Cisco 881W Hardware Installation Guide

Cisco 881W - Integrated Services Router Wireless Manual

Get Cisco 881W - Integrated Services Router Wireless PDF manuals and user guides
UPC - 882658171802
View all Cisco 881W manuals
Add to My Manuals
Save this manual to your list of manuals

Cisco 881W manual content summary:

  • Cisco 881W | Hardware Installation Guide - Page 1
    Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number:
  • Cisco 881W | Hardware Installation Guide - Page 2
    are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental. Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide © 2010 Cisco Systems, Inc. All rights reserved.
  • Cisco 881W | Hardware Installation Guide - Page 3
    perform initial configuration for the wireless and nonwireless Cisco 860 series, Cisco 880 series, and Cisco 890 series Integrated Services Routers (ISRs). Some information may not apply to your particular router model. For warranty, service, and support information, see the "Cisco One-Year Limited
  • Cisco 881W | Hardware Installation Guide - Page 4
    loss of data. Tip Means the following information will help you solve a problem. The tip information might not be troubleshooting or even an action, but could be useful information. Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide iv
  • Cisco 881W | Hardware Installation Guide - Page 5
    un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procé référez-vous au numéro de l'instruction situé à la fin de chaque avertissement Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
  • Cisco 881W | Hardware Installation Guide - Page 6
    nd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide vi OL-16193-03
  • Cisco 881W | Hardware Installation Guide - Page 7
    Preface OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide vii
  • Cisco 881W | Hardware Installation Guide - Page 8
    åelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide viii OL-16193-03
  • Cisco 881W | Hardware Installation Guide - Page 9
    Preface OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide ix
  • Cisco 881W | Hardware Installation Guide - Page 10
    1037 Warning Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Statement 1038 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide x OL-16193-03
  • Cisco 881W | Hardware Installation Guide - Page 11
    instructions before connecting the system to the power source. Statement 1004 Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers
  • Cisco 881W | Hardware Installation Guide - Page 12
    Bridges, versions 12.4(10b) JA and 12.3(8) JEC • Wireless LAN Controllers • Unified Wireless LAN Access Points • Cisco IOS Voice Port Configuration Guide • SCCP Controlled Analog (FXS) Ports with Supplementary Features in Cisco IOS Gateways • Cisco CP Express User's Guide Searching Cisco Documents
  • Cisco 881W | Hardware Installation Guide - Page 13
    feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0. OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide xiii
  • Cisco 881W | Hardware Installation Guide - Page 14
    Preface Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide xiv OL-16193-03
  • Cisco 881W | Hardware Installation Guide - Page 15
    optional rack-mount features. These ISRs are powered by an external power supply adapter. The various models differ in the WAN interface and features that they support. OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-1
  • Cisco 881W | Hardware Installation Guide - Page 16
    fixed-configuration data routers that support the following features: • An integrated 4-port 10/100 Ethernet switch for connecting to the LAN • A10/100 Fast Ethernet (FE) or ADSL2 over POTs port for connecting to the WAN • Optional, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP Figure
  • Cisco 881W | Hardware Installation Guide - Page 17
    Reset button 2 Antenna-captive omnidirectional dipole WLAN antenna (wireless models only) 6 Power connector 3 4-port 10/100 Ethernet switch 7 Earth ground connection 4 Serial port-console or auxiliary 8 Kensington security slot 1. Depending on the router model, the primary WAN port can be 10
  • Cisco 881W | Hardware Installation Guide - Page 18
    model, the primary WAN port can be G.SHDSL, VDSL2oPOTS, or 10/100 FE. See the Cisco 880 Series Integrated Services Routers data sheet for the WAN interface that is supported on your router. Figure 1-3 shows the front panel details of the Cisco 880 wireless data router. The USB port and the 3G card
  • Cisco 881W | Hardware Installation Guide - Page 19
    the Cisco 888W Data Router 231951 1 2 3 4 5 67 8 9 10 1 ISDN port-not available on 3G models 2 Primary WAN port1-G.SHDSL, VDSL2oPOTS, ADSL2+oPOTS, ADSL2+oISDN, or 10/100 FE 6 PoE power connector-optional 7 Reset button 3 Antenna-captive omnidirectional dipole WLAN antenna (wireless models
  • Cisco 881W | Hardware Installation Guide - Page 20
    Cisco 888E and Cisco 888E-W Data Router B C RX/TX RX A RX/TX 253233 1 2 3 4 5 67 8 9 10 1 ISDN port-not available on 3G models 6 PoE power connector-optional 2 Primary WAN port1-RJ-45 only, G.SHDSL, 7 Reset button VDSL2oPOTS, ADSL2+oPOTS, ADSL2+oISDN, or 10/100 FE 3 Antenna-captive
  • Cisco 881W | Hardware Installation Guide - Page 21
    Cisco 888EG Data Router Cisco 880 Series ISRs 253231 12 3 4 5 67 8 9 10 1 3G Diag port 6 PoE power connector-optional 2 Primary WAN port1-RJ-45 only, G.SHDSL, 7 Reset button VDSL2oPOTS, ADSL2+oPOTS, ADSL2+oISDN, or 10/100 FE 3 Antenna-captive omnidirectional dipole WLAN antenna (wireless
  • Cisco 881W | Hardware Installation Guide - Page 22
    front panel details of the Cisco 880 series wireless voice router. Figure 1-7 Front Panel of the Cisco 880 Series Wireless Voice Router 1 1 LEDs 2 2 USB port 270495 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-8 OL-16193-03
  • Cisco 881W | Hardware Installation Guide - Page 23
    4-port 10/100 Ethernet switch 6 Antenna-captive wireless omnidirectional dipole WLAN antenna (wireless models only) 7 Reset button 8 Power connector 4 Serial port-console or auxiliary 5 PoE power connector-optional 9 Earth ground connection 10 Kensington security slot 1. Depending on the router
  • Cisco 881W | Hardware Installation Guide - Page 24
    dipole WLAN antenna (wireless models only) IAD888EF 2 Voice ports-four FXS2/DID3 ports and one 7 Reset button voice BRI 4port 3 4-port 10/100 Ethernet switch 8 Power connector 4 Serial port-console or auxiliary 9 Earth ground connection 5 PoE power connector-optional 10 Kensington security
  • Cisco 881W | Hardware Installation Guide - Page 25
    . 9 Reset button 4 Primary WAN port-G.SHDSL, RJ-45 only 10 Power connector on the C888ESRST-W. 5 Antenna-captive wireless omnidirectional 11 Earth ground connection dipole WLAN antenna (wireless models only) 6 4-port 10/100 Ethernet switch 12 Kensington security slot 1. Depending on the router
  • Cisco 881W | Hardware Installation Guide - Page 26
    of the Cisco 890 Series Wireless ISR 272367 1 2 Figure 1-12 Rear Panel of the Cisco 890 Series Wireless ISR 241905 2 1 LEDs 1 2 6 3 4 578 9 10 2 USB ports 1-12 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16193
  • Cisco 881W | Hardware Installation Guide - Page 27
    swivel antenna attached to 7 PoE power connector RP-TNC connectors (wireless models only) 2 Backup-Data BRI1 or V.922 port 8 Reset button 3 Primary WAN port-FE and GE 9 Power connector 4 Auxiliary port 10 Earth ground connection 5 Console port 11 Kensington security slot 6 8-port 10/100
  • Cisco 881W | Hardware Installation Guide - Page 28
    . To restore the router configuration to the default configuration set by the factory, simultaneously press the reset button while applying power to the router. Note When the CLI reboot command is issued while the embedded wireless AP is running Cisco Unified IOS software, the router reboots and the
  • Cisco 881W | Hardware Installation Guide - Page 29
    -Ethernet link is up, but wireless AP is not communicating with LWAPP controller. PoE4 Green Off-Ethernet link is down. On-PoE is connected and powered. Off-PoE is not installed. - Models Models with PoE with PoE VPN5 PPP6 Amber On-Fault with the PoE. Green On-VPN is connected. Green On-At
  • Cisco 881W | Hardware Installation Guide - Page 30
    port is either receiving or transmitting data. 881 - SRSTSRS T16models BRI Voice LNK Green On-BRI interface is connected. - 888 SRST - models 886, 887V, 888, SRST models 1-16 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
  • Cisco 881W | Hardware Installation Guide - Page 31
    flash memory contains the Cisco IOS software image, the boot flash contains the ROMMON boot code, and a separate non-volatile flash contains the cookie configuration. OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-17
  • Cisco 881W | Hardware Installation Guide - Page 32
    connected to FE ports 0, 1, 2, and 3. The PoE module is an option available only for the Cisco 880 series and 890 series ISRs and requires a 48-V external power adapter. 1-18 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16193
  • Cisco 881W | Hardware Installation Guide - Page 33
    Cisco 880 Series Integrated Services Routers data sheet. Wireless LAN Connectivity The embedded Wi-Fi CERTIFIED™, 802.11a/b/g/n-compliant wireless AP is preinstalled in the router as an optional feature. The Cisco 860 series routers support autonomous features and network configurations. The Cisco
  • Cisco 881W | Hardware Installation Guide - Page 34
    Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs Feature Description 860 Series 880 Series 890 Series Reset button FE1 built-in switch ports Resets the router configuration to the factory default. All models Provides connection to 10/100BASE-T (10/100-Mbps) Fast
  • Cisco 881W | Hardware Installation Guide - Page 35
    to the router. The Cisco 880 series routers support a 2-port PoE module; the Cisco 890 series routers support a 4-port PoE module. Provides 2-wire or 4-wire connection to a G.SHDSL - network. Provides backup data link. - Detects when the router is about to lose power, and sends a - power-fail
  • Cisco 881W | Hardware Installation Guide - Page 36
    rate digital subscriber line), and G.SHDSL. 7. GE = Gigabit Ethernet 8. VDSL2oPOTS = very-high-data-rate digital subscriber line 2 over plain old telephone service. 9. PoE = Power over Ethernet. 10. G.SHDSL = (global industry standard) symmetrical high-speed DSL. 11. 3G = Third-Generation. 12. DSLAM
  • Cisco 881W | Hardware Installation Guide - Page 37
    and Safety Information for Cisco 800 Series and SOHO Series Routers. Warning Read the installation instructions before connecting the system to the power source. Statement 1004 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement
  • Cisco 881W | Hardware Installation Guide - Page 38
    Cisco 860 Series Routers 1 1 Cisco 880 Series Routers 1 1 Cisco 890 Series Routers 1 1 RJ-45-to-DB-9 console cable 1 1 1 External 12 VDC power supply adapter 1 1 1 AC power supply cable 1 1 1 Cisco Configuration Professional (Cisco CP) 1 1 1 CD4 1. Cisco 861 and Cisco 881 ISRs
  • Cisco 881W | Hardware Installation Guide - Page 39
    plan to configure the software using Cisco IOS commands through the console port, provide an ASCII terminal or a PC that is running terminal emulation software to connect to the console port. • If you plan to connect a modem, provide the modem and modem cable. • If you plan to use the Data BRI port
  • Cisco 881W | Hardware Installation Guide - Page 40
    Caution Do not install the router or power supplies next to a heat source of any kind, including heating vents. Installing Antennas The Cisco 890 series wireless routers have three reverse-polarity threaded Neill-Concelman (RP-TNC) connectors on the back panel. The antennas that are shipped with the
  • Cisco 881W | Hardware Installation Guide - Page 41
    Chapter 2 Installing the Router Figure 2-2 Antennas Oriented Vertically Up Installing the Router 274774 OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 2-5
  • Cisco 881W | Hardware Installation Guide - Page 42
    2-10. Mounting on a Wall The Cisco 860 series, 880 series, and 890 series ISRs have mounting holes on the bottom of the chassis for mounting the unit on a wall or other vertical surface. Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
  • Cisco 881W | Hardware Installation Guide - Page 43
    3.673 in. 1 1 5.961 in. 231987 1 Wall-mount holes Step 2 Hang the router on the screws, and place the power adapter on a nearby horizontal surface. See Figure 2-5. OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 2-7
  • Cisco 881W | Hardware Installation Guide - Page 44
    cm) Step 3 Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the "Installing the Router Ground Connection" section on page 2-10. Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 2-8 OL
  • Cisco 881W | Hardware Installation Guide - Page 45
    Do not overtorque the screws. The recommended torque is 6 to 8 in-lb (0.7 to 0.9 N-m). Figure 2-7 Attaching the Rack-mount Brackets to the Cisco 890 Series ISR 272484 OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 2-9
  • Cisco 881W | Hardware Installation Guide - Page 46
    provided screws with captive locking washers. For a ring terminal, use one of the screws provided. Tighten the screws to a torque of 8 to 10 in-lb (0.9 to 1.1 N-m). 2-10 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16193-03
  • Cisco 881W | Hardware Installation Guide - Page 47
    and properly ground the router, you can connect the power wiring, the WAN and LAN cables, and the cables for administrative access as required for your installation. OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 2-11
  • Cisco 881W | Hardware Installation Guide - Page 48
    Installing the Router Chapter 2 Installing the Router 2-12 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16193-03
  • Cisco 881W | Hardware Installation Guide - Page 49
    have antennas or antenna connectors on the back panel. However, the procedures for connecting devices to the router are the same for both wireless and nonwireless routers. OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
  • Cisco 881W | Hardware Installation Guide - Page 50
    devices to your router: • Turn off power to the devices and to the router until all connections are completed. Caution Do not turn on the devices until after you have completed all connections to the router. • Connect the color-coded cables supplied by Cisco Systems to the color-coded ports on the
  • Cisco 881W | Hardware Installation Guide - Page 51
    ports. Note Use the Cisco Configuration Express to configure the Internet connection settings. See Cisco Configuration Professional Quick Start Guide for more information. OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
  • Cisco 881W | Hardware Installation Guide - Page 52
    # 1 Yellow Ethernet cable 2 Ethernet switch port 1 on the router 3 RJ-45 port on a phone Step 2 Connect the other end of the cable to the RJ-45 port on the phone. Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-4 OL-16193-03
  • Cisco 881W | Hardware Installation Guide - Page 53
    port. Step 2 Step 3 Connect the other end of the cable to the available port on the Ethernet switch to add additional Ethernet connections. Turn on the Ethernet switch. OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
  • Cisco 881W | Hardware Installation Guide - Page 54
    steps: Step 1 Connect one end of the straight-through R-J11 cable to the V.92 port. Step 2 Connect the other end of the straight through R-J11 cable to an RJ-11 telephone wall outlet. Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
  • Cisco 881W | Hardware Installation Guide - Page 55
    Console Port Connect a terminal or PC to the Console Aux port either to configure the software by using the command-line interface (CLI) or to troubleshoot problems with the router. To connect a terminal or PC to the console port on the router and access the CLI, follow these steps: Step 1 Connect
  • Cisco 881W | Hardware Installation Guide - Page 56
    if required) 4 Modem Step 2 Connect the DB-9 end of the console cable to the DB-9 end of the modem adapter. Step 3 Connect the DB-25 end of the modem adapter to the modem. Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-8 OL-16193
  • Cisco 881W | Hardware Installation Guide - Page 57
    modem and the router auxiliary port are configured for the same transmission speed (up to 115200 bits per second [b/s] is supported) and support mode control with data carrier detect (DCD) and data terminal ready (DTR). Connecting the 3G Card Note The Cisco 880G router does not support OIR of the
  • Cisco 881W | Hardware Installation Guide - Page 58
    bracket, as shown in Figure 3-8. Figure 3-8 Opening the Anti-theft Locking Bracket Front View Back View 271474 1 1 1 Pins on the locking bracket for alignment 3-10 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16193-03
  • Cisco 881W | Hardware Installation Guide - Page 59
    Connecting the Router Connecting the 3G Card Step 3 router. Figure 3-9 Installing the Locking Bracket 271726 1 3 1 3G card 2 Locking bracket 2 3 Notch on the 3G card OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
  • Cisco 881W | Hardware Installation Guide - Page 60
    Step 6 To connect the antenna to the 3G card, insert the antenna connector into the antenna connector hole on the 3G card. Figure 3-12 show the antenna connected to the 3G card. 3-12 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
  • Cisco 881W | Hardware Installation Guide - Page 61
    the Router Figure 3-12 Antenna connected to the 3G Card Connecting a Data BRI Port 272653 1 3 2 1 Antenna on a cradle 2 Antenna connector 3 Antenna connector receptacle1 1. In HSPA cards, the antenna connector receptacle is located on the right side of the 3G card. Step 7 Step 8 Clean
  • Cisco 881W | Hardware Installation Guide - Page 62
    5 89 5 10 1 Data BRI port on the router 2 ISDN S/T cable 3 Network termination 1 (NT1) box 4 S/T port on the NT1 box 5 Unshielded CAT 5 cable 6 U-port on the NT1 box 7 xDSL splitter (provided by the xDSL service provider) 8 Telephone line port on the splitter 9 Telecommunication service port on
  • Cisco 881W | Hardware Installation Guide - Page 63
    1 WAN FE 4 1 2 3 Internet 1 FE WAN port 2 CAT 5 cable 3 Modem connected to the Internet Step 2 Connect the other end of cable to an available port on the modem. OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-15
  • Cisco 881W | Hardware Installation Guide - Page 64
    GE WAN Port 274493 1 2 3 Internet 1 GE WAN port 2 CAT 5 cable 3 Modem connected to the Internet Step 2 Connect the other end of cable to an available port on the modem. 3-16 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL
  • Cisco 881W | Hardware Installation Guide - Page 65
    -45 connector is inserted Note The DSL line must be provisioned by your service provider and correctly configured so that the LED shows the carrier detect (CD) status. OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-17
  • Cisco 881W | Hardware Installation Guide - Page 66
    one power supply connection. All connections must be removed to de-energize the unit. Statement 1028 Figure 3-17 shows how to connect the 48-VDC Power over Ethernet (PoE) power adapter to your router. The PoE adapter provides power to ports 0 and 1 of the 4-port 10/100 FE switch on the Cisco 880
  • Cisco 881W | Hardware Installation Guide - Page 67
    unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028 To connect your Cisco 860 series or Cisco 880 series ISR to an AC power outlet, follow these steps: Step 1 Connect the router to an AC power outlet as shown in Figure 3-18
  • Cisco 881W | Hardware Installation Guide - Page 68
    Figure 3-19. Figure 3-19 Securing the Power Cord 3 2 4 1 270659 1 Power lock clip 2 Power cord 3 DC plug 4 Lock holes on either side of the power connector 3-20 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16193-03
  • Cisco 881W | Hardware Installation Guide - Page 69
    building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection: FXS. OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-21
  • Cisco 881W | Hardware Installation Guide - Page 70
    Fax machine or telephone 1 FXS port 2 RJ-11 cable 3 RJ-11 port Step 2 Connect the other end of the cable to the RJ-11 port on the fax or telephone machine. 241907 3-22 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16193-03
  • Cisco 881W | Hardware Installation Guide - Page 71
    22 Connecting an FXO Line 270542 2 1 3 1 FXO port 2 RJ-11 cable 3 Telephone outlet Step 2 Connect the other end of the RJ-11 cable to a telephone wall outlet. OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-23
  • Cisco 881W | Hardware Installation Guide - Page 72
    RJ-45-to-RJ-45 cable to the Voice BRI port. Note When the interface is configured as NT and is connecting to a TE device, use a crossover cable. See Table A-11. 3-24 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16193-03
  • Cisco 881W | Hardware Installation Guide - Page 73
    BRI Line 2 3 1 Voice BRI port 2 RJ-45 cable 3 Telephone outlet Step 2 Connect the other end of the cable to the RJ-45 telephone outlet or other device. 241906 OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-25
  • Cisco 881W | Hardware Installation Guide - Page 74
    FE4 To xDSL2 line To ISDN line 3G4 xDSL CD xDSL Data Data BRI LNK Data BRI B1 and B2 WWAN5 RSSI6 To PPP9 clients To VPN12 tunnel CDMA7 GSM8 PPP VPN Normal Patterns On when power is supplied to the router. On when the FE LAN port is physically connected to a server, PC, workstation, or external
  • Cisco 881W | Hardware Installation Guide - Page 75
    Protocol. 10. PPPoE = PPP over Ethernet. 11. PPPoA = PPP over ATM. 12. VPN = Virtual Private Network. 13. SSID = service set identifier. 14. PoE = Power over Ethernet. OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-27
  • Cisco 881W | Hardware Installation Guide - Page 76
    Verifying Connections Chapter 3 Connecting the Router 3-28 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16193-03
  • Cisco 881W | Hardware Installation Guide - Page 77
    the router see the Cisco CP Express User's Guide. Cisco IOS CLI To configure the initial router settings by using the Cisco IOS CLI, you will need to set up a console connection. For instructions on how to set up a console connection, see the "Connecting a Terminal or PC to the Console Port" section
  • Cisco 881W | Hardware Installation Guide - Page 78
    the Cisco IOS CLI for initial configuration, see the applicable configuration procedures in the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Software Configuration Guide. Note Save your configuration changes regularly to avoid losing them during resets, power
  • Cisco 881W | Hardware Installation Guide - Page 79
    to enter basic management setup: At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware
  • Cisco 881W | Hardware Installation Guide - Page 80
    the system Would you like to enter basic management setup? [yes/no]: yes Step 5 Enter a hostname for the router (this example uses Router): Configuring global parameters: Enter host name [Router]: Router Step 6 Enter an enable secret password. This password is encrypted (more secure) and cannot
  • Cisco 881W | Hardware Installation Guide - Page 81
    IOS. You can initially configure the embedded wireless AP by using one of the following methods: • Cisco Configuration Professional (CP) Express • Setup command facility on the embedded wireless device OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers
  • Cisco 881W | Hardware Installation Guide - Page 82
    to do basic wireless configuration on your router see the "Basic Wireless Device" chapter of the Cisco 860 Series, Cisco 880, and Cisco 890 Series Integrated Services Routers Software Configuration Guide. Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware
  • Cisco 881W | Hardware Installation Guide - Page 83
    Cisco 880 series, and Cisco 890 series Integrated Services Routers (ISRs). It contains the following sections: • Router Specifications, page A-2 • Wireless Access Point, page A-3 • FE and GE Port Pinouts, page A-3 • Console and Auxiliary Port Connector Pinouts, page A-4 • FXS and FXO Port Connector
  • Cisco 881W | Hardware Installation Guide - Page 84
    voltages +12 VDC Inline Power-over-Ethernet Adapter Input voltage 85 to 264 VAC Input frequency 47 to 63 Hz Power output 80 W, maximum Output voltage -48 VDC Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide A-2 OL-16193-03
  • Cisco 881W | Hardware Installation Guide - Page 85
    Table A-3 lists the pinouts for the Ethernet ports. Table A-3 Pin 1 2 3 4 5 6 7 8 Ethernet LAN Port Pinouts Function RX+ RX- TX+ Unused Unused TX- Unused Unused OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide A-3
  • Cisco 881W | Hardware Installation Guide - Page 86
    Port Connector Pinouts Table A-6 lists the VDSL2 connector pinouts. Table A-6 VDSL2 Connector Pinouts (RJ-11-to-RJ-45) RJ-11 Pin 1 2 3 4 Function Unused Unused TIP RING Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide A-4 OL
  • Cisco 881W | Hardware Installation Guide - Page 87
    92 Port Connector Pinouts Table A-8 lists the V.92 connector pinouts. Table A-8 V.92 Connector Pinouts (RJ-11-to-RJ-45) RJ-11 Pin 1 2 3 4 5 6 Function Unused Unused TIP RING Unused Unused OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware
  • Cisco 881W | Hardware Installation Guide - Page 88
    (Port0) 5 TIP (Port1) 6 Unused Data BRI Port Connector Pinouts Table A-10 lists the pinouts for the Data BRI port. Table A-10 Data BRI Port Pinouts Pin Function 1 Unused 2 Unused 3 TXP 4 RXP 5 TXN 6 TXN 7 Unused 8 Unused Voice ISDN BRI Interface Pin Numbers and Functions
  • Cisco 881W | Hardware Installation Guide - Page 89
    cables that connect equipment to the router is 328 feet (100 meters). This length is also the maximum distance between the router and the equipment connected to it. OL-16193-03 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide A-7
  • Cisco 881W | Hardware Installation Guide - Page 90
    Cable Specifications Appendix A Technical Specifications Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide A-8 OL-16193-03
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Cisco 860 Series, Cisco 880 Series, and
Cisco 890 Series Integrated Services
Routers Hardware Installation Guide
Text Part Number: