Cisco 7604 Processor Guide

Cisco 7604 Manual

Get Cisco 7604 PDF manuals and user guides View all Cisco 7604 manuals
Add to My Manuals
Save this manual to your list of manuals

Cisco 7604 manual content summary:

  • Cisco 7604 | Processor Guide - Page 1
    Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide March 2012 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-10100-11
  • Cisco 7604 | Processor Guide - Page 2
    be required to correct the interference at their own expense. The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco's installation instructions, it
  • Cisco 7604 | Processor Guide - Page 3
    Hardware and Features 2-10 RSP720 with 10GE Uplink Ports 2-10 RSP720-10GE Features 2-11 Supported Chassis, Line Cards, and Modules 2-11 RSP720-10GE Usage Guidelines and Limitations 2-13 QoS on the RSP720-10GE 2-13 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7604 | Processor Guide - Page 4
    Feature Support 3-14 Upgrading DIMMs on RSP720 3-14 Configuring a Supervisor Engine or Route Switch Processor 3-17 Troubleshooting Route Switch Processors and Supervisor Engines 4-1 Getting Started 4-1 AC and DC Power Supply Information 4-1 Chassis and Supervisor Slot Installation 4-2 Cisco
  • Cisco 7604 | Processor Guide - Page 5
    Hardware and Features 4-2 RSP720-1GE Unsupported Hardware and Features 4-2 RSP720-10GE Supported Chassis, Line Cards, and Modules 4-3 RSP720-10GE Unsupported Chassis, Modules and Features 4-3 Obtaining Technical Assistance 4-3 Troubleshooting Supervisor Failures 4-4 Troubleshooting Back-Plane Data
  • Cisco 7604 | Processor Guide - Page 6
    -RJ Connectors B-17 LC Connectors B-17 Cleaning the Fiber-Optic Connectors B-18 LX/LH GBIC and MMF Cable Considerations B-19 Patch Cord B-19 Patch Cord Configuration Example B-19 Patch Cord Installation B-20 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide vi OL-10100-11
  • Cisco 7604 | Processor Guide - Page 7
    engines supported by Cisco 7600 series routers. It also provides technical specifications for these modules and describes cable and connector specifications. Caution Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS3260) should install, replace, or service the
  • Cisco 7604 | Processor Guide - Page 8
    Description Provides an overview of Cisco 7600 series routers, and interface and port addresses. Describes the route switch processors (RSPs) and supervisor engines supported on Cisco 7600 series routers. Provides instructions for installing and removing RSPs and supervisor engines and connecting
  • Cisco 7604 | Processor Guide - Page 9
    the cable and connector specifications for the RSPs and supervisor engines. Document Conventions This document uses the following conventions: Convention boldface font italic font Description Commands, command options, and keywords are in boldface. Command arguments for which you supply values
  • Cisco 7604 | Processor Guide - Page 10
    Installation Guide • Cisco 7609 Router Installation Guide (OSR-7609) • Cisco 7600 Series Router Module Installation Guide • Cisco 7600 Series Router Cisco IOS Command Reference • Cisco 7600 Series Router Cisco IOS System Message Guide • Cisco 7600 Series Router Cisco IOS Software Configuration Guide
  • Cisco 7604 | Processor Guide - Page 11
    Router Installation Guide. Cisco 7600 Series Routers The Cisco 7600 series routers consist of these routers: • Cisco 7603 router (3 slots) • Cisco 7604 router (4 slots) • Cisco 7606 router (6 slots) • Cisco 7609 router (9 vertical slots) • Cisco 7613 router (13 slots) Note In addition, Cisco IOS
  • Cisco 7604 | Processor Guide - Page 12
    for the Cisco 7613 router Note Specific combinations of supervisor engines or RSPs and modules may not be supported in your chassis. See the Supported Hardware for Cisco 7600 Series Routers guide for information about which combinations are not supported. • Hot-swappable fan assembly • Redundant AC
  • Cisco 7604 | Processor Guide - Page 13
    engine or route switch processor Description For detailed information about the features supported on Cisco 7600 series routers, see the Cisco 7600 Series Router Cisco IOS Software Configuration Guide for the version of software being used on the router. • Modular, upgradable feature modules for
  • Cisco 7604 | Processor Guide - Page 14
    route switch and redundancy processors, including fast switchover to the redundant (standby) module • Support for two redundant AC- or DC-input, load-sharing power supplies • Support for two redundant AC- or DC-input PEMs (Cisco 7603 and Cisco 7606 routers only) • Power management for modules
  • Cisco 7604 | Processor Guide - Page 15
    . Cisco IOS Release 12.2(18)SXF and later releases support the CF adapter as an orderable option (Cisco part number CF-ADAPTER=) for these Sups. Note In the command-line-interface (CLI), you access internal flash memory as bootdisk (CF adapter) or bootflash (non-CF adatper). When you install a CF
  • Cisco 7604 | Processor Guide - Page 16
    Routers Key Features (continued) Feature Description Component hot All components (including optional redundant modules and fans) support hot swapping, swapping which allows you to add, replace, or remove components without interrupting the system power or causing other software or interfaces
  • Cisco 7604 | Processor Guide - Page 17
    one unique MAC address. This addressing scheme enables the router to identify the state (connected or not connected) of each interface. When you hot swap a module, the MAC address changes with the module. OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 1-7
  • Cisco 7604 | Processor Guide - Page 18
    3 Multiprotocol. Supported Hardware The following 7600 chassis supports Supervisor Engine 2T: • 7609-S Features Supervisor Engine 2T delivers scalable performance, intelligence, and a broad set of features to address the needs of borderless networks, data centers, and service provider networks
  • Cisco 7604 | Processor Guide - Page 19
    chapter describes the route switch processors and supervisor engines supported on Cisco 7600 series routers and provides instructions for performing basic tasks on the modules. It contains the following sections: • Overview, page 2-2 • Route Switch Processor 720, page 2-9 • RSP720 with 10GE Uplink
  • Cisco 7604 | Processor Guide - Page 20
    or RSP, you can install another type of module in the slot reserved for the redundant supervisor engine or RSP. The supervisor engine or RSP contains the following integrated daughter cards that perform forwarding and routing and provide the protocols supported on the router. Several configurations
  • Cisco 7604 | Processor Guide - Page 21
    Tree Protocol (STP) and others. For information about supported protocols, see the Cisco 7600 Series Router Cisco IOS Software Configuration Guide and the release notes for the software version running on the router. OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor
  • Cisco 7604 | Processor Guide - Page 22
    the RSP and supervisor engine configurations supported on Cisco 7600 series routers. Specific combinations of processors and modules may not be supported in your chassis. See the release notes for your software version for information about supported combinations. Table 2-1 Route Switch Processor
  • Cisco 7604 | Processor Guide - Page 23
    to 1 GB) and two internal CompactFlash slots (one each for RP and SP, 512 MB default for each) • Requires larger power supplies and a high-speed fan tray • QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-5
  • Cisco 7604 | Processor Guide - Page 24
    • Requires larger power supplies and a high-speed fan tray • QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t Note Cisco IOS Release 12.2SXF is the last release in which the Sup720 with PFC3A is supported. • Two Gigabit Ethernet uplink ports: port 1 supports a 1-Gbps SFP module; port 2 is configurable
  • Cisco 7604 | Processor Guide - Page 25
    • Two CompactFlash Type II slots • Requires larger power supplies and a high-speed fan tray • QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t Note A CompactFlash (CF) adapter with 512-MB bootdisk is available for Sup720 modules in Release 12.2(18)SXF and later releases. Use the Cisco part number CF
  • Cisco 7604 | Processor Guide - Page 26
    Engine Configurations (continued) Product Number Description WS-X6K-S2-PFC2 • Two dual-port 1000BASE-X GBIC uplinks • PFC2; fabric enabled, supports optional SFM2 • QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t WS-X6500-SFM2 • (Optional) SFM2 Note The Sup2 is not supported in Cisco IOS
  • Cisco 7604 | Processor Guide - Page 27
    chassis) except the Cisco 7603 and the Cisco OSR-7609. • Cisco IOS Release 12.2SRC and later releases support an RSP720 that has 10GE uplinks (RSP720-3C-10GE and RSP720-3CXL-10GE). See the "RSP720 with 10GE Uplink Ports" section on page 2-10 for more information. Figure 2-1 shows the RSP720-3C-GE
  • Cisco 7604 | Processor Guide - Page 28
    which require CFC or DFC): - WS-X67xx - WS-X65xx - WS-X64xx - WS-X63xx - WS-X61xx Unsupported Hardware and Features The following hardware and features are not supported by the RSP720: • Unsupported chassis: Cisco 7603, Cisco OSR-7609. • Unsupported modules: Services modules, Optical Service Modules
  • Cisco 7604 | Processor Guide - Page 29
    10GE. Supported Chassis, Line Cards, and Modules The RSP720-10GE supports the following chassis and modules: • Supported on the Cisco 7604 and 7609 chassis and the Cisco 7603-S, 7606-S, and 7609-S chassis OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-11
  • Cisco 7604 | Processor Guide - Page 30
    Chassis and Modules The RSP720-10GE does not support the following chassis and modules: • Unsupported chassis: Cisco 7603, 7606, and 7613 chassis • Unsupported modules: Services modules, Optical Service Modules (OSMs), FlexWAN module Unsupported Features In Cisco IOS Release 12.2SRC, the RSP720
  • Cisco 7604 | Processor Guide - Page 31
    the RSP720, Cisco IOS software boots up but the software detects a mismatch and enters ROMMON mode. • You can configure the RSP720-10GE to run QoS features on all uplink ports (10GE and 1GE) or on 10GE ports only. A new CLI command (mls qos supervisor 10g-only) is available to configure the module
  • Cisco 7604 | Processor Guide - Page 32
    to resume QoS service on those ports. • In 10GE only mode, the 1GE ports are visible but they remain in an administratively down state. Configuring 10GE Only QoS Cisco IOS Release 12.2SRC introduces a new command to enable QoS features on 10GE uplink ports only. By default, the router runs in mixed
  • Cisco 7604 | Processor Guide - Page 33
    use X2 as transceiver, and the three 1GE ports use SFP. The uplink ports are configurable with SFP or X2 optics modules. See the "Connecting to the Uplink Ports" section on page 3-10 for more information. OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-15
  • Cisco 7604 | Processor Guide - Page 34
    slot-no led beacon command to configure the LED. All chassis environmental monitors are reporting OK. The module is powering up or a minor hardware fault has occurred. Major hardware problem. The temperature of the supervisor engine has exceeded the major temperature threshold. Continuous backplane
  • Cisco 7604 | Processor Guide - Page 35
    Features and Benefits details This section provides details of scalability and performance capabilities of Supervisor Engine 2T and functions supported. Table 2-4 shows the scalability for Supervisor Engine 2T. Table 2-4 Scalability Name IPv4 routing IPv6 routing L2 bridging VS-S2T-10G In hardware
  • Cisco 7604 | Processor Guide - Page 36
    (Up to 390 Mpps**) Hardware assisted 128k 256K(IPv4) 128K (IPv6) 512K 128K (IPv4) 128K (IPv6) In hardware (Up to 390 Mpps**) In hardware (Up to 390 Mpps**) Hardware assisted 128k 1024K (IPv4) 512K (IPv6) 1024K 128K (IPv4) 128K (IPv6) Table 2-5 shows the QoS features and scalability for Supervisor
  • Cisco 7604 | Processor Guide - Page 37
    -XL Yes Yes Yes Yes 256K shared for QOS/Security 57 Up to 16 16k 16 Yes Yes 128k 8 bits Yes Yes L2 and L3 support Yes Yes 16K 8K Yes Yes Table 2-7 shows the MPLS and virtualization features for Supervisor Engine 2T. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-19
  • Cisco 7604 | Processor Guide - Page 38
    NAT Yes VRF-lite scalability VLAN reuse per sub-interface Per VPN interface statistics Yes VS-S2T-10G-XL Yes Yes Yes Yes Yes Yes Yes Yes Yes 16k Yes Yes Yes Yes Yes VLAN reuse per sub-interface Yes 2-20 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7604 | Processor Guide - Page 39
    Panel Controls (RSP720, RSP720-10GE, Sup720, Sup32) Table 2-8 describes the front-panel controls on the Route Switch Processor 720 and RSP720-10GE, the Supervisor Engine 720, and the Supervisor Engine 32. OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-21
  • Cisco 7604 | Processor Guide - Page 40
    . The module is powering up or a minor hardware fault has occurred. Major hardware problem. The temperature of the supervisor engine or RSP has exceeded the major temperature threshold. Continuous backplane stall. 2-22 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL
  • Cisco 7604 | Processor Guide - Page 41
    Orange Green The supervisor engine or RSP is powering up or is in standby mode. Sufficient power is available for all modules installed in the router. Orange The supervisor engine or RSP is powering up or has minor hardware problems. Red Major hardware problem. DISK Green The disk is active
  • Cisco 7604 | Processor Guide - Page 42
    ; the module is not operational. (The fault occurred during the initialization sequence.) An overtemperature condition has occurred. (A major threshold has been exceeded during environmental monitoring.) 2-24 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100
  • Cisco 7604 | Processor Guide - Page 43
    The VTT module terminates signals on the system switching bus. 3. If no redundant supervisor engine is installed and there is a VTT module minor or major overtemperature condition, the system shuts down. OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-25
  • Cisco 7604 | Processor Guide - Page 44
    Supervisor Engine 2 Chapter 2 Route Switch Processors and Supervisor Engines 2-26 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7604 | Processor Guide - Page 45
    chassis slot to install the module in. (See the "Determining Module Location" section on page 3-3.) • Consider cabling for the console and uplink ports. (See Appendix B, "Cable and Connector Specifications.") OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7604 | Processor Guide - Page 46
    3 Installing and Configuring Route Switch Processors and Supervisor Engines Safety Precautions for Module Installation and Removal Be sure to observe the following warnings and safety precautions when you work on the router. Warning Hazardous voltage or energy is present on the backplane when
  • Cisco 7604 | Processor Guide - Page 47
    chassis) • Not supported in the 3-slot chassis • Slots 1 and 2 (3-slot and 4-slot chassis) • Slots 5 and 6 (6-slot and 9-slot chassis) • Slots 7 and 8 (13-slot chassis) • Slots 5 and 6 (9 slot 7609-S chassis). OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7604 | Processor Guide - Page 48
    installed modules will push adjacent modules toward the open slot, which reduces the opening size and makes it difficult to install the new module. Step 3 Fully open both ejector levers on the new module. (See Figure 3-1.) Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7604 | Processor Guide - Page 49
    Captive Ejector lever installation screws Step 4 Position the module in the slot. Make sure that you align the sides of the module with the guides on each side of the slot. (See Figure 3-2.) Figure 3-2 Positioning the Module in the Slot Insert module between slot guides 3 EMI gasket 1 2 36
  • Cisco 7604 | Processor Guide - Page 50
    installation screws. Note Blank module filler plates (Cisco part number 800-00292-01) should be installed in any empty chassis slots to keep dust out of the chassis and to maintain consistent airflow through the chassis. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7604 | Processor Guide - Page 51
    engine or RSP. If the module is running Cisco IOS software, save the current running configuration by entering the copy running-config startup-config command. Warning Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing. Statement 1034
  • Cisco 7604 | Processor Guide - Page 52
    Installing and Configuring Route Switch Processors and Supervisor Engines Hot Swapping (OIR) Modules Cisco 7600 series routers provide a feature that allows you to remove and replace a redundant supervisor engine or route switch processor (and other redundant cards) without powering down the router
  • Cisco 7604 | Processor Guide - Page 53
    on a route switch processor or supervisor engine. You must connect to the router through the console port to configure the router for the first time. You can also connect to the console port to perform diagnostics and troubleshoot problems on the router. For console cabling specifications, see the
  • Cisco 7604 | Processor Guide - Page 54
    Do not remove the plugs from the optical bores on the fiber-optic cable or the module port or until you are ready to connect the cable. The plugs protect the optical bores and cable from contamination. 3-10 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7604 | Processor Guide - Page 55
    10-Gigabit Ethernet uplink ports. The Gigabit Ethernet uplink ports require XENPAK optics modules to be installed into them. The ports operate at 10 Gbps. • Two dual-port Gigabit Ethernet ports operate in full-duplex mode only. • You can configure the ports with any combination of copper, short-wave
  • Cisco 7604 | Processor Guide - Page 56
    and the MMF cable. For instructions, see the "Patch Cord" section on page B-19. Note • If two RSPs or supervisor engines are installed, the uplink ports on the redundant (standby) module are active and can be used for normal traffic like any other ports in the chassis. • In Cisco IOS Release 12.2SRC
  • Cisco 7604 | Processor Guide - Page 57
    Chapter 3 Installing and Configuring Route Switch Processors and Supervisor Engines Using Flash Memory Cards Note Not all flash memory cards have a write-protection switch. Table 3-3 lists the Cisco product numbers of memory cards supported on Cisco 7600 supervisor engines and route switch
  • Cisco 7604 | Processor Guide - Page 58
    features are supported on the router and the minimum Cisco IOS software requirements for the hardware installed on your router. Note You must have an account on Cisco.com to access the Feature Navigator or Software Advisor tool. • To determine which software features are supported by your route
  • Cisco 7604 | Processor Guide - Page 59
    Chapter 3 Installing and Configuring Route Switch Processors and Supervisor Engines Upgrading DIMMs on RSP720 router#show module 1 Mod Ports Card Type Serial No 1 2 Route Switch Processor 720 (Active) RSP720-3CXL-GE Model SAL15077HPS Mod MAC addresses Hw Fw Sw Status 1 c89c.1dfa.
  • Cisco 7604 | Processor Guide - Page 60
    remove the RSP from the chassis for DIMM upgrade. Save all your configurations before you remove the RSP. Caution Always use an ESD wrist strap when handling the RSP or coming in contact with internal components. 3-16 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL
  • Cisco 7604 | Processor Guide - Page 61
    1 GB DIMM from slot 1. Install the new 2 GB DIMM in slot 1. Remove the 1 GB DIMM from slot 2 (if present). Install another 2 GB DIMM in slot 2. Configuring a Supervisor Engine or Route Switch Processor See the Cisco 7600 Series Router Cisco IOS Software Configuration Guide for information about how
  • Cisco 7604 | Processor Guide - Page 62
    Configuring a Supervisor Engine or Route Switch Processor Chapter 3 Installing and Configuring Route Switch Processors and Supervisor Engines 3-18 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7604 | Processor Guide - Page 63
    6000W Power supply output fails. The green LED indicates the DC power supply for all the power inputs. For more information on the various LED status, Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide at http://www.cisco.com/en/US/docs/routers/7600/Hardware/Hardware_Guides
  • Cisco 7604 | Processor Guide - Page 64
    -1GE Unsupported Hardware and Features These hardware and features are not supported by the RSP720: • Unsupported chassis: Cisco 7603. • Unsupported modules: Optical Service Modules (OSMs), FlexWAN module. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 4-2 OL-10100
  • Cisco 7604 | Processor Guide - Page 65
    following chassis and modules: • Cisco 7603, 7606, and 7613 chassis. • Services modules, Optical Service Modules (OSMs), FlexWAN module. • RSP720-10GE does not support High Availability features in 12.2(33)SRC and 12.2(33)SRD. Obtaining Technical Assistance If you are unable to solve a problem on
  • Cisco 7604 | Processor Guide - Page 66
    for supervisor issues. Table 4-2 Troubleshooting Supervisor Failure Problem Supervisor fails to operate or power up Supervisor dual in-line memory module (DIMM) detection issue RSP720 DIMM upgrade issues Solution 1. Ensure that the card is inserted firmly in the slot. 2. Ensure that you have
  • Cisco 7604 | Processor Guide - Page 67
    of a route processor. Table 4-3 Troubleshooting back-plane data corruption Problem Back-plane data corruption when cards are partially inserted Solution 1. Ensure that the redundant supervisor is operational. 2. Ensure that the removed supervisor is reinserted into the chassis. Note Though
  • Cisco 7604 | Processor Guide - Page 68
    ) 7600(config)#power enable module 4 *Feb 22 09:39:23.071: %DIAG-SP-6-BYPASS: Module 4: Diagnostics is bypassed *Feb 22 09:39:25.622: %OIR-SP-6-INSCARD: Card inserted in slot 4, interfaces are now online Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 4-6 OL-10100
  • Cisco 7604 | Processor Guide - Page 69
    Chapter 4 Troubleshooting Route Switch Processors and Supervisor Engines Troubleshooting Line Card Module Troubleshooting Interface Down Issues Table 4-4 lists the solutions for a interface issues. Table 4-5 Troubleshooting Interface Issues Problem Wrong or faulty cable Clocking not
  • Cisco 7604 | Processor Guide - Page 70
    sup-image:0 (Unknown error 0) Ensure that you don't have a very large image loaded on the 7600 to begin with, which may cause resource problems. The solution is to load a default image first and then do reload netboot. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7604 | Processor Guide - Page 71
    . shtml • Hardware Requirements for Catalyst 6000/Catalyst 6500 Redundancy at the following URL: http://www.cisco.com/en/US/products/hw/switches/ps700/products_tech_note09186a00800a2cee. shtml OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 4-9
  • Cisco 7604 | Processor Guide - Page 72
    Troubleshooting Supervisor 2T Chapter 4 Troubleshooting Route Switch Processors and Supervisor Engines 4-10 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7604 | Processor Guide - Page 73
    specifications for the Cisco 7600 route switch processors and supervisor engines. Module Specifications Table A-1 lists the environmental and physical specifications for the Cisco 7600 route switch processors (RSPs Physical Characteristics Dimensions (H x W x D) Weight Specification 32 to 104
  • Cisco 7604 | Processor Guide - Page 74
    Regulatory Standards Compliance Appendix A Technical Specifications Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide A-2 OL-10100-11
  • Cisco 7604 | Processor Guide - Page 75
    Transceiver Modules, page B-5 • Console Port Cabling Specifications and Pinouts, page B-10 • RJ-45 Connector, page B-14 • Fiber-Optic Connectors, page B-16 • LX/LH GBIC and MMF Cable Considerations, page B-19 OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7604 | Processor Guide - Page 76
    Optics Appendix B Cable and Connector Specifications Supported Dense Wave Division Multiplexing (DWDM) Wavelength Optics Table B-1 lists the DWDM small form-factor pluggables (SFP) to RSP 720 and RSP 720-10GE: Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-2 OL
  • Cisco 7604 | Processor Guide - Page 77
    Cable and Connector Specifications Supported Dense Wave Division Multiplexing (DWDM) Wavelength Optics Table B-1 Supported DWDM Wavelength Optics Supervisor Engine or RSP RSP720 and RSP720-10GE Transceiver Module 11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-3
  • Cisco 7604 | Processor Guide - Page 78
    Table B-2 Supported CWDM Wavelength Optics Supervisor Engine or RSP RSP720 and RSP720-10GE Transceiver Module Part Numbers CWDM-SFP-1470 CWDM-SFP-1490 CWDM-SFP-1510 CWDM-SFP-1530 CWDM-SFP-1550 CWDM-SFP-1570 CWDM-SFP-1590 CWDM-SFP-1610 Cisco 7600 Series Router Supervisor Engine and Route Switch
  • Cisco 7604 | Processor Guide - Page 79
    pluggable (SFP) modules, X2 modules, XENPAK modules, and Gigabit Interface Converter (GBIC) modules. Table B-3 lists the orderable part numbers for supported transceiver modules. In addition, the following tables provide information about the modules and their cabling specifications: • Table B-4 and
  • Cisco 7604 | Processor Guide - Page 80
    transceiver modules that are used for Cisco 7600 uplink ports. Table B-5 provides cabling specifications. Note Use Category 5 Shielded Twisted Pair cable at the port that supports the10/100/1000-Mbps RJ-45 connector for the RSP720-10GE. Cisco 7600 Series Router Supervisor Engine and Route Switch
  • Cisco 7604 | Processor Guide - Page 81
    DOM support (NEBS 3ESD); 10/100/1000-Mbps RJ-45 connector Table B-5 lists the cabling specifications for the 1GE uplink ports, which are located on SFP transceiver modules that plug into the front panel. Table B-5 1GE Cabling Specifications SFP Module (Product ID) GLC-SX-MM SFP-GE-S Wavelength
  • Cisco 7604 | Processor Guide - Page 82
    X2 or XENPAK transceiver module for CX4 copper cable, Infiniband 4X connector 10GBASE-LRM X2 transceiver module for MMF, dual SC connector Cisco 10GBASE-ZR X2 transceiver module for SMF, dual SC connector Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-8 OL-10100-11
  • Cisco 7604 | Processor Guide - Page 83
    Gigabit Interface Converter (GBIC) modules installed in the Supervisor Engine 2. All GBIC interfaces have SC connectors, and the minimum cable distance for all GBICs listed (MMF and SMF) is 6.5 feet (2 meters). OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7604 | Processor Guide - Page 84
    installed at each end of the link. Without attenuators, the minimum link distance is 24.9 miles (40 km). Console Port Cabling Specifications and Pinouts The console port, which is located on the front panel of the supervisor engine or route switch processor, provides access to the Cisco 7600 router
  • Cisco 7604 | Processor Guide - Page 85
    8 is white on the other (a rollover cable reverses pins 1 and 8, 2 and 7, 3 and 6, and 4 and 5). Figure B-1 Identifying a Rollover Cable Pin 1 Pin 1 and pin 8 should be the same color Pin 8 H3824 OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-11
  • Cisco 7604 | Processor Guide - Page 86
    Port Cabling Specifications and Pinouts Appendix B Cable and Connector Specifications DB-9 Adapter (for Connecting to a PC) Use the RJ-45-to-RJ-45 rollover cable Signal CTS DSR RxD GND GND TxD DTR RTS B-12 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7604 | Processor Guide - Page 87
    Cable and Connector Specifications Console Port Cabling Specifications and Pinouts Modem Adapter Use the RJ-45-to-RJ-45 rollover cable III console cable and adapter (not provided). For instructions, see OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-13
  • Cisco 7604 | Processor Guide - Page 88
    -immunity requirements, you must use foil-twisted pair (FTP) cable that is properly grounded at both ends. Inline power for IP phones uses connector pins 1, 2, 3, and 6 in a Category 5, Category 5e, or Category 6 cable to transmit power (6.3 W) from the router. This method of supplying power is
  • Cisco 7604 | Processor Guide - Page 89
    B-4 Switch 1 TP0+ 2 TP03 TP1+ 6 TP1- Twisted-Pair Crossover 1000BASE-T Cable Schematic Switch 1 TP0+ 2 TP03 TP1+ 6 TP1- 4 TP2+ 5 TP27 TP3+ 8 TP3- 4 TP2+ 5 TP27 TP3+ 8 TP3- 65274 RJ-45 Connector OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-15
  • Cisco 7604 | Processor Guide - Page 90
    to prevent contamination. Always clean fiber connectors before installing them. For fiber-optic connector cleaning instructions, see the "Cleaning the Fiber-Optic Connectors" section on page B-18. B-16 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7604 | Processor Guide - Page 91
    on the Supervisor Engine 720, Route Switch Processor 720, and RSP720-10GE uplink ports use either MT-RJ connectors or LC connectors depending on the SFP module vendor. Figure B-7 shows an LC connector. OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-17
  • Cisco 7604 | Processor Guide - Page 92
    installing them. For fiber-optic connector cleaning instructions, see the "Cleaning the Fiber-Optic Connectors" section on page B-18. When you disconnect the fiber-optic cable from the module procedure. B-18 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7604 | Processor Guide - Page 93
    chassis. required. You must install the patch cord (Cisco product number CAB-GELX-625 or equivalent) between the GBIC and the MMF cable Configuration Example Figure B-8 shows a typical patch cord configuration. OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7604 | Processor Guide - Page 94
    "To Cable Plant" into the patch panel. The patch cord is 9.84 feet (3 meters) long and has duplex SC male connectors at each end. Figure B-9 Patch Cord Installation To equipment To cable plant 13089 B-20 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100
  • Cisco 7604 | Processor Guide - Page 95
    14 OL-10100-11 INDEX Cisco 7600 series router features 3 overview 1 commands copy running-config 7 write 7 CompactFlash and MicroDrive support 13 CompactFlash cards front-panel slot 15, 22, 12 installing 13 removing 14 connecting modem 10 terminal to supervisor engine or RSP 9 to console port 9 to
  • Cisco 7604 | Processor Guide - Page 96
    Cisco 7600 series router components 6 modules 8 supervisor engines and RSPs 8 http //www.cisco.com/en/US/docs/ios/ha/command/refere nce/ha_book.html 12 //www.cisco.com/en/US/docs/ios/qos/command/refer ence/qos_book.html 13 I installing flash memory cards 13 modules 4 patch cord 20 interfaces
  • Cisco 7604 | Processor Guide - Page 97
    ESD damage 2 PWR MGMT LED Sup Eng 2 25 Sup Eng 720, Sup Eng 32 16, 23 Q QoS, RSP720-10GE 13 R redundancy 4 removing flash memory cards 14 modules 7 Reset button 15, 22 RJ-45 connectors 14 rollover cable 11 router, managing 6 route switch processor 7 CompactFlash support 13 connecting to 9, 10 hot
  • Cisco 7604 | Processor Guide - Page 98
    720 (RSP720-10GE) CompactFlash support 12 RSP720-10GE 11 RSP720-10GE, QoS 13 S SC connector 16 slot numbers 6 specifications, cabling 1 specifications, environmental and physical (table) 1 STATUS LED Sup Eng 2 24 Sup Eng 720, Sup Eng 32 16, 22 supervisor engine CompactFlash support 13 configuration
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Cisco 7600 Series Router
Supervisor Engine and
Route Switch Processor Guide
March 2012
Text Part Number: OL-10100-11