation. 5 Click the [Output] tab to set the outputs. 59
  • Canon imageFORMULA DR-S150 | User Guide - Page 60
    6 Click the [Index] tab to set the index file. 7 Click the [Option] tab to set the options. [Edit after scanning] Check it on to enable modifying the scanned images in Scan Editing screen. When unchecked, the Edit window is not displayed in Scan Editing screen. [Enable additional scan] Check it on
  • Canon imageFORMULA DR-S150 | User Guide - Page 61
    [Job assignment] You can assign a scanning shortcut as a job. When a scanning shortcut is assigned as a job, an icon for the assigned job No. will be displayed in the scanning shortcuts panel. 8 Click the [General] tab to make other settings. [Order of output] You can add or delete the output, and
  • Canon imageFORMULA DR-S150 | User Guide - Page 62
    the scanning shortcut settings, the [Scan more pages] button will not be displayed. The document is scanned. While scanning is in progress, the number of pages scanned is displayed in addition to the scanner settings. When the scan is finished, the [Scanned image preview screen] opens. CAUTION • If
  • Canon imageFORMULA DR-S150 | User Guide - Page 63
    3 To check the scanned image, click the [Finish] button. Hint If you click [Open storage folder], the folder in which the saved scanned images were saved opens. Depending on the output settings, the [Open storage folder] link may not be displayed. Hint If [Edit after scanning] is disabled in the
  • Canon imageFORMULA DR-S150 | User Guide - Page 64
    during scanning, and completion popup windows are displayed. • If the [Do not display the main screen when the scan is started with the scanner button] checkbox is enabled in the Environmental settings, [Enable additional scan] and [Edit after scanning] will be disabled when scanning is started from
  • Canon imageFORMULA DR-S150 | User Guide - Page 65
    it. 2 Connect the scanner to a wired network (DR-S150 only) or Wi-Fi. For details, see "Setup Guide". 3 When using a Scanner Touch Panel You can copy a job registered in the CaptureOnTouch Job Tool to the scanner, you can scan documents according to those scan job settings by operating the scanner
  • Canon imageFORMULA DR-S150 | User Guide - Page 66
    a smart device, you can change the screen displayed at startup by tapping and selecting [Initial screen setting]. 2 Select the scanner. A Tap/click . B Select the scanner on the [Select Scanner] screen. IMPORTANT The maximum number of jobs that can be copied is 99. 6 Tap (Shared Folder) on the
  • Canon imageFORMULA DR-S150 | User Guide - Page 67
    To delete jobs registered in CaptureOnTouch Job Tool (when using a smart device) 1 Press and hold the icon of a job you want to delete. appears to indicate it is ready to be deleted. To delete jobs registered in CaptureOnTouch Job Tool (when using a computer) Deleting selected jobs 1 Click the icon
  • Canon imageFORMULA DR-S150 | User Guide - Page 68
    registered in CaptureOnTouch Job Tool (when using a computer)" on p. 67. Hint To delete all jobs copied to the scanner, delete all jobs from the CaptureOnTouch Job Tool. 2 Select the scanner. A Tap/click . 4 Enter the administrator password. Enter the same password as for the Web menu. For details
  • Canon imageFORMULA DR-S150 | User Guide - Page 69
    are displayed. These settings will apply when [Default] is clicked in the ISIS driver dialog box. When you scan a document in an ISIS compatible or TWAIN compatible application, open the scanner driver and configure the scanning conditions and other settings. This section describes the configuration
  • Canon imageFORMULA DR-S150 | User Guide - Page 70
    [Image processing] tab [Brightness] tab Set the processing method for scanned images. [Image control] tab Adjust the brightness and contrast of scanned images. In addition, you can also click [Gamma] and set the gamma correction value for scanned images. Set the image control method for the
  • Canon imageFORMULA DR-S150 | User Guide - Page 71
    ] tab Specify scanner operations related to document feeding. [Error Detection] tab Configure special scan method and image processing settings. User's Guide Set the items to be detected as errors during the scan. Informs you about the settings changed automatically by the driver. In addition
  • Canon imageFORMULA DR-S150 | User Guide - Page 72
    When the scanner driver is opened from CaptureOnTouch, the following settings screen of the scanner driver appears. Hint When the Advanced Settings screen is called from some applications, the Advanced Settings screen may have the Simple mode and Advanced mode. Simple Mode Advanced Mode 72
  • Canon imageFORMULA DR-S150 | User Guide - Page 73
    This section provides an overview of the basic setting items that are the minimum requirements when configuring the scanner settings. [Detect automatically] detects whether the document is in color, grayscale, or black and white. You can configure advanced settings related to the detection method
  • Canon imageFORMULA DR-S150 | User Guide - Page 74
    per inch], [Page Size], and [Scanning Side] basic conditions in the settings screen of the scanner driver. Color mode Select the scanning mode. • [Active Threshold] is intended for batch processing various kinds of documents at once, such as those with thin (light) text or stains. For example, you
  • Canon imageFORMULA DR-S150 | User Guide - Page 75
    page], the images of blank pages are deleted when images are saved. Configuring the following settings allows you to scan a document of an unregistered page size. When scanning a document of a non-standard page size, select [Add/ Delete] for [Page Size] to display the [Add/Delete Page Size] dialog
  • Canon imageFORMULA DR-S150 | User Guide - Page 76
    when [Check the image of the first page] is selected, only one page of the document is scanned and the corresponding scanned image is displayed in the preview window. Configuring Scanner Settings According to Purpose Set the scanning conditions according to the scanning purpose. When you want
  • Canon imageFORMULA DR-S150 | User Guide - Page 77
    Set the scanning side setting to [Skip blank page] to delete the images of the blank pages in the document. When you want to enhance contours in images Adjust the edge emphasis setting on the [Image control] tab. If [Skip blank page] is selected, you
  • Canon imageFORMULA DR-S150 | User Guide - Page 78
    When you want to reduce the moire patterns that appear when color photos in magazines and other documents are scanned at low resolutions Click [Image processing], and then configure moire reduction settings in the dialog box that appears. Setting [Moire Reduction] on the [
  • Canon imageFORMULA DR-S150 | User Guide - Page 79
    When you want to reduce the color unevenness Check the check box of [Color unevenness reduction] on the [Image control] tab to reduce the color unevenness. Click [Image processing], and then set [Color Unevenness reduction] to [ON] in the dialog box that appears. You can adjust the level of color
  • Canon imageFORMULA DR-S150 | User Guide - Page 80
    When you want to make lines and text in scanned images thicker or thinner When you want to reverse black and white in scanned images Drag the [Character Emphasis] slider in the [Image processing] tab to make lines and text in the scanned images thicker or thinner. Select [Reverse Image] on the [
  • Canon imageFORMULA DR-S150 | User Guide - Page 81
    the text is emphasized for better readability. You can select from the following functions. • [Advanced Text Enhancement II] is suitable for scanning a document with a uniform background color and light text and background. If the background is non-uniform, such as a pattern, the background may not
  • Canon imageFORMULA DR-S150 | User Guide - Page 82
    match the orientation of images to the text when scanning a mixture of pages with different text orientations Select [Text orientation recognition] in [Document Orientation] on the [Others] tab. The text orientation on each page is detected, and the scanned image is rotated in 90-degree increments
  • Canon imageFORMULA DR-S150 | User Guide - Page 83
    rotated in 90-degree increments to correct the orientation. When you want to rotate the images of a document placed horizontally to correct the orientation Specify the rotation angle in [Document Orientation] on the [Others] tab. Hint When the [Text Orientation Recognition] check box is selected
  • Canon imageFORMULA DR-S150 | User Guide - Page 84
    , you can separate a batch at the timing with which each next document is placed and scanned. (Only enabled for applications that support batch separation.) In this case, set the scanner driver as follows. • Set [Feeding Option] on the [Feeding] tab to [Panel-Feeding] or [Automatic Feeding]. • Set
  • Canon imageFORMULA DR-S150 | User Guide - Page 85
    then configure the setting items in the following order. A When you want to specify different scanning conditions for the front and back pages of a document, select [Duplex] for [Scanning Side] on the [Basic] tab in advance. B Specify the number of scanning conditions to apply in [Stream count of
  • Canon imageFORMULA DR-S150 | User Guide - Page 86
    D When specifying the scanning conditions of the back, configure the settings in the same way as described in B to C. In this case, specify [Stream count of Back], and then set the scanning conditions for each of [Back 1st] to [Back 3rd]. Hint The following shows the setting conditions that can be
  • Canon imageFORMULA DR-S150 | User Guide - Page 87
    You can remove dots and notches protruding from object outlines that appear in documents from scanned images. Click [Image processing] and select [ON] for [Erase Dot] or [Erase Notch] in the dialog box that appears. • Select the [Erase Dot]
  • Canon imageFORMULA DR-S150 | User Guide - Page 88
    When you want to save a scanner driver setting When you finish configuring a setting, click the [Save] button of [User Preference] to save the setting. The saved setting is registered to the list. You can delete a setting from the list with the [Delete] button, and
  • Canon imageFORMULA DR-S150 | User Guide - Page 89
    Function Restrictions Depending on Color Mode Setting Some of the setting items in each of the driver tabs are disabled as follows depending on the setting for [Color Mode] on the [Basic] tab. [Brightness] tab [Others] Tab Setting value Detect Automatically Active
  • Canon imageFORMULA DR-S150 | User Guide - Page 90
    box. Some of the setting items are disabled as follows depending on the setting for [Color Mode] in the settings screen of the scanner driver. Simple Mode Setting value Detect automatically Black and White Error Diffusion Advanced Text Enhancement II 256-level Gray 24-bit Color Check the image
  • Canon imageFORMULA DR-S150 | User Guide - Page 91
    Advanced Mode Setting value Enable Back Side Brightness Enable Back Side Contrast Check the image of the first page Detect automatically O O X Black and White O O O Error Diffusion O O O Advanced Text Enhancement II X X O 256-level Gray O O O 24-bit Color O O O O:
  • Canon imageFORMULA DR-S150 | User Guide - Page 92
    Type] of the [Feeding] tab, a part of the settings in each tab of the driver will be disabled, in the following manner. Document type Plain paper Carrier sheet Carrier sheet (for passports) Ultrasonic Double Feed Detection O X X (O: Available for setting, X: Not available for setting) 92
  • Canon imageFORMULA DR-S150 | User Guide - Page 93
    ) when documents containing blank pages are scanned. On the [Others] tab of the driver properties, DR-S150/DR-S130 supports batch separation (automatic file separation) functions by using patchcodes. By tucking patchcode sheets supplied with this scanner into a document and scanning it, the scanner
  • Canon imageFORMULA DR-S150 | User Guide - Page 94
    . 1 Print patchcode with a printer. Click [Start] - [Canon DR-S100 Series] and then select [Patchcode] from the menu. Patchcodes can be printed in A4 and letter (LTR) sizes. Open the application and print a patchcode that is the same size as the document to be scanned. Hint In Windows 8.1, it is
  • Canon imageFORMULA DR-S150 | User Guide - Page 95
    the page that separates the files. Insert the patchcode sheets at the beginning of documents to change file separation. 3 In an application, specify a patchcode as a type of batch separation. Open the scanner driver settings screen and select [Patchcode] in [Batch Separation] on the [Others] tab. 95
  • Canon imageFORMULA DR-S150 | User Guide - Page 96
    Using the Web Menu The Web menu is used to display information about the scanner, to set up the network when connecting via wired LAN (DR-S150 only) or Wi-Fi, and to configure various Web services. Scanner settings can be configured using a Web browser. IMPORTANT • We recommend the following Web
  • Canon imageFORMULA DR-S150 | User Guide - Page 97
    DR-S150 DR-S130 IMPORTANT To ensure security, we recommend changing the administrator password Setting" (See p. 105) 5 Click [Login]. The [Device information] screen appears. 1 Open the Canon imageFORMULA Driver Setting Tool's Settings screen. (See p. 114) 2 Click the [Network monitor] tab. 97
  • Canon imageFORMULA DR-S150 | User Guide - Page 98
    ]. WebScanSettingTool starts. Web Menu Pages When you click the items on the left menu, the following pages are displayed. Scanner Name Setting: Displays the scanner name. Network Setting: Configures the network settings. Device Configuration: Configures the mDNS, SNMP, PIN and COT Admin settings
  • Canon imageFORMULA DR-S150 | User Guide - Page 99
    DHCP protocol. To assign an IP address using ON DHCP, the DHCP server must be running in your subnetwork. Set the IP address of the scanner. If DHCP is enabled, the IP address obtained from it will be applied. The value must be four decimal numbers separated by dots and expressed
  • Canon imageFORMULA DR-S150 | User Guide - Page 100
    same subnetwork as the scanner. If [0.0.0.0] is set, this setting is disabled. None Device Configuration If you click [Device Configuration] on the left menu, the page below is displayed. Item mDNS Setting SNMP Setting PIN Setting COT Admin Connection Setting* * DR-S150 only. Description Moves
  • Canon imageFORMULA DR-S150 | User Guide - Page 101
    the setting is disabled, you must manually specify the scanner using its assigned IP address to scan from the scanning application. SNMP Setting If you click [SNMP Setting] on the Device Configuration screen, the page below is displayed. Item SNMP Service Location Security Auth trap SNMP v1
  • Canon imageFORMULA DR-S150 | User Guide - Page 102
    press the [Apply] button if the name is already being used or contains illegal characters. None Set either [Read/Write] or [Read only] as the user rights. Read only Sets permission to access the host. All hosts: Permits access to all hosts. Listed hosts: Permits access only to hosts specified in
  • Canon imageFORMULA DR-S150 | User Guide - Page 103
    name. You can specify a maximum of 5. You can input up to 64 characters in each line. None User Setting In the SNMP settings screen, enable the SNMP v3 support function and click [User Setting] to open the page shown in the following diagram. Item Modify Delete Detail info Description Change the
  • Canon imageFORMULA DR-S150 | User Guide - Page 104
    restrict Set either [Read/Write] or [Read only] as the user rights. Read only Authentication Specify MD5 or SHA1 as the algorithm Default Value OFF 0000 None None COT Admin Connection Setting (DR-S150 only) If you click [COT Admin Connection Setting] on the Device Configuration menu, the page
  • Canon imageFORMULA DR-S150 | User Guide - Page 105
    Input the IP address and the port number. Connection Test the connection with the COT test Admin server. Import root certificate You can replace the Set the administrator password (up to 32 characters) for the scanner. This password is used for authentication when configuring settings by Web
  • Canon imageFORMULA DR-S150 | User Guide - Page 106
    's factory default settings. If you click [Initialize] and then [Yes] in the screen that appears, the scanner's factory default settings are restored, and the scanner restarts. Update the scanner's firmware. Click [Version up], and specify the firmware file in the screen that appears. You can load
  • Canon imageFORMULA DR-S150 | User Guide - Page 107
    . Cleaning the Sensor Glass and the Rollers If scanned images contain streaks, or if the scanned documents become dirty, the sensor glass or rollers inside the scanner may be dirty. Clean them periodically. 1 Pull the OPEN lever and pull open the front unit toward you. Cleaning the touch panel
  • Canon imageFORMULA DR-S150 | User Guide - Page 108
    Glass CAUTION Do not spray water or neutral detergent directly on the scanner. Precision mechanisms, such as the light source, may get wet, and are scratches on the sensor glass, contact your local authorized Canon dealer or service representative. • Take care to ensure the anti-static brush
  • Canon imageFORMULA DR-S150 | User Guide - Page 109
    retard roller and feed roller. (See p. 111, p. 112) IMPORTANT Remove the retard roller and feed roller from the scanner to clean them, and be sure to reattach them to the scanner when cleaning is finished. 6 Wipe the removed rollers with a cloth that has been dampened with water and thoroughly wrung
  • Canon imageFORMULA DR-S150 | User Guide - Page 110
    Consumable Parts The two rollers (feed roller and retard roller) installed in the scanner are consumable parts. The feed roller and retard roller wear with scanning. If the feed roller and retard roller are worn, documents may not feed correctly and paper jams and double feeds may occur. When more
  • Canon imageFORMULA DR-S150 | User Guide - Page 111
    Opening and Closing the Front Unit 1 Pull the OPEN lever and pull open the front unit toward you. 2 When closing the front unit, make sure that it is completely closed by gently pressing the left and right until you hear a click. Hint The location of each of the consumable parts is shown below.
  • Canon imageFORMULA DR-S150 | User Guide - Page 112
    2 Remove the feed roller. 3 Install the new feed roller. 4 Close the roller cover. Replacing the Retard Roller 1 Open the roller cover. 2 Pull the left lever that secures the retard roller to the scanner, and remove the roller. ▼ 112
  • Canon imageFORMULA DR-S150 | User Guide - Page 113
    Install the new retard roller by inserting the right side first. 4 Push the left side of the retard roller to secure it to the scanner. 5 Close the roller cover. Resetting the counter 1 Tap (Settings) button on the touch panel. The settings menu screen appears. 2 Tap [Maintenance] and then [Roller
  • Canon imageFORMULA DR-S150 | User Guide - Page 114
    screen to make various scanner settings. "Web Menu" (See p. 96) IMPORTANT A USB connection is required to make this setting with the Canon imageFORMULA Driver Setting Tool. When connected via wired LAN (DR-S150 only) or Wi-Fi, making this setting with the Canon imageFORMULA Driver Setting Tool is
  • Canon imageFORMULA DR-S150 | User Guide - Page 115
    Start-up of the Canon imageFORMULA Driver Setting Tool Click the Start button, then click [Canon DR-S100 Series] - [Canon imageFORMULA Driver Setting Tool] in that order. Canon imageFORMULA Driver Setting Tool will start. Hint In Windows 8.1, it is registered at the following location. 115
  • Canon imageFORMULA DR-S150 | User Guide - Page 116
    Troubleshooting Common Problems and Solutions This section provides recommended solutions to common problems. If you have a problem that is not solved by the following, contact your local authorized Canon dealer. Problem 1 The scanner When connecting via wired LAN (DR-S150 only)/Wi-Fi (common):
  • Canon imageFORMULA DR-S150 | User Guide - Page 117
    the stealth function or use manual setup to enter the correct SSID of the access point. (7) When the access point's MAC filtering function is enabled, the MAC address of this scanner must be registered. (8) Wi-Fi connections are not recognized when connected via wired LAN (DR-S150 only) or when
  • Canon imageFORMULA DR-S150 | User Guide - Page 118
    by cleaning, the internal glass may be scratched. Contact your local authorized Canon dealer. Problem 11 Pages are missing. Solutions When the scanner driver's [Scanning Side] setting is [Skip Blank Page], documents with very little black may be unintentionally skipped. Decrease the Set the
  • Canon imageFORMULA DR-S150 | User Guide - Page 119
    are set to on. Problem 16 Double-feeding occurs when scanning a document with multiple pages. Solutions Turn on [Disable double-feed detection] on the touch panel to continue scanning (See p. 49), or set the [Detect by Ultrasonic] check box to off in the scanner driver's settings screen. (See
  • Canon imageFORMULA DR-S150 | User Guide - Page 120
    , and then scan again. (See p. 73) (2) Set [Dots per inch] to 300 dpi or less on the scanner driver settings screen. (See p. 73) (3) Clean the roller. Problem 18 The size detection and deskew functions fail. Solutions When [Document Type] is set to [Carrier sheet] in the [Feeding] tab of the
  • Canon imageFORMULA DR-S150 | User Guide - Page 121
    troubleshooting problems scanner directly to the computer. (7) If a message is displayed on the touch panel indicating scanning in the Long Document mode, deselect the Long Document multi- page) can only be opened by programs that support the compressed format. This can occur with programs that are
  • Canon imageFORMULA DR-S150 | User Guide - Page 122
    page files. See also "Problem 13" in "Common Problems and Solutions". Can I copy or back up scanner setting configurations? The setting 31. How do I load and scan documents with mixed sizes? Set [Page Size] to [Match original size] on the scanner driver setting screen, then scan. For details,
  • Canon imageFORMULA DR-S150 | User Guide - Page 123
    a plug-in. • By installing the plug-in, the scanned image can be printed, attached in an e-mail, or shared using various cloud services. • The plug-in can be installed by selecting its checkbox when installing CaptureOnTouch. • The available output destinations vary depending on the installed plug
  • Canon imageFORMULA DR-S150 | User Guide - Page 124
    Jam When paper jams are detected during scanning, the following error codes are displayed in the touch panel and scanning is interrupted. 1 Remove any documents that have been left in the feed Tray. When a paper jam or double feed occurs during scanning, use the following procedures to clear
  • Canon imageFORMULA DR-S150 | User Guide - Page 125
    . Hint The following message appears on the touch panel when the front unit is open. IMPORTANT Make sure to pull the document out carefully, without applying too much force. If the jammed paper tears while you are pulling it out, make sure to remove any remaining pieces
  • Canon imageFORMULA DR-S150 | User Guide - Page 126
    . Hint When the [Rapid recovery system] check box is enabled in the scanner driver settings screen, you can resume a scanning operation even if it is interrupted by a paper jam by removing the document and resuming from the document that was being fed when the interruption occurred. As the image of
  • Canon imageFORMULA DR-S150 | User Guide - Page 127
    instructions in the User Manual. The number of scanned pages has exceeded 200,000, which exceeds the number of pages for the service life of the rollers. Paper jammed in scanner, clear paper and continue. Paper jammed while scanning. A double paper-feed has occured. Please check the document
  • Canon imageFORMULA DR-S150 | User Guide - Page 128
    Uninstalling the Software Some scanner malfunctions can be resolved by reinstalling the software. Before reinstalling the software, make sure to completely uninstall any previous installation first. Uninstalling the ISIS/TWAIN Driver The following procedure uses the ISIS/TWAIN driver as an example
  • Canon imageFORMULA DR-S150 | User Guide - Page 129
    356 mm (2.1" to 14") (You can scan documents up to 3,000 mm (118.1") long by setting the scanner to the Long Document mode.) Paper weight: Page separation: 27 to 209 : Core i7 2.8GHz CPU, 4 GB memory, A4 document size) DR-S150 Grayscale Simplex 200dpi 45 pages/min 300dpi 45 pages/min Duplex
  • Canon imageFORMULA DR-S150 | User Guide - Page 130
    your local authorized Canon dealer or service representative for scanner unit102 (product code: 2152Cxxx) Flatbed scanner unit that can be connected to and used with a DR scanner. Connecting the unit to this scanner enables you to use this scanner as a flatbed scanner with an automatic document
  • Canon imageFORMULA DR-S150 | User Guide - Page 131
    memory, CaptureOnTouch cannot be restarted by pressing the start button on Flatbed Scanner Unit after you end CaptureOnTouch. About Setting up the Scanner Driver When functions of this scanner cannot be selected with the Flatbed Scanner Unit settings dialog box, click [Option] in the dialog box to
  • Canon imageFORMULA DR-S150 | User Guide - Page 132
    32 Front unit 111 L Long Document Mode 38 M Multi-stream setting 85 P Paper Feed Tray with NFC Reader 130 Paper jam Passports ...3..6..,.. 124 130 Power supply 10 R Retard roller 110, 112 Roller 108 Cleaning 107 Replace 110 S Scan area 76 Scanner driver 69 Basic settings 73
  • Canon imageFORMULA DR-S150 | User Guide - Page 133
  • Canon imageFORMULA DR-S150 | User Guide - Page 134
  • Canon imageFORMULA DR-S150 | User Guide - Page 135
    SHIBAKOEN, MINATO-KU, TOKYO 105-0011, JAPAN CANON U.S.A. INC. ONE CANON PARK, MELVILLE, NY 11747, U.S.A. CANON CANADA INC. 8000 Mississauga Road Brampton, Ontario L6Y 5Z7, CANADA CANON EUROPA N.V. BOVENKERKERWEG 59, 1185 XB AMSTELVEEN, THE NETHERLANDS CANON AUSTRALIA PTY. LTD. BUILDING A, THE PARK
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
User Manual
• Please read this manual before operating this
scanner.
• After you finish reading this manual, store it in a safe
place for future reference.