Home » Cisco Manuals » Wireless » Cisco AIR-AP1242AG-E-K9 » Manual Viewer

Cisco AIR-AP1242AG-E-K9 Hardware Installation Guide - Page 118

Declaration of Conformity for RF Exposure

View all Cisco AIR-AP1242AG-E-K9 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

Declaration of Conformity for RF Exposure Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity for RF Exposure The radio module has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices as defined in Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. For the IEEE 802.11B antennas, AIR-ANT24120, AIR-ANT4121 and AIR-ANT1949 the equipment should be positioned more than 2 m (6.56 ft) from your body or nearby persons. For all other approved antennas the equipment shoud be installed more than 20 cm (7.9 in.) from your body or nearby persons. The access point (with 5 GHz integrated antenna) must be installed to maintain a minimum 20 cm (7.9 in.) co-located separation distance from other FCC approved indoor/outdoor antennas used with the access point. Any antennas or transmitters not approved by the FCC cannot be co-located with the access point antennas. The access point's co-located 2.4 GHz (2.2 dBi) and 5 GHz integrated antennas support a minimum separation distance of 10 cm (3.9 in.) and are compliant with the applicable FCC RF exposure limit when transmitting simultaneously. Note Dual antennas used for diversity operation are not considered co-located. Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English. Japanese Translation 03-5549-6500 Cisco Aironet 1200 Series Access Point Hardware Installation Guide B-6 OL-4310-05 43768

Section	Page
Cisco Aironet 1200 Series Access Point Hardware Installation Guide	1
Contents	3
Preface	9
Audience	9
Purpose	9
Organization	9
Conventions	10
Related Publications	12
Obtaining Documentation	12
Cisco.com	13
Product Documentation DVD	13
Ordering Documentation	13
Documentation Feedback	14
Cisco Product Security Overview	14
Reporting Security Problems in Cisco Products	14
Obtaining Technical Assistance	15
Cisco Technical Support & Documentation Website	15
Locating the Product Serial Number	16
Submitting a Service Request	16
Definitions of Service Request Severity	17
Obtaining Additional Publications and Information	17
Overview	19
Hardware Features	20
Dual-Radio Operation	20
LEDs	21
Ethernet Port	21
Console Port	22
Power Sources	22
UL 2043 Certification	22
Anti-Theft Features	23
Network Configuration Examples	23
Central Unit in an All-Wireless Network	23
Root Access Point on a Wired LAN	24
Repeater Unit that Extends Wireless Range	25
Point-to-Point Bridge Configuration	25
Workgroup Bridge Configuration	26
Installing the Access Point	27
Safety Information	28
FCC Safety Compliance Statement	28
General Safety Guidelines	28
Warnings	28
Unpacking the Access Point	29
Package Contents	29
Basic Installation Guidelines	29
Installation Above Suspended Ceilings	30
Before Beginning the Installation	30
Installation Summary	32
Connecting the 2.4-GHz Antennas	32
Connecting the 5-GHz External Antennas	33
Connecting the Ethernet and Power Cables	34
Connecting to an Ethernet Network with an Inline Power Source	35
Connecting to an Ethernet Network with Local Power	35
Powering Up the Access Point	36
Configuring the Access Point for the First Time	37
Before You Start	38
Resetting the Access Point to Default Settings	38
Using the Mode Button	38
Using a Web-browser	38
Default IP Address Behavior	39
Obtaining and Assigning an IP Address	39
Connecting to the Access Point Locally	40
Assigning Basic Settings	40
Default Settings on the Express Setup Page	44
Enabling the Radio Interfaces	45
Configuring Basic Security Settings	45
Understanding Express Security Settings	47
Using VLANs	47
Express Security Types	47
Express Security Limitations	48
Using the Express Security Page	49
Assigning an IP Address Using the CLI	50
Using a Telnet Session to Access the CLI	50
Using the Web-Browser Interface	51
Using the Web-Browser Interface for the First Time	52
Using the Management Pages in the Web-Browser Interface	52
Using Action Buttons	54
Character Restrictions in Entry Fields	55
Using Online Help	55
Using the Command-Line Interface	57
Cisco IOS Command Modes	58
Getting Help	59
Abbreviating Commands	59
Using no and default Forms of Commands	59
Understanding CLI Messages	60
Using Command History	60
Changing the Command History Buffer Size	60
Recalling Commands	61
Disabling the Command History Feature	61
Using Editing Features	61
Enabling and Disabling Editing Features	62
Editing Commands Through Keystrokes	62
Editing Command Lines that Wrap	63
Searching and Filtering Output of show and more Commands	64
Accessing the CLI	64
Opening the CLI with Telnet	64
Opening the CLI with Secure Shell	65
Mounting Instructions	67
Overview	68
Mounting on a Horizontal or Vertical Surface	69
Mounting Below a Suspended Ceiling	70
Mounting Above a Suspended Ceiling	71
Attaching the Access Point to the Mounting Bracket	73
Securing the Access Point to the Mounting Bracket	73
2.4-GHz Radio Upgrade	75
Upgrade Overview	76
Unpacking the Radio	76
Opening the Access Cover	77
Removing a Blank Spacer Card	78
Removing a 2.4-GHz Radio	79
Installing a 2.4-GHz Radio	81
Attaching the Compliance Labels	83
Placing the Labels	84
Finding the Software Version	84
5-GHz Radio Module Upgrade	85
Upgrade Overview	86
Unpacking the Radio Module	86
Removing the 5-GHz Radio Access Cover	86
Removing a 5-GHz Radio Module	87
Installing a 5-GHz Radio Module	89
Attaching the Compliance Label	91
Finding the Software Version	92
Troubleshooting	93
Checking the Top Panel LEDs	94
Checking Basic Settings	96
Default IP Address Behavior	96
Default SSID and Radio Behavior	96
Enabling the Radio Interfaces	96
SSID	97
WEP Keys	97
Security Settings	97
Running the Carrier Busy Test	97
Running the Ping or Link Test	98
Resetting to the Default Configuration	99
Using the MODE Button	99
Using the Web Browser Interface	100
Reloading the Access Point Image	100
Using the MODE button	101
Web Browser Interface	101
Browser HTTP Interface	102
Browser TFTP Interface	102
Obtaining the Access Point Image File	103
Obtaining the TFTP Server Software	104
Translated Safety Warnings	105
Statement 245B—Explosive Device Proximity Warning	106
Statement 332—Antenna Installation Warning	107
Statement 1001—Work During Lightning Activity Warning	108
Statement 1004—Installation Instructions Warning	109
Statement 1005—Circuit Breaker (20A) Warning	110
Declarations of Conformity and Regulatory Information	113
Manufacturers Federal Communication Commission Declaration of Conformity Statement	114
Department of Communications—Canada	115
Canadian Compliance Statement	115
European Community, Switzerland, Norway, Iceland, and Liechtenstein	116
Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC	116
Declaration of Conformity for RF Exposure	118
Guidelines for Operating Cisco Aironet Access Points in Japan	118
Japanese Translation	118
English Translation	119
Administrative Rules for Cisco Aironet Access Points in Taiwan	119
Access Points with IEEE 802.11a Radios	119
Chinese Translation	119
English Translation	119
All Access Points	120
Chinese Translation	120
English Translation	120
Operation of Cisco Aironet Access Points in Brazil	121
Access Point Model	121
Regulatory Information	121
Portuguese Translation	121
English Translation	121
Declaration of Conformity Statements	122
Declaration of Conformity Statements for European Union Countries	122
Access Point Specifications	131
Channels and Antenna Settings	137
Channels	138
IEEE 802.11b (2.4-GHz Band)	138
IEEE 802.11g (2.4-GHz Band)	139
IEEE 802.11a (5-GHz Band)	140
Maximum Power Levels and Antenna Gains	142
IEEE 802.11b (2.4-GHz Band)	142
IEEE 802.11g (2.4-GHz Band)	143
IEEE 802.11a (5-GHz Band)	144
Console Cable Pinouts	149
Overview	150
Console Port Signals and Pinouts	150
Glossary	151

Match case Limit results 1 per page

B-6

Cisco Aironet 1200 Series Access Point Hardware Installation Guide

OL-4310-05

Appendix B

Declarations of Conformity and Regulatory Information

Declaration of Conformity for RF Exposure

The radio module has been found to be compliant to the requirements set forth in CFR 47 Sections

2.1091, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices as defined in

Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic

Fields. For the IEEE 802.11B antennas, AIR-ANT24120, AIR-ANT4121 and AIR-ANT1949 the

equipment should be positioned more than 2 m (6.56 ft) from your body or nearby persons. For all other

approved antennas the equipment shoud be installed more than 20 cm (7.9 in.) from your body or nearby

persons.

The access point (with 5 GHz integrated antenna) must be installed to maintain a minimum 20 cm

(7.9 in.) co-located separation distance from other FCC approved indoor/outdoor antennas used with the

access point. Any antennas or transmitters not approved by the FCC cannot be co-located with the access

point antennas. The access point’s co-located 2.4 GHz (2.2 dBi) and 5 GHz integrated antennas support

a minimum separation distance of 10 cm (3.9 in.) and are compliant with the applicable FCC RF

exposure limit when transmitting simultaneously.

Note

Dual antennas used for diversity operation are not considered co-located.

Guidelines for Operating Cisco Aironet Access Points in Japan

This section provides guidelines for avoiding interference when operating Cisco Aironet access points

in Japan. These guidelines are provided in both Japanese and English.

Japanese Translation

03-5549-6500

43768