Cisco ASR1006 Hardware Installation Guide - Page 174

Troubleshooting the 1-Port 10-Gigabit Ethernet LAN/WAN-PHY SPA for ASR 1000 Series Hardware

Page 174 highlights

Troubleshooting the Hardware Chapter 7 Troubleshooting the Installation Troubleshooting the 1-Port 10-Gigabit Ethernet LAN/WAN-PHY SPA for ASR 1000 Series Hardware Table 7-6 This section describes some of the hardware problems that may occur with the 1-Port 10-Gigabit Ethernet LAN/WAN-PHY SPA for also called the SPA-1X-10GE-WL-V2 SPA. Table 7-6 describes the possible problems and solutions for hardware-based out-of-service states. Possible Reasons and Solutions for Hardware-Based Errors on the 1-Port 10-Gigabit Ethernet LAN/WAN-PHY SPA Possible Problem SPA Hardware initialization timeout Observations and Comments Solutions The SPA initialization is performed by SIP. If the 1. Reload or reseat (reinsert) the SPA. initialization of hardware has timed out, a 2. Enter the upgrade hw-module HW-INIT-TIMEOUT message is displayed on the console. subslot fpd bundled command to The show hw-module subslot all oir command displays a start the recovery of the FPD upgrade. "failed too many times" reason code for the out-of-service operational status and the show logging command shows a HW-INIT-TIMEOUT failure. If the problem was due to an FPD image corruption, the SPA should boot normally after the upgrade is The following is an example of a HW-INIT-TIMEOUT complete. message: 3. If the FPD upgrade completes *Mar 3 23:27:05.903: %SPA_OIR-6-ONLINECARD: SPA successfully, but you still have an (SPA-1X10GE-WL-V2) online in subslot 1/1 *Mar 3 23:27:16.488: %SPA_OIR-3-HW_INIT_TIMEOUT: subslot 1/0 error, the SPA probably has a hardware problem. *Mar 3 23:27:21.488: %SPA_OIR-3-RECOVERY_RELOAD: subslot 1/0: Attempting recovery by reloading SPA *Mar 3 23:27:21.489: %SPA_OIR-6-OFFLINECARD: SPA (SPA-1X10GE-WL-V2) offline in subslot 1/0 7-14 Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188

7-14
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide
OL-14126-12
Chapter 7
Troubleshooting the Installation
Troubleshooting the Hardware
Troubleshooting the 1-Port 10-Gigabit Ethernet LAN/WAN-PHY SPA for ASR
1000 Series Hardware
This section describes some of the hardware problems that may occur with the 1-Port 10-Gigabit
Ethernet LAN/WAN-PHY SPA for also called the SPA-1X-10GE-WL-V2 SPA.
Table 7-6
describes the possible problems and solutions for hardware-based out-of-service states.
Table 7-6
Possible Reasons and Solutions for Hardware-Based Errors on the 1-Port 10-Gigabit Ethernet
LAN/WAN-PHY SPA
Possible Problem
Observations and Comments
Solutions
SPA Hardware
initialization
timeout
The SPA initialization is performed by SIP. If the
initialization of hardware has timed out, a
HW-INIT-TIMEOUT message is displayed on the console.
The
show hw-module subslot all oir
command displays a
“failed too many times” reason code for the out-of-service
operational status and the
show logging
command shows a
HW-INIT-TIMEOUT failure.
The following is an example of a HW-INIT-TIMEOUT
message:
*Mar 3 23:27:05.903: %SPA_OIR-6-ONLINECARD: SPA
(SPA-1X10GE-WL-V2) online in subslot 1/1
*Mar 3 23:27:16.488:
%SPA_OIR-3-HW_INIT_TIMEOUT:
subslot 1/0
*Mar 3 23:27:21.488: %SPA_OIR-3-RECOVERY_RELOAD:
subslot 1/0: Attempting recovery by reloading SPA
*Mar 3 23:27:21.489: %SPA_OIR-6-OFFLINECARD: SPA
(SPA-1X10GE-WL-V2) offline in subslot 1/0
1.
Reload or reseat (reinsert) the SPA.
2.
Enter the
upgrade hw-module
subslot fpd bundled
command to
start the recovery of the FPD upgrade.
If the problem was due to an FPD
image corruption, the SPA should
boot normally after the upgrade is
complete.
3.
If the FPD upgrade completes
successfully, but you still have an
error, the SPA probably has a
hardware problem.