Cisco 7606 Processor Guide

Cisco 7606 Manual

Get Cisco 7606 PDF manuals and user guides View all Cisco 7606 manuals
Add to My Manuals
Save this manual to your list of manuals

Cisco 7606 manual content summary:

  • Cisco 7606 | Processor Guide - Page 1
    Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide March 2012 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-10100-11
  • Cisco 7606 | Processor Guide - Page 2
    Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide Copyright © 2006
  • Cisco 7606 | Processor Guide - Page 3
    1-3 Port Addresses 1-6 Physical Interface Addresses 1-6 MAC Addresses 1-7 Supervisor Engine 2T 1-8 Supported Hardware 1-8 Features 1-8 Port Addresses 1-8 Route Switch Processors and Supervisor Engines 2-1 Overview 2-2 Route Switch Processor 720 2-9 RSP720 Features 2-9 Supported Chassis, Line Cards
  • Cisco 7606 | Processor Guide - Page 4
    Feature Support 3-14 Upgrading DIMMs on RSP720 3-14 Configuring a Supervisor Engine or Route Switch Processor 3-17 Troubleshooting Route Switch Processors and Supervisor Engines 4-1 Getting Started 4-1 AC and DC Power Supply Information 4-1 Chassis and Supervisor Slot Installation 4-2 Cisco 7600
  • Cisco 7606 | Processor Guide - Page 5
    Assistance 4-3 Troubleshooting Supervisor Failures 4-4 Troubleshooting Back-Plane Data Corruption During OIR of a RP 4-5 Troubleshooting Chassis Overheat Conditions 4-5 Troubleshooting Line Card Module 4-5 Troubleshooting Interface Down Issues 4-7 Traceback Decode Procedure 4-7 Troubleshooting Image
  • Cisco 7606 | Processor Guide - Page 6
    -RJ Connectors B-17 LC Connectors B-17 Cleaning the Fiber-Optic Connectors B-18 LX/LH GBIC and MMF Cable Considerations B-19 Patch Cord B-19 Patch Cord Configuration Example B-19 Patch Cord Installation B-20 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide vi OL-10100-11
  • Cisco 7606 | Processor Guide - Page 7
    Preface This guide describes the route switch processors and supervisor engines supported by Cisco 7600 series routers. It also provides technical specifications for these modules and describes cable and connector specifications. Caution Only trained and qualified service personnel (as defined in
  • Cisco 7606 | Processor Guide - Page 8
    interface and port addresses. Describes the route switch processors (RSPs) and supervisor engines supported on Cisco 7600 series routers. Provides instructions for installing and removing RSPs and supervisor engines and connecting to the console and uplink ports. Cisco 7600 Series Router Supervisor
  • Cisco 7606 | Processor Guide - Page 9
    INSTRUCTIONS See Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers for translations of warnings and information about the compliance and safety standards with which Cisco 7600 series routers conform. OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route
  • Cisco 7606 | Processor Guide - Page 10
    -7609) • Cisco 7600 Series Router Module Installation Guide • Cisco 7600 Series Router Cisco IOS Command Reference • Cisco 7600 Series Router Cisco IOS System Message Guide • Cisco 7600 Series Router Cisco IOS Software Configuration Guide Documentation for the Cisco 7600 series router is available
  • Cisco 7606 | Processor Guide - Page 11
    interface and port addresses on the routers. It contains the following sections: • Cisco 7600 Series Routers, page 1-1 • Port Addresses, page 1-6 • Supervisor Engine 2T, page 1-8 Note This document does not contain instructions for installing the router. For instructions on how to install the router
  • Cisco 7606 | Processor Guide - Page 12
    fan assembly • Redundant AC-input or DC-input power supplies • Redundant AC-input or DC-input power entry modules (PEMs) (Cisco 7603 and Cisco 7606 routers only) • An optional Switch Fabric Module (WS-X6500-SFM2) that is available with the Supervisor Engine 2. For redundancy, you can install
  • Cisco 7606 | Processor Guide - Page 13
    engine or route switch processor Description For detailed information about the features supported on Cisco 7600 series routers, see the Cisco 7600 Series Router Cisco IOS Software Configuration Guide for the version of software being used on the router. • Modular, upgradable feature modules
  • Cisco 7606 | Processor Guide - Page 14
    ) supervisor engines or route switch and redundancy processors, including fast switchover to the redundant (standby) module • Support for two redundant AC- or DC-input, load-sharing power supplies • Support for two redundant AC- or DC-input PEMs (Cisco 7603 and Cisco 7606 routers only) • Power
  • Cisco 7606 | Processor Guide - Page 15
    Memory components Description • Electrically erasable programmable read-only memory (EEPROM) on the supervisor engine or route switch processor stores module-specific information, such as the serial number, part number, controller type, hardware revision, configuration information, and other
  • Cisco 7606 | Processor Guide - Page 16
    number on the module. Port numbers always begin at 1 (n/1, n/2, and so on). - On horizontal-oriented modules, ports are numbered from left to right. - On vertical-oriented modules, ports are numbered from top to bottom. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7606 | Processor Guide - Page 17
    one unique MAC address. This addressing scheme enables the router to identify the state (connected or not connected) of each interface. When you hot swap a module, the MAC address changes with the module. OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 1-7
  • Cisco 7606 | Processor Guide - Page 18
    , data centers, and service provider networks. Some of the primary features for Supervisor Engine 2T include: • Platform scalability: Delivering up to 80 Gbps per slot of switching capacity on the 7609-S chassis; 2-Terabit aggregate bandwidth capacity. Providing 1Gbps/10Gbps and 40Gbps interface
  • Cisco 7606 | Processor Guide - Page 19
    the route switch processors and supervisor engines supported on Cisco 7600 series routers and provides instructions for performing basic tasks on the modules. It contains the following sections: • Overview, page 2-2 • Route Switch Processor 720, page 2-9 • RSP720 with 10GE Uplink Ports, page
  • Cisco 7606 | Processor Guide - Page 20
    and supervisor engines: • Route Switch Processor 720-Supported on all chassis (including enhanced) except the Cisco 7603 router and the Cisco OSR-7609. Available in Cisco IOS Release 12.2SRB and later releases. • RSP720-10GE (with 10GE uplink ports)-Supported on the Cisco 7604 and 7609 routers and
  • Cisco 7606 | Processor Guide - Page 21
    (STP) and others. For information about supported protocols, see the Cisco 7600 Series Router Cisco IOS Software Configuration Guide and the release notes for the software version running on the router. OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-3
  • Cisco 7606 | Processor Guide - Page 22
    CompactFlash to 1 GB) • Requires larger power supplies and a high-speed fan tray • QoS port architecture, 10GE ports (Rx/Tx): 8q8t/1p7q8t (CoS) • QoS port architecture, 1GE ports (Rx/Tx): 2q8t/1p3q8t Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-4 OL-10100-11
  • Cisco 7606 | Processor Guide - Page 23
    to 1 GB) and two internal CompactFlash slots (one each for RP and SP, 512 MB default for each) • Requires larger power supplies and a high-speed fan tray • QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-5
  • Cisco 7606 | Processor Guide - Page 24
    CompactFlash Type II slots • Requires larger power supplies and a high-speed fan tray • QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t Note To run Release SRE/15.0(1)S, SUP720 requires a minimum of 1 GB DRAM. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-6 OL-10100
  • Cisco 7606 | Processor Guide - Page 25
    , and 64-MB bootflash; high-capacity PFC3BXL allows routing and forwarding processes to be offloaded from the supervisor engine to the PFC (see note below) • Two CompactFlash Type II slots • Requires larger power supplies and a high-speed fan tray • QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t
  • Cisco 7606 | Processor Guide - Page 26
    of flashs support 4Gb and 8Gb memory. • QOS settings when the uplink ports are in different mode: - 10G only COS-Q: RX: 8q4t; TX:1p7q4t - Mixed: COS-Q: RX: 2q4t; TX:1p3q4t - 1GE only : DSCP-Q : RX :8q4t, TX :1p7q4t Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-8 OL
  • Cisco 7606 | Processor Guide - Page 27
    . The switch processor (SP) ships with a default 1-GB memory. Memory options are available to upgrade to 4-GB memory on the RP. From Cisco IOS Release 12.2(33)SRD1 onwards, a 2-GB memory upgrade option is supported on the SP. OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch
  • Cisco 7606 | Processor Guide - Page 28
    2 Route Switch Processors and Supervisor Engines Supported Chassis, Line Cards, and Modules The RSP720 supports the following Cisco 7600 chassis, line cards and modules: • Supported on all Cisco 7600 routers (including enhanced chassis) except the Cisco 7603 and the Cisco OSR-7609 • SPA interface
  • Cisco 7606 | Processor Guide - Page 29
    10GE. Supported Chassis, Line Cards, and Modules The RSP720-10GE supports the following chassis and modules: • Supported on the Cisco 7604 and 7609 chassis and the Cisco 7603-S, 7606-S, and 7609-S chassis OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-11
  • Cisco 7606 | Processor Guide - Page 30
    exists because the uplink ports must perform lookups on the active RSP, which is not possible in RPR mode. • Intelligent Service Gateway is not supported. • Device authentication to prevent counterfeiting Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7606 | Processor Guide - Page 31
    RSP720, Cisco IOS software boots up but the software detects a mismatch and enters ROMMON mode. • You can configure the RSP720-10GE to run QoS features on all uplink ports (10GE and 1GE) or on 10GE ports only. A new CLI command (mls qos supervisor 10g-only) is available to configure the module to
  • Cisco 7606 | Processor Guide - Page 32
    You can shut down all three 1GE uplink ports before entering the mls qos supervisor 10g-only command. If you do not shut down the ports first, the mls qos supervisor 10g-only command shuts down the ports. 2-14 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7606 | Processor Guide - Page 33
    fabric that enables 80 Gbps switching capacity per slot on 7609-S chassis. The forwarding engine on Supervisor Engine 2T is capable of delivering high-performance forwarding for Layer 2 and Layer 3 services. Supervisor Engine 2T delivers many new hardware-enabled innovations in the areas of security
  • Cisco 7606 | Processor Guide - Page 34
    slot-no led beacon command to configure the LED. All chassis environmental monitors are reporting OK. The module is powering up or a minor hardware fault has occurred. Major hardware problem. The temperature of the supervisor engine has exceeded the major temperature threshold. Continuous backplane
  • Cisco 7606 | Processor Guide - Page 35
    IPv6 routing L2 bridging VS-S2T-10G In hardware Up to 720 Mpps** In hardware Up to 390 Mpps** In hardware Up to 720 Mpps** VS-S2T-10G-XL In hardware Up to 720 Mpps** In hardware Up to 390 Mpps** In hardware Up to 720 Mpps** OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch
  • Cisco 7606 | Processor Guide - Page 36
    Supervisor Engine 2T Chapter 2 Route Switch Processors and Supervisor Engines Name MPLS VLAN Bridge domains VS-S2T-10G VS-S2T-10G-XL MPLS in hardware to enable use of Layer 3 VPNs and EoMPLS tunneling. Up to 8192 VRFs with a total of up to 256K1 forwarding entries per system. MPLS in hardware
  • Cisco 7606 | Processor Guide - Page 37
    Chapter 2 Route Switch Processors and Supervisor Engines Supervisor Engine 2T OL-10100-11 Feature Packet or byte policers Per port per VLAN VS-S2T-10G Yes Yes VS-S2T-10G-XL Yes Yes Table 2-6 shows security features and scalability for Supervisor Engine 2T. Table 2-6 Security Features and
  • Cisco 7606 | Processor Guide - Page 38
    support Yes VPN aware NAT Yes VRF-lite scalability VLAN reuse per sub-interface Per VPN interface statistics Yes VS-S2T-10G-XL Yes Yes Yes Yes Yes Yes Yes Yes Yes 16k Yes Yes Yes Yes Yes VLAN reuse per sub-interface Yes 2-20 Cisco 7600 Series Router Supervisor Engine and Route Switch
  • Cisco 7606 | Processor Guide - Page 39
    II slot Link Status LEDs USB ports Front-Panel Controls (RSP720, RSP720-10GE, Sup720, Sup32) Table 2-8 describes the front-panel controls on the Route Switch Processor 720 and RSP720-10GE, the Supervisor Engine 720, and the Supervisor Engine 32. OL-10100-11 Cisco 7600 Series Router Supervisor
  • Cisco 7606 | Processor Guide - Page 40
    . The module is powering up or a minor hardware fault has occurred. Major hardware problem. The temperature of the supervisor engine or RSP has exceeded the major temperature threshold. Continuous backplane stall. 2-22 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL
  • Cisco 7606 | Processor Guide - Page 41
    available for all modules installed in the router. Orange The supervisor engine or RSP is powering up or has minor hardware problems. Red Major hardware problem. DISK Green The disk is active. Do not remove the disk while the light is on or the file may be corrupted. LINK Green The port
  • Cisco 7606 | Processor Guide - Page 42
    2 Route Switch Processors and Supervisor Engines Table 2-10 Supervisor Engine 2 Front-Panel Controls Component Status LEDs Reset Button Console Port Console Port Mode Switch PCMCIA Slot and LED Switch Load Meter Uplink Ports Description Indicate the status of various functions on the module (see
  • Cisco 7606 | Processor Guide - Page 43
    The VTT module terminates signals on the system switching bus. 3. If no redundant supervisor engine is installed and there is a VTT module minor or major overtemperature condition, the system shuts down. OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-25
  • Cisco 7606 | Processor Guide - Page 44
    Supervisor Engine 2 Chapter 2 Route Switch Processors and Supervisor Engines 2-26 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7606 | Processor Guide - Page 45
    chassis slot to install the module in. (See the "Determining Module Location" section on page 3-3.) • Consider cabling for the console and uplink ports. (See Appendix B, "Cable and Connector Specifications.") OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7606 | Processor Guide - Page 46
    3 Installing and Configuring Route Switch Processors and Supervisor Engines Safety Precautions for Module Installation and Removal Be sure to observe the following warnings and safety precautions when you work on the router. Warning Hazardous voltage or energy is present on the backplane when
  • Cisco 7606 | Processor Guide - Page 47
    chassis) • Not supported in the 3-slot chassis • Slots 1 and 2 (3-slot and 4-slot chassis) • Slots 5 and 6 (6-slot and 9-slot chassis) • Slots 7 and 8 (13-slot chassis) • Slots 5 and 6 (9 slot 7609-S chassis). OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7606 | Processor Guide - Page 48
    slot and 9-slot chassis) • Slots 7 and 8 (13-slot chassis) • Not supported in the 3-slot chassis • Slots 1 and 2 (all chassis) • Not supported in the 4-slot chassis Installing a Supervisor Engine or Route Switch Processor To install a supervisor engine or route switch processor module in the router
  • Cisco 7606 | Processor Guide - Page 49
    Chapter 3 Installing and Configuring Route Switch Processors and Supervisor Engines Installing a Supervisor Engine or Route Switch Processor Figure 3-1 Ejector Levers and Captive Installation Screws OSM-4OC12-POS-MM 1 STATUS 2 4 PORT OC-12 POS MM LINK 1 2 LINK 3 4 LINK 3 4 LINK RESET
  • Cisco 7606 | Processor Guide - Page 50
    installation screws. Note Blank module filler plates (Cisco part number 800-00292-01) should be installed in any empty chassis slots to keep dust out of the chassis and to maintain consistent airflow through the chassis. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7606 | Processor Guide - Page 51
    by downloading it from the server to the nonvolatile memory of the supervisor engine or RSP. If the module is running Cisco IOS software, save the current running configuration by entering the copy running-config startup-config command. Warning Hazardous voltage or energy is present on the backplane
  • Cisco 7606 | Processor Guide - Page 52
    Installing and Configuring Route Switch Processors and Supervisor Engines Hot Swapping (OIR) Modules Cisco 7600 series routers provide a feature that allows you to remove and replace a redundant supervisor engine or route switch processor (and other redundant cards) without powering down the router
  • Cisco 7606 | Processor Guide - Page 53
    port on a route switch processor or supervisor engine. You must connect to the router through the console port to configure the router for the first time. You can also connect to the console port to perform diagnostics and troubleshoot problems on the router. For console cabling specifications
  • Cisco 7606 | Processor Guide - Page 54
    to the Uplink Ports The supervisor engine and route switch processor have uplink ports that you use to connect the router to other network devices. You can configure the ports with small form-factor pluggable (SFP), XENPAK, X2, or Gigabit Interface Converter (GBIC) optics modules. Table 3-2 lists
  • Cisco 7606 | Processor Guide - Page 55
    to the Uplink Ports Table 3-2 Route Switch Processor and Supervisor Engine Uplink Ports Module Route Switch Processor 720 RSP720-10GE Uplink Ports Two 10/100/1000 BASE-T Gigabit Ethernet uplink ports: • Port 1 requires that a 1-Gbps SFP module be installed. • Port 2 supports either a 1-Gbps SFP
  • Cisco 7606 | Processor Guide - Page 56
    like any other ports in the chassis. • In Cisco IOS Release 12.2SRC, the uplink ports on a standby RSP720-10GE are not active and cannot be used for normal traffic. Using Flash Memory Cards The front panel on the supervisor engine or route switch processor has one or two disk slots for flash memory
  • Cisco 7606 | Processor Guide - Page 57
    3 Installing and Configuring Route Switch Processors and Supervisor Engines Using Flash Memory Cards Note Not all flash memory cards have a write-protection switch. Table 3-3 lists the Cisco product numbers of memory cards supported on Cisco 7600 supervisor engines and route switch processors
  • Cisco 7606 | Processor Guide - Page 58
    you required for upgrade. If the version of the 7600-MSFC4 card is 4.0 and above, then you have to order SO-DIMM. If the version is below 4.0, then you have to order MINI-DIMM. Refer the sample output of the command below: 3-14 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor
  • Cisco 7606 | Processor Guide - Page 59
    Chapter 3 Installing and Configuring Route Switch Processors and Supervisor Engines Upgrading DIMMs on RSP720 router#show module 1 Mod Ports Card Type Serial No 1 2 Route Switch Processor 720 (Active) RSP720-3CXL-GE Model SAL15077HPS Mod MAC addresses Hw Fw Sw Status 1 c89c.1dfa.
  • Cisco 7606 | Processor Guide - Page 60
    on RP You have to remove the RSP from the chassis for DIMM upgrade. Save all your configurations before you remove the RSP. Caution Always use an ESD wrist strap when handling the RSP or coming in contact with internal components. 3-16 Cisco 7600 Series Router Supervisor Engine and Route Switch
  • Cisco 7606 | Processor Guide - Page 61
    slot 1. Remove the 1 GB DIMM from slot 2 (if present). Install another 2 GB DIMM in slot 2. Configuring a Supervisor Engine or Route Switch Processor See the Cisco 7600 Series Router Cisco IOS Software Configuration Guide for information about how to configure the supervisor engine or route switch
  • Cisco 7606 | Processor Guide - Page 62
    Configuring a Supervisor Engine or Route Switch Processor Chapter 3 Installing and Configuring Route Switch Processors and Supervisor Engines 3-18 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7606 | Processor Guide - Page 63
    : • Power supplies are supplying adequate power to the system. • The system fan assembly is operating normally. • System software boots successfully. • The supervisor engine and all switching modules are initialized and installed properly in their slots. AC and DC Power Supply Information AC power
  • Cisco 7606 | Processor Guide - Page 64
    7606S 7609 7609S 7613 Table 4-1 Chassis and Supervisor Slot Installation Designated Supervisor Slots 1, 2 1, 2 5, 6 5, 6 5, 6 5, 6 7, 8 RSP720-1GE Supported Hardware and Features The RSP720 supports the following Cisco 7600 chassis, line cards and modules: • Supported on all Cisco 7600 routers
  • Cisco 7606 | Processor Guide - Page 65
    Route Switch Processors and Supervisor Engines RSP720-10GE Supported Chassis, Line Cards, and Modules RSP720-10GE Supported Chassis, Line Cards, and Modules The RSP720-10GE supports the following chassis and modules: • Cisco 7604 and 7609 chassis and the Cisco 7603-S, 7606-S, and 7609-S chassis
  • Cisco 7606 | Processor Guide - Page 66
    you insert the both the new 2 DIMMs in slot 1 and slot 2. 4. If you insert the DIMMs in both the slots for RP upgrade, and card does not initiate, then swap the DIMMs between the two slots and check again. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 4-4 OL-10100-11
  • Cisco 7606 | Processor Guide - Page 67
    impaired state, the card may ultimately need to be reset, but some minimal data should be collected before reloading the card. Before reloading a line card, capture the following CLI data to a text file. ! OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 4-5
  • Cisco 7606 | Processor Guide - Page 68
    in slot 4 set off (admin request) 7600(config)#power enable module 4 *Feb 22 09:39:23.071: %DIAG-SP-6-BYPASS: Module 4: Diagnostics is bypassed *Feb 22 09:39:25.622: %OIR-SP-6-INSCARD: Card inserted in slot 4, interfaces are now online Cisco 7600 Series Router Supervisor Engine and Route Switch
  • Cisco 7606 | Processor Guide - Page 69
    Chapter 4 Troubleshooting Route Switch Processors and Supervisor Engines Troubleshooting Line Card Module Troubleshooting Interface Down Issues Table 4-4 lists the solutions for a interface issues. Table 4-5 Troubleshooting Interface Issues Problem Wrong or faulty cable Clocking not
  • Cisco 7606 | Processor Guide - Page 70
    Troubleshooting Line Card Module Chapter 4 Troubleshooting Route Switch Processors and Supervisor Engines It is important to decode the traceback message while filing DDTS. To decode a traceback symbol, files of the corresponding image is required. A c7600 image has a set of symbol files like RP
  • Cisco 7606 | Processor Guide - Page 71
    , see the following documents: • Troubleshooting Switch Port and Interface Problems at the following URL: http://www.cisco.com/en/US/products/hw/switches/ps708/products_tech_note09186a008015bfd6. shtml • How to Determine the Type of Supervisor Module That Is Installed in Catalyst 6500/6000 Series
  • Cisco 7606 | Processor Guide - Page 72
    Troubleshooting Supervisor 2T Chapter 4 Troubleshooting Route Switch Processors and Supervisor Engines 4-10 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7606 | Processor Guide - Page 73
    7600 route switch processors and supervisor engines. Module Specifications Table A-1 lists the environmental and physical specifications for the Cisco 7600 route switch processors (RSPs) and supervisor engines. Table A-1 Environmental and Physical Specifications Item Environmental Temperature
  • Cisco 7606 | Processor Guide - Page 74
    Regulatory Standards Compliance Appendix A Technical Specifications Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide A-2 OL-10100-11
  • Cisco 7606 | Processor Guide - Page 75
    Transceiver Modules, page B-5 • Console Port Cabling Specifications and Pinouts, page B-10 • RJ-45 Connector, page B-14 • Fiber-Optic Connectors, page B-16 • LX/LH GBIC and MMF Cable Considerations, page B-19 OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7606 | Processor Guide - Page 76
    Appendix B Cable and Connector Specifications Supported Dense Wave Division Multiplexing (DWDM) Wavelength Optics Table B-1 lists the DWDM small form-factor pluggables (SFP) to RSP 720 and RSP 720-10GE: Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-2 OL-10100-11
  • Cisco 7606 | Processor Guide - Page 77
    Specifications Supported Dense Wave Division Multiplexing (DWDM) Wavelength Optics Table B-1 Supported DWDM Wavelength Optics Supervisor Engine or RSP RSP720 and RSP720-10GE Transceiver Module Part Numbers -10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-3
  • Cisco 7606 | Processor Guide - Page 78
    Supported CWDM Wavelength Optics Supervisor Engine or RSP RSP720 and RSP720-10GE Transceiver Module Part Numbers CWDM-SFP-1470 CWDM-SFP-1490 CWDM-SFP-1510 CWDM-SFP-1530 CWDM-SFP-1550 CWDM-SFP-1570 CWDM-SFP-1590 CWDM-SFP-1610 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor
  • Cisco 7606 | Processor Guide - Page 79
    supervisor engine or route switch processor provide the uplink ports for the router. Several types of transceiver modules are available: small form-factor pluggable (SFP) modules, X2 modules, XENPAK modules, and Gigabit Interface Converter (GBIC) modules. Table B-3 lists the orderable part numbers
  • Cisco 7606 | Processor Guide - Page 80
    transceiver modules that are used for Cisco 7600 uplink ports. Table B-5 provides cabling specifications. Note Use Category 5 Shielded Twisted Pair cable at the port that supports the10/100/1000-Mbps RJ-45 connector for the RSP720-10GE. Cisco 7600 Series Router Supervisor Engine and Route Switch
  • Cisco 7606 | Processor Guide - Page 81
    temperature range and DOM support (NEBS 3ESD); 10/100/1000-Mbps RJ-45 connector Table B-5 lists the cabling specifications for the 1GE uplink ports, which are located on SFP transceiver modules mi (10 km) OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-7
  • Cisco 7606 | Processor Guide - Page 82
    X2 or XENPAK transceiver module for CX4 copper cable, Infiniband 4X connector 10GBASE-LRM X2 transceiver module for MMF, dual SC connector Cisco 10GBASE-ZR X2 transceiver module for SMF, dual SC connector Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-8 OL-10100-11
  • Cisco 7606 | Processor Guide - Page 83
    Gigabit Interface Converter (GBIC) modules installed in the Supervisor Engine 2. All GBIC interfaces have SC connectors, and the minimum cable distance for all GBICs listed (MMF and SMF) is 6.5 feet (2 meters). OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7606 | Processor Guide - Page 84
    installed at each end of the link. Without attenuators, the minimum link distance is 24.9 miles (40 km). Console Port Cabling Specifications and Pinouts The console port, which is located on the front panel of the supervisor engine or route switch processor, provides access to the Cisco 7600 router
  • Cisco 7606 | Processor Guide - Page 85
    Pinouts The Cisco 7600 series router is shipped with an accessories kit that contains the cable and adapters you need to connect a console (an ASCII terminal or PC running terminal emulation software) or modem to the console port on the front panel of the supervisor engine or route switch processor
  • Cisco 7606 | Processor Guide - Page 86
    to Pin 8. RJ-45-to-DB-25 Terminal Adapter DB-25 Pin 5 6 3 7 7 2 20 4 Console Device Signal CTS DSR RxD GND GND TxD DTR RTS B-12 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7606 | Processor Guide - Page 87
    Port Console Device Pin (Signal Name) 1 (RTS)1 Input/Output Output 2 (DTR) Output 3 (RxD) Input 4 (GND) GND 5 (GND) GND 6 (TxD) Output 7 (DSR) 8 (CTS)1 Input Input 1. Pin 1 is connected internally to Pin 8. OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch
  • Cisco 7606 | Processor Guide - Page 88
    module. Caution To comply with Telcordia GR-1089 intrabuilding, lightning-immunity requirements, you must use foil-twisted pair (FTP) cable that is properly grounded at both ends. Inline power for IP ) B-14 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7606 | Processor Guide - Page 89
    B-4 Switch 1 TP0+ 2 TP03 TP1+ 6 TP1- Twisted-Pair Crossover 1000BASE-T Cable Schematic Switch 1 TP0+ 2 TP03 TP1+ 6 TP1- 4 TP2+ 5 TP27 TP3+ 8 TP3- 4 TP2+ 5 TP27 TP3+ 8 TP3- 65274 RJ-45 Connector OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-15
  • Cisco 7606 | Processor Guide - Page 90
    is used to connect fiber-optic module ports with the external network. (See Figure installing them. For fiber-optic connector cleaning instructions, see the "Cleaning the Fiber-Optic Connectors" section on page B-18. B-16 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7606 | Processor Guide - Page 91
    on the Supervisor Engine 720, Route Switch Processor 720, and RSP720-10GE uplink ports use either MT-RJ connectors or LC connectors depending on the SFP module vendor. Figure B-7 shows an LC connector. OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-17
  • Cisco 7606 | Processor Guide - Page 92
    connectors with canned, dry, oil-free, compressed air. Use a magnifying glass or inspection microscope to inspect the ferrule. If contaminants are visible, repeat the cleaning procedure. B-18 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7606 | Processor Guide - Page 93
    Specifications while cleaning the chassis. • Cover the cord is required. You must install the patch cord (Cisco product number CAB-GELX Configuration Example Figure B-8 shows a typical patch cord configuration. OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7606 | Processor Guide - Page 94
    Plant" into the patch panel. The patch cord is 9.84 feet (3 meters) long and has duplex SC male connectors at each end. Figure B-9 Patch Cord Installation To equipment To cable plant 13089 B-20 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11
  • Cisco 7606 | Processor Guide - Page 95
    static electricity caution 14 OL-10100-11 INDEX Cisco 7600 series router features 3 overview 1 commands copy running-config 7 write 7 CompactFlash and MicroDrive support 13 CompactFlash cards front-panel slot 15, 22, 12 installing 13 removing 14 connecting modem 10 terminal to supervisor engine or
  • Cisco 7606 | Processor Guide - Page 96
    7600 series router components 6 modules 8 supervisor engines and RSPs 8 http //www.cisco.com/en/US/docs/ios/ha/command/refere nce/ha_book.html 12 //www.cisco.com/en/US/docs/ios/qos/command/refer ence/qos_book.html 13 I installing flash memory cards 13 modules 4 patch cord 20 interfaces, addresses of
  • Cisco 7606 | Processor Guide - Page 97
    CompactFlash support 13 connecting to 9, 10 hot swapping (OIR) 8 installing 4 removing 7 tools for installing and removing 3 Route Switch Processor 720 (RSP720) 22 CompactFlash support 12 front panel (figure) 9 OL-10100-11 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
  • Cisco 7606 | Processor Guide - Page 98
    9 tools required for installing cards 3 U uplink ports connecting to 10 description 22 RSP720 11 Sup2 11 Sup32 11 Sup720 11 USB ports, Sup32 22 W write command 7 write-protection switch, flash memory card (figure) 12 WS-X6380-NAM 1 IN-4 Cisco 7600 Series Router Supervisor Engine and Route Switch
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Cisco 7600 Series Router
Supervisor Engine and
Route Switch Processor Guide
March 2012
Text Part Number: OL-10100-11