Cisco 3825 User Guide - Page 23

Mounting the Residential Gateway on a Wall, Important - end of support

Get Cisco 3825 - Voice Bundle Router PDF manuals and user guides
UPC - 746320981505
View all Cisco 3825 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

How Do I Mount the Modem on a Wall? (Optional) Mounting the Residential Gateway on a Wall 1 Using a drill with a 3/16-inch bit, drill two holes at the same height and 4 inches apart. Note: The preceding graphic illustrates the location of the mounting holes on the back of the residential gateway. 2 Are you mounting the residential gateway into a drywall or concrete surface where a wooden stud is available? „ If yes, go to step 3. „ If no, drive the anchor bolts into the wall, and install the mounting screws into the anchor bolts; leave a gap of about 1/4-inch between the screw head and the wall. Then, go to step 4. 3 Install the mounting screws into the wall; leave a gap of about 1/4-inch between the screw head and the wall. Then, go to step 4. 4 Verify that no cables or wires are connected to the residential gateway. 5 Lift the residential gateway into position. Slip the large end of both mounting slots (located in the back of the residential gateway) over the mounting screws, and then slide the residential gateway down until the narrow end of the keyhole slot contacts the screw shaft. Important: Verify that the mounting screws securely support the residential gateway before you release the unit. 4021196 Rev A 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
4021196 Rev A
23
How Do I Mount the Modem on a Wall? (Optional)
Mounting the Residential Gateway on a Wall
1
Using a drill with a 3/16-inch bit, drill two holes at the same height and 4 inches
apart.
Note:
The preceding graphic illustrates the location of the mounting holes on the
back of the residential gateway.
2
Are you mounting the residential gateway into a drywall or concrete surface
where a wooden stud is available?
If
yes
, go to step 3.
If
no
, drive the anchor bolts into the wall, and install the mounting screws
into the anchor bolts; leave a gap of about 1/4-inch between the screw head
and the wall. Then, go to step 4.
3
Install the mounting screws into the wall; leave a gap of about 1/4-inch between
the screw head and the wall. Then, go to step 4.
4
Verify that no cables or wires are connected to the residential gateway.
5
Lift the residential gateway into position. Slip the large end of both mounting
slots (located in the back of the residential gateway) over the mounting screws,
and then slide the residential gateway down until the narrow end of the keyhole
slot contacts the screw shaft.
Important:
Verify that the mounting screws securely support the residential
gateway before you release the unit.