Casio W93H-1AV User Guide

Casio W93H-1AV - Mens Manual

Casio W93H-1AV manual content summary:

  • Casio W93H-1AV | User Guide - Page 1
    term use. • Frequent use of the backlight shortens the battery life. • The watch emits an audible sound whenever the display is illuminated. This from the beginning without stopping. You can stop the countdown by pressing D and manually reset to the start time by pressing B. • If you set a starting
  • Casio W93H-1AV | User Guide - Page 2
    About the Auto-Start function With the Auto-Start function, the watch performs a 5-second countdown. When the countdown reaches zero, stopwatch after it starts to sound. When the Current time Hourly Time Signal is on, the watch beeps every hour on the hour. To set the alarm time 1. Hold down A
  • 1
  • 2

1949-1
Module No. 1949
GENERAL GUIDE
Press
C
to change from mode to mode.
After you perform an operation in any mode, pressing
C
returns to the Timekeeping Mode.
If you do not press any button for a few minutes while making settings in any mode (indicated when settings are flashing), the watch automatically clears the setting screen (settings stop
flashing) and returns to the normal display for the mode you are in.
This watch returns to the Timekeeping Mode whenever you hold down the
C
button for one or two seconds. If you ever lose track of what mode you are in or what you should do next,
hold down
C
to return to normal timekeeping.
In any mode press
L
to illuminate the display.
TIMEKEEPING MODE
To set the time and date
1. Hold down
A
while in the Timekeeping Mode until the
seconds digits flash on the display because they are
selected
.
2. Press
C
to change the selection in the following se-
quence.
Seconds
Day
Minutes
12/24-Hour Format
Hour
Day of week
Month
3. While the seconds digits are selected (flashing), press
D
to reset the seconds to
00.
If you press
D
while the seconds count is in the range of 30 to 59, the seconds
are reset to 00 and 1 is added to the minutes.
If the seconds count is in the range
of 00 to 29, the minutes count is unchanged.
4. While any other digits (beside seconds) are selected (flashing), press
D
to in-
crease the number or
B
to decrease it.
While the 12/24-hour format setting is
selected, press
D
or
B
to toggle it between 12 and 24. While the day of the week
is selected (flashing), press
D
to advance to the next day or
B
to return to the
previous day.
Except for when adjusting the seconds or setting the 12/24-hour format, holding
down a button changes the current selection at high speed.
When the 12-hour format is selected, the indicator
P
appears on the display to
indicate “P.M.” times.
There is no indicator for “A.M.” times.
When the 24-hour format is selected, the indicator
24
appears on the display.
5. After you set the time and date, press
A
to return to the Timekeeping Mode.
ABOUT THE BACKLIGHT
About the Auto Light Switch Function
When the auto light switch function is turned on, the backlight automatically turns on
for two seconds under the conditions described below. Avoid wearing the watch on
the inside of your wrist. Doing so causes the auto light switch to operate when not
needed, which shortens battery life.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you approximately 40 degrees causes the backlight to illuminate.
The backlight may not illuminate if the face of the watch is more than 15 degrees off
parallel to the left or right. Make sure that the back of your hand is parallel to the
ground.
Static electricity or magnetic force can interfere with proper operation of the auto
backlight function. If the auto backlight does not illuminate, try moving the watch
back to the starting position (parallel with the ground) and then tilt it back toward
you again. If this does not work, drop your arm all the way down so it hangs at your
side, and then bring it back up again.
Under certain conditions the backlight may not light until about one second or less
after turning the face of the watch towards you. This does not necessarily indicate
malfunction of the backlight.
To switch the auto light switch function on and off
In the Timekeeping Mode, hold down
B
for one or two seconds to turn the auto light
switch function on and off.
ON
OFF
The auto light switch indicator is shown on the display in all modes while the auto
light switch function is on.
In order to protect against running down the battery, the auto light switch function is
automatically turned off approximately three hours after you turn it on. Repeat the
above procedure to turn the auto light switch function back on if you want.
Pressing
L
while in the Timekeeping Mode illuminates the display, regardless of
the auto light switch’s on/off setting.
Caution
The backlight of this watch employs an electro-luminescent (EL) light, which loses
its illuminating power after very long term use.
Frequent use of the backlight shortens the battery life.
The watch emits an audible sound whenever the display is illuminated. This is be-
cause the EL light vibrates slightly when lit. It does not indicate malfunction of the
watch.
Warning!
Never try to read your watch when mountain climbing or hiking in areas that
are dark or in areas with poor footing.
Doing so is dangerous and can result
in serious personal injury.
Never try to read your watch when running where there is the danger of acci-
dents, especially in locations where there might be vehicular or pedestrian
traffic. Doing so is dangerous and can result in serious personal injury.
Never try to read your watch when riding on a bicycle or when operating a
motorcycle or any other motor vehicle. Doing so is dangerous and can result
in a traffic accident and serious personal injury.
When you are wearing the watch, make sure that its auto light switch function
is turned off before riding on a bicycle or operating a motorcycle or any other
motor vehicle.
Sudden and unintended operation of the auto light switch can create a dis-
traction, which can result in a traffic accident and serious personal injury.
COUNTDOWN ALARM MODE
The countdown alarm can be set within a range of 1 sec-
ond to 24 hours.
When the countdown reaches zero, an
alarm sounds for 10 seconds or until you press any but-
ton.
To set the countdown start time
1. Hold down
A
while in the Countdown Alarm Mode.
The
hours digits flash on the display because they are
se-
lected.
2. Press
C
to change the selection in the following se-
quence.
Hour
Minutes
Seconds
3. Press
D
to increase the selected number or
B
to decrease it.
Holding down either
button changes the selection at high speed.
Press
D
and
B
at the same time to clear the starting time to 0:00' 00".
To set the starting value of the countdown time to 24 hours, set 0:00' 00".
4. After you set the countdown start time, press
A
twice to return to the Countdown
Alarm Mode.
To use the countdown alarm
1. Press
D
while in the Countdown Alarm Mode to start the countdown alarm.
2. Press
D
again to stop the countdown alarm.
You can resume countdown alarm operation by pressing
D
.
3. Stop the countdown alarm and then press
B
to reset the countdown time to its
starting value.
When the end of the countdown is reached and auto repeat timing is off, the alarm
sounds for 10 seconds or until you stop the alarm by pressing any button.
Count-
down timing stops and the countdown time is automatically reset to its starting
value after the alarm stops.
To switch auto repeat timing and the progress beeper on and off
1. Hold down
A
while in the Countdown Alarm Mode.
The hour digits flash on the
display because they are
selected
.
Press
A
again to move the flashing to the auto
repeat ON/OFF setting.
2. Press
D
or
B
to toggle auto repeat on (
) and off.
3. Press
C
to move the flashing to the progress beeper ON/OFF setting.
4. Press
D
or
B
to toggle the progress beeper on (
) and off.
5. Press
A
to return to the Countdown Alarm Mode.
When the end of the countdown is reached while auto repeat is on, the alarm sounds,
but the countdown restarts from the beginning without stopping.
You can stop the
countdown by pressing
D
and manually reset to the start time by pressing
B
.
If you set a starting time of 10 seconds or less and have Auto Repeat turned on, the
countdown alarm tone (which normally sounds for 10 seconds) sounds for only one
second.
When the progress beeper is turned on, the watch beeps as the countdown time
passes the 10, 5, 4, 3, 2, and 1-minute marks, and the 50, 40, 30, 20, 10, 5, 4, 3, 2,
and 1-second marks.
Timekeeping Mode
Countdown Alarm Mode
Stopwatch Mode
Alarm Mode
Dual Time Mode
Day of week
Month - Day
PM indicator
Hour
Minutes
Seconds
Parallel to ground
40
°
Parallel to ground
More than 15 degrees too
high
More than 15 degrees
too low
Current time
Progress beeper on
indicator
Auto repeat on indicator
1/10
Seconds
Seconds
Minutes
Mode indicator
Auto light switch
indicator
Hold down
B
.