Cisco ATA186-I1 Installation Guide

Cisco ATA186-I1 Manual

Get Cisco ATA186-I1 PDF manuals and user guides View all Cisco ATA186-I1 manuals
Add to My Manuals
Save this manual to your list of manuals

Cisco ATA186-I1 manual content summary:

  • Cisco ATA186-I1 | Installation Guide - Page 1
    Cisco ATA 186 and Cisco 188 Installation and Configuration Guide August, 2002 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Customer Order Number: Text Part Number: OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 2
    will be required to correct the interference at their own expense. The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco's installation instructions
  • Cisco ATA186-I1 | Installation Guide - Page 3
    in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0106R) Cisco ATA 186 and Cisco 188 Installation and Configuration Guide Copyright © 2001, Cisco Systems, Inc. All
  • Cisco ATA186-I1 | Installation Guide - Page 4
  • Cisco ATA186-I1 | Installation Guide - Page 5
    1-1 About the Cisco ATA 186 1-1 Hardware Features 1-2 Additional Feature 1-3 Software Features 1-4 General Features 1-4 H.323-specific Features 1-5 SIP Specific Features 1-6 About Supported Standards and Protocols 1-7 Electrical Specifications 1-8 Cisco ATA 186 Installation and Configuration Guide v
  • Cisco ATA186-I1 | Installation Guide - Page 6
    the Web Configuration Page 3-4 About Autoprovisioning 3-5 cfgfmt.exe and ptag.dat Files 3-6 Updating the Profile from the TFTP Server 3-7 About Profile and Configuration Security 3-7 Passwords 3-7 Encrypt Key 3-8 About Using the DHCP Server 3-8 Cisco ATA 186 Installation and Configuration Guide vi
  • Cisco ATA186-I1 | Installation Guide - Page 7
    Call in Sweden 5-2 About Call Waiting 5-3 Call Waiting in the U.S. 5-3 Call Waiting in Sweden 5-3 About Call Forwarding 5-4 Forwarding Calls in the U.S. 5-4 Forwarding Calls in Sweden 5-5 Cisco ATA 186 Installation and Configuration Guide vii
  • Cisco ATA186-I1 | Installation Guide - Page 8
    186 for FAX Mode 7-4 Configuring the Cisco ATA 186 for Fax Mode on a Per-Call Basis 7-5 Configuring the Cisco Gateway for FAX Mode 7-5 Testing and Troubleshooting the Cisco ATA 186 8-1 Testing the Cisco ATA 186 Configuration 8-1 Making a Call 8-1 Cisco ATA 186 Installation and Configuration Guide
  • Cisco ATA186-I1 | Installation Guide - Page 9
    D-1 About Dial Plan Commands D-2 Example 1 D-3 Example 2 (Default Dial Plan) D-4 Dial Plan Blocking D-5 Paid Services and Call Features Parameters and Defaults E-1 Call Progress Tone Parameters and Defaults F-1 Call Progress Tone Parameters F-1 Cisco ATA 186 Installation and Configuration Guide ix
  • Cisco ATA186-I1 | Installation Guide - Page 10
    Context Command Lists G-1 Syntax G-2 Context-Identifiers G-3 Action Identifiers G-4 Call Command Example G-5 Call Command Behaviors G-7 U.S. Call Command G-13 Configuring G-14 Sweden Call Command G-14 Configuring G-16 Terms and Acronyms H-1 Cisco ATA 186 Installation and Configuration Guide x OL
  • Cisco ATA186-I1 | Installation Guide - Page 11
    186 to provide voice over IP (VoIP) services to end users. Note For additional information about the SIP protocol with Cisco ATA, also refer to the Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide (SIP). OL-1267-01 Cisco ATA 186 Installation and Configuration Guide
  • Cisco ATA186-I1 | Installation Guide - Page 12
    one. Examples of information displayed on the screen. Examples of information you must enter. Nonprinting characters, for example passwords, appear in angle brackets. Default responses to system prompts appear in square brackets. Cisco ATA 186 Installation and Configuration Guide xii OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 13
    of data. Tips This symbol means the following information will help you solve a problem. The tips information might not be troubleshooting or even an action, but could be useful information, document that accompanied this device. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide xiii
  • Cisco ATA186-I1 | Installation Guide - Page 14
    traductions d'avertissements figurant dans cette publication, consultez le document Regulatory Compliance and Safety Information (Conformité aux règlements et consignes de sécurité) qui accompagne cet appareil. Cisco ATA 186 Installation and Configuration Guide xiv OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 15
    i denne publikasjonen, kan du se i dokumentet Regulatory Compliance and Safety Information (Overholdelse av forskrifter og sikkerhetsinformasjon) som ble levert med denne enheten. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide xv
  • Cisco ATA186-I1 | Installation Guide - Page 16
    and Safety Information (Efterrättelse av föreskrifter och säkerhetsinformation), vilket medföljer denna anordning. Obtaining Documentation The following sections provide sources for obtaining documentation from Cisco Systems. Cisco ATA 186 Installation and Configuration Guide xvi OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 17
    the form, click Submit to send it to Cisco. You can e-mail your comments to [email protected]. To submit your comments by mail, use the response card behind the front cover of your document, or write to the following address: OL-1267-01 Cisco ATA 186 Installation and Configuration Guide xvii
  • Cisco ATA186-I1 | Installation Guide - Page 18
    configurations from online tools. For Cisco.com registered users, additional troubleshooting tools are available from the Technical Assistance Center (TAC) website. Cisco.com Cisco.com is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco
  • Cisco ATA186-I1 | Installation Guide - Page 19
    .com/register/ If you cannot resolve your technical issue by using the TAC online resources, Cisco.com registered users can open a case online by using the TAC Case Open tool at the following website: http://www.cisco.com/tac/caseopen OL-1267-01 Cisco ATA 186 Installation and Configuration Guide
  • Cisco ATA186-I1 | Installation Guide - Page 20
    cisco.com/warp/public/687/Directory/DirTAC.shtml P1 and P2 level problems are defined as follows: • P1-Your production network is down, causing a critical impact to business operations if service secondo le leggi e regolazioni locali. Cisco ATA 186 Installation and Configuration Guide xx OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 21
    completo de este producto debe seguir todas las leyes y reglamentos nacionales. Varning! Vid deponering hanteras produkten enligt gällande lagar och bestämmelser. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide xxi
  • Cisco ATA186-I1 | Installation Guide - Page 22
    -complexity/CELP codecs, such as G.723.1 and G.729A. • Can be configured to use either the H.323 or the SIP call signaling protocol. • Operates with Cisco Voice Packet Gateways. • Operates with H.323- or SIP-compliant Voice Packet Gateways. OL-1267-01 Cisco ATA 186 Installation and Configuration
  • Cisco ATA186-I1 | Installation Guide - Page 23
    ATA 186 Function button ANALOCGISTCELOEPAHTONAE1A8D6APTOR Indicator LED PHONE 1 PHONE 2 10BaseT ACT 5V 62423 AB C D A-Phone 1 connector (RJ-11) B-Phone 2 connector (RJ-11) C-10Base-T Ethernet connector D-12V power connector OL-1267-01 Cisco ATA 186 Installation and Configuration Guide
  • Cisco ATA186-I1 | Installation Guide - Page 24
    button to access the interactive voice response (IVR) configuration menu. To configure the Cisco ATA 186 by using the IVR mode, see Chapter 3, "Configuring the Cisco ATA 186." - Activity LED The green Activity LED located on the back panel flashes to indicate network activity. • 5 Volt power adapter
  • Cisco ATA186-I1 | Installation Guide - Page 25
    Cisco ATA 186 Call forwarding on no answer from the Cisco ATA 186 Call forwarding on busy from the Cisco ATA 186 Call waiting Calling Line ID Presentation (CLIP) Calling Line ID Rejection (CLIR) Comfort noise generation (CNG) Configurable ring specification Dial Plan Support Feature access
  • Cisco ATA186-I1 | Installation Guide - Page 26
    Cisco registration- and admission-level security support Dual Tone Multiple Frequency (DTMF) relay Empty cap set Fast start/tunneling/early H.245 Details Uses MD5 hashing Uses access/clear token H.245 Including H.245 messages in the Alert message Cisco ATA 186 Installation and Configuration Guide
  • Cisco ATA186-I1 | Installation Guide - Page 27
    the Cisco ATA 186 Details Digest Authentication RFC 2833 Unconditionally, on no answer, or on busy With or without consultation Plays an intermittent dial tone if there is a message waiting. Otherwise, plays a normal dial tone. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 1-6
  • Cisco ATA186-I1 | Installation Guide - Page 28
    Standards and Protocols Chapter 1 Cisco ATA 186 Overview About Supported Standards and Protocols The following standards are supported on the Cisco ATA 186: • Network interface: one RJ-45 8-wire connector, IEEE 802.3 10Base-T standard • Two RJ-11 FXS standard analog telephone voice ports, up
  • Cisco ATA186-I1 | Installation Guide - Page 29
    Chapter 1 Cisco ATA 186 Overview About Supported Standards and Protocols Electrical Specifications Table 1-4 Electrical Specifications Category Voltage Power Power adaptor Specification % non-condensing, operating and storage OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 1-8
  • Cisco ATA186-I1 | Installation Guide - Page 30
    About Supported Standards and Protocols Chapter 1 Cisco ATA 186 Overview Standards Second Edition with Amendments 1, 2, 3, and 4) EN60950:1992 (with Amendments 1, 2, 3, 4, and 11) AS/NZS 3260:1993 (with Amendments 1, 2, 3, and 4) TS001:1997 Cisco ATA 186 Installation and Configuration Guide
  • Cisco ATA186-I1 | Installation Guide - Page 31
    1 Cisco ATA 186 Overview About Supported Standards RF EN61000-4-11, Dips and Sags Dimensions Table 1-7 Dimensions Category Length Width Height Weight Specification 6.5 in (16.5 cm) 6 in (15.25 cm) 1.5 in (3.8 cm) 15 oz (425 gm) OL-1267-01 Cisco ATA 186 Installation and Configuration Guide
  • Cisco ATA186-I1 | Installation Guide - Page 32
    About Supported Standards and Protocols Chapter 1 Cisco ATA 186 Overview 1-11 Cisco ATA 186 Installation and Configuration Guide OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 33
    if you are using SIP. 4. If you will be routing calls through the Public Switched Telephone Network (PSTN), install and configure the Gateway. 5. Install the Cisco ATA 186. 6. Configure the Cisco ATA 186. 7. Perform any troubleshooting and maintenance, including upgrading the software if necessary
  • Cisco ATA186-I1 | Installation Guide - Page 34
    an example of a network with a Cisco ATA 186. Figure 2-1 Example Network Diagram Gatekeeper or Proxy Server PHONE 1 PHONE 2 10BaseT ACT 5V ATA 186 Broadband modem ISP Connection POP IP Network Voice Gateway PSTN 62467 Cisco ATA 186 Installation and Configuration Guide 2-2 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 35
    SIP-complaint software. The gatekeeper must be running the applicable version of software for the features and protocol you want to use. • Voice Packet Gateway-Required if you are connecting to the Public Switched Telephone Network (PSTN). • Fax Cisco ATA 186 Installation and Configuration Guide 2-3
  • Cisco ATA186-I1 | Installation Guide - Page 36
    ATA 186 documentation • 5V Power Adaptor You also need: • 10BaseT category-3 cable or better • One or two analog touch-tone telephones Note Telephones must be set to use tone, rather than pulse dialing for the Cisco ATA 186 to operate correctly. Cisco ATA 186 Installation and Configuration Guide
  • Cisco ATA186-I1 | Installation Guide - Page 37
    Cisco ATA 186 Installation Warnings This section contains important safety information. Number 26 AWG Warning Installation Warnings Warning To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line di sezione 0,12 mm2 (26 Cisco ATA 186 Installation and Configuration Guide 2-5
  • Cisco ATA186-I1 | Installation Guide - Page 38
    Installation Warnings Short-Circuit Protection Warning Chapter 2 Installing the Cisco ATA 186 Warning This product relies on the building's installation for doit être conforme aux normes de sécurité en vigueur dans votre pays. Cisco ATA 186 Installation and Configuration Guide 2-6 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 39
    Chapter 2 Installing the Cisco ATA 186 Installation Warnings Warnung Diese Produkt erfordert eine Gebäudeabsicherung gegen Kurzschluß (Überstrom). Achten Sie necessárias aprovações de segurança por parte das autoridades locais. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 2-7
  • Cisco ATA186-I1 | Installation Guide - Page 40
    som erkänns av användningslandet. TN Power Systems Warning Warning The device is designed to work with TN power systems. Waarschuwing Het apparaat is ontworpen om è stato progettato per l'uso con sistemi di alimentazione TN. Cisco ATA 186 Installation and Configuration Guide 2-8 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 41
    med elkraftssystem av TN-typ. Installing the Cisco ATA 186 Follow these steps to install the Cisco ATA 186 hardware. (See Figure 2-2.) Figure 2-2 Installing the Cisco ATA 186 PHONE 1 PHONE 2 10BaseT ACT 5V 62290 AB OL-1267-01 C D Cisco ATA 186 Installation and Configuration Guide 2-9
  • Cisco ATA186-I1 | Installation Guide - Page 42
    -T Ethernet connector D-12V power connector Step 1 Place the Cisco ATA 186 near an electrical outlet. Connect the first telephone to the PHONE 1 input port (A) on the rear panel of the Cisco ATA 186 by using a telephone line cord with an RJ-11 connector. The PHONE 1 input port will be the primary
  • Cisco ATA186-I1 | Installation Guide - Page 43
    does not flash after power-up, check that the power adaptor is plugged into a working electrical outlet and that the power cord is pushed securely into the connector. Additionally, verify that the Ethernet connection is secure. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 2-11
  • Cisco ATA186-I1 | Installation Guide - Page 44
    Installation Warnings Chapter 2 Installing the Cisco ATA 186 2-12 Cisco ATA 186 Installation and Configuration Guide OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 45
    three ways to configure your Cisco ATA 186: • Voice Configuration Menu • Web browser • Autoprovisioning Configuration Requirements The Cisco ATA 186 requires the following minimum settings for network connectivity: • IP address • Network route address (IP gateway) • Subnet mask Note To enter an IP
  • Cisco ATA186-I1 | Installation Guide - Page 46
    device. Note If there is no DHCP server and the Cisco ATA 186 is programed to find one, the function button will keep blinking. About Using the Voice Configuration Menu Some IVR menu options will require you to enter alphanumerica characters. Alphanumeric entry differs from numeric entry in that
  • Cisco ATA186-I1 | Installation Guide - Page 47
    delimeter) The voice will repeat the value you entered; then, prompt you to press one of the following keys: • 1=change your entered value • 2=review your entered value • 3=save your entered value • 4=review the current saved value OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 3-3
  • Cisco ATA186-I1 | Installation Guide - Page 48
    on top of the Cisco ATA 186. Enter the IVR menu number for the parameter that you want to configure or the command that you want to execute; then, press the pound key (#). (See Appendix A, "Voice Menu Options," and Appendix B, "Parameters and Defaults," for lists of options and their corresponding
  • Cisco ATA186-I1 | Installation Guide - Page 49
    on how to find the IP address of your Cisco ATA 186. Select the values for the items that you want to configure. (See Appendix B, "Parameters and Defaults," for a list of options.) Scroll down to see all parameters. You can password-protect the user interface for security. Click apply to save your
  • Cisco ATA186-I1 | Installation Guide - Page 50
    1, the Cisco ATA 186 will contact the TFTP server continuously without waiting until the next CfgInterval. The value for CfgInterval is the value of CfgInterval in seconds. At CfgInterval, the Cisco ATA 186 attempts to refresh its profile from the TFTP server. You can configure the Cisco ATA 186 to
  • Cisco ATA186-I1 | Installation Guide - Page 51
    access to the Cisco ATA 186, you can power cycle the Cisco ATA 186 to update the profile from TFTP server. About Profile and Configuration Security This section includes information on passwords and other security methods. Passwords To password-protect your Cisco ATA 186: OL-1267-01 Cisco ATA 186
  • Cisco ATA186-I1 | Installation Guide - Page 52
    3 Configuring the Cisco ATA 186 Step 1 Step 2 Set the UIPassword parameter to a numeric password by using the web server interface or TFTP profiling. You will be prompted for a password when you try to access the web server or a configurable IVR parameter. • In web server mode, enter the password
  • Cisco ATA186-I1 | Installation Guide - Page 53
    the corresponding parameters in the local box profile (for example, the DNS1IP, DNS2IP, TftpURL, and NTPIP parameters). If you are not using DHCP, you must manually enter the IP address, network route address, and subnet mask. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 3-9
  • Cisco ATA186-I1 | Installation Guide - Page 54
    Configuring the Cisco ATA 186 Configuring Codec Options You can configure the various Codec call options for use with the Cisco ATA 186. Note The Cisco ATA 186 can support two simultaneous G.723 calls or one G.729A call. When using G.729A, the second line must use G.711 u-law or a-law. The default
  • Cisco ATA186-I1 | Installation Guide - Page 55
    . About H.323-Specific Configurations The Cisco ATA 186 uses ITU H.323, Version 2 as the default signaling protocol. When operating in H.323 mode, the Cisco ATA 186 registers with a gatekeeper to handle call control services. A full registration request (RRQ) is performed at power-up. In order to
  • Cisco ATA186-I1 | Installation Guide - Page 56
    the gatekeeper as you would for any IP phone or Voice over IP (VoIP) configuration. The default configuration is IP routing off. Enabling IP Routing To enable IP routing so that you can run Cisco IOS software, enter: ip routing Cisco ATA 186 Installation and Configuration Guide 4-2 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 57
    -5ess voice rtp send-rcv Configuration depends on your WAN connection. The following example shows a 24-channel PRI connected to a T1 VIC slot: controller T1 0 framing esf clock source linelinecode b8zs pri-group timeslots 1-24 OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 4-3
  • Cisco ATA186-I1 | Installation Guide - Page 58
    by using prepending: Step 1 Step 2 From the web server interface, enter 4 in the Authenticate Method field. Enter the digits to be prepended in the associated PIN field. For example, if you enter the dial string 5551212 in line 0 and the Cisco ATA 186 is configured with 1234 in the PWD0 field, the
  • Cisco ATA186-I1 | Installation Guide - Page 59
    value in seconds, AltGkTimeOut, to enable the feature if non-zero value is used. The Cisco ATA 186 supports the Alternate Gatekeeper list in the GCF/GRJ, ACF/ARJ, RCF/RRJ, and DRJ RAS messages. See Appendix B, "Parameters and Defaults" for more information. About SIP-Specific Configurations The
  • Cisco ATA186-I1 | Installation Guide - Page 60
    or URL listed. The proxy routes to the end IP address. About NAT Support with SIP The following three parameters allow the Cisco ATA 186 to be used behind a firewall or a network address translation (NAT) device to access a SIP proxy server or user agent outside the firewall to register and make
  • Cisco ATA186-I1 | Installation Guide - Page 61
    RTP media streams. This parameter is only used for the purposes of SIP support behind a NAT. NATIP The NATIP configuration parameter specifies the WAN IP of the NAT. Specify the LAN IP in the StaticRoute configuration parameter. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 4-7
  • Cisco ATA186-I1 | Installation Guide - Page 62
    About NAT Support with SIP Chapter 4 Protocol-Specific Configurations Cisco ATA 186 Installation and Configuration Guide 4-8 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 63
    . In the case of call waiting, the second caller hears a busy signal. You can also configure your system to have the services disabled by default and enabled on a call-by-call basis. This is done in the 32-bit "Call Features" plan. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 5-1
  • Cisco ATA186-I1 | Installation Guide - Page 64
    1 Step 2 Dial the first number. When the person you called answers, perform a "hook flash"; that is, hang up quickly and pick up the phone quickly. This will put the first person you called on hold and you will hear a dial tone. Cisco ATA 186 Installation and Configuration Guide 5-2 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 65
    also press 3 later during the call to conference. Performing a hook flash and pressing 1 hangs up the first caller and answers the second call. If there is no answer after one minute, the caller will hear 3 beeps and a busy signal. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 5-3
  • Cisco ATA186-I1 | Installation Guide - Page 66
    . In SIP, the Cisco ATA 186 handles these services. There are 3 types of call forwarding. • Forward Unconditional-forwards every call that comes in. • Forward When Busy-forwards calls when the line is busy. • Forward on No Answer-forwards calls when the telephone is not answered after the configured
  • Cisco ATA186-I1 | Installation Guide - Page 67
    Return. About Calling Line Identification Presentation Calling Line Identification Presentation (CLIP) shows your identity to callers with Caller ID. Calling Line Identification Presentation in the U.S. Press *82 to activate CLIP. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 5-5
  • Cisco ATA186-I1 | Installation Guide - Page 68
    in the U.S. In the U.S., press *67 to activate CLIR. This feature is disabled when you hang up. Calling Line Identification Restriction in Sweden In the U.S., press *31# to activate CLIR. This feature is disabled when you hang up. Cisco ATA 186 Installation and Configuration Guide 5-6 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 69
    software, name your files by using all lowercase letters. Both methods require software available from cisco.com. About Upgrading from Release 1.xx to Release 2.0 Caution Release 2.0 is not backward-compatible with Release 1.xx. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 6-1
  • Cisco ATA186-I1 | Installation Guide - Page 70
    that of the client Cisco ATA 186. • -any2-allow upgrade regardless of software type and version. • -d1,-d2,-d3-set level of detailed description for debugging. Example: ata186us -h123.456.789.100 -p5786 -quiet yj2e112.kup yj2e112.el Cisco ATA 186 Installation and Configuration Guide 6-2 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 71
    enter: ata186us software_file_name. zup -d1 -any2 Press the function button to go to the configuration menu. Caution Step 5 will begin the upgrade process. Do not cancel the process or unplug the power cord at any time during the upgrade process; doing so can permanently damage your Cisco ATA 186
  • Cisco ATA186-I1 | Installation Guide - Page 72
    you have upgraded your Cisco ATA 186. Timesaver When upgrading many Cisco ATA 186s, you can save the software upgrade commands in your telephone's speed-dial and use them after accessing the Cisco ATA 186 voice menu. Upgrading the Software from a TFTP Server You can configure the Cisco ATA 186 to
  • Cisco ATA186-I1 | Installation Guide - Page 73
    6 Upgrading the Cisco ATA 186 Software About the Software Upgrade Process Note To help you identify the correct files to place on your TFTP server, the TFTP-method file containing the Cisco ATA 186 software has a ".kxz" extension. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 6-5
  • Cisco ATA186-I1 | Installation Guide - Page 74
    About the Software Upgrade Process Chapter 6 Upgrading the Cisco ATA 186 Software Cisco ATA 186 Installation and Configuration Guide 6-6 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 75
    gateway must be configured at both ends to detect the FAX tone and switch codec. The Cisco ATA 186 supports two G.711 upspeed methods for FAX passthorough: • The Cisco proprietary codec switch using NSE packets and RTP detection. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 7-1
  • Cisco ATA186-I1 | Installation Guide - Page 76
    means use NSE payload-type number 100, G.711u-law codec, and no redundancy in FAX passthrough mode. AudioMode Set to 0xXXXX0015 for line 1, or 0x0015XXXX for line 2, (X=don't care). This setting enables FAX tone detection. Cisco ATA 186 Installation and Configuration Guide 7-2 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 77
    communication between the Cisco gateway and the specified Cisco ATA 186 using the dial-peer level commands: dial-peer voice tag voip modem passthrough { NSE [payload-type number] codec {g711ulaw | g711alaw} [redundancy] | system} OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 7-3
  • Cisco ATA186-I1 | Installation Guide - Page 78
    the Cisco ATA 186 configuration. On the Cisco gateway, enter: no modem passthrough About FAX Mode Some users might want to set one or both lines of the Cisco ATA 186 to pure G.711 FAX mode. This mode allows the FAX machine connected to the Cisco ATA 186 to communicate directly with the FAX machine
  • Cisco ATA186-I1 | Installation Guide - Page 79
    the Fax. The next call will automatically revert to normal mode. Configuring the Cisco Gateway for FAX Mode On the Cisco Gateway, disable both FAX relay and FAX Passthrough with the following commands: no fax relay no modem passthrough OL-1267-01 Cisco ATA 186 Installation and Configuration Guide
  • Cisco ATA186-I1 | Installation Guide - Page 80
    About FAX Mode Chapter 7 Using the FAX Passthrough Feature Cisco ATA 186 Installation and Configuration Guide 7-6 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 81
    3 Lift the primary line telephone handset. If you are not in SIP mode, enter your user ID (UID). If you hear a dial tone, your Cisco ATA 186 is properly configured. Making a Call Note The dial plan described in these instructions is the default plan. You can configure your Cisco ATA 186 to use
  • Cisco ATA186-I1 | Installation Guide - Page 82
    telephone call by using the second handset connected to the Cisco ATA 186. The Cisco ATA 186 can support two simultaneous G.723 calls or one G.729A call. When using G.729A, the second line must use G.711 u-law or a-law. The default voice codec is G.723. Troubleshooting Tips The suggestions in this
  • Cisco ATA186-I1 | Installation Guide - Page 83
    at power up reset. Action If you are using TFTP for provisioning, do not use the Web Server Interface or IVR to modify the value of your Cisco ATA 186 profile. Only use the Web Server Interface or IVR to initially configure the Cisco ATA 186 to use TFTP for provisioning. Cisco ATA 186 Installation
  • Cisco ATA186-I1 | Installation Guide - Page 84
    then the Cisco ATA 186 is operating in pure IP to IP mode, and the Cisco ATA 186 can be addressed only by IP address. Action Make sure that UID0 and UID1 are set to the applicable values (telephone numbers) to get a dial tone on each line. Cisco ATA 186 Installation and Configuration Guide 8-4 OL
  • Cisco ATA186-I1 | Installation Guide - Page 85
    and Troubleshooting the Cisco ATA 186 Symptoms and Actions Symptom Unable to access the web configuration page. Possible Cause Software versions earlier than 2.0 require the web configuration page to be enabled using option 80# on the IVR. Action Upgrade the software. Symptom FAX passthrough
  • Cisco ATA186-I1 | Installation Guide - Page 86
    . Possible Cause The SIP protocol or SIP Registration are not enabled. Action Make sure that you have enabled the SIP protocol by setting the UseSIP parameter. If you are using proxy, enable SIP registration (for authentication). Cisco ATA 186 Installation and Configuration Guide 8-6 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 87
    prompt returns Upgrade failed message. Possible Cause You have entered an incorrect IP address. Action Enter the correct IP address. Symptom No dial tone. Possible Cause No user ID was entered. Action Enter the correct user ID. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 8-7
  • Cisco ATA186-I1 | Installation Guide - Page 88
    Contacting TAC Chapter 8 Testing and Troubleshooting the Cisco ATA 186 Symptom Incorrect dial tone. Possible Cause You installed a template for a country other than your own. Check the web interface for your Dial Plan. The default is U.S. Action Install the correct country template. Mass
  • Cisco ATA186-I1 | Installation Guide - Page 89
    . Caution For security reasons, Cisco recommends that you do not use the web interface over the public network. Disable the web interface by using the UIPassword parameter before the Cisco ATA 186 leaves the service provider site. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide 8-9
  • Cisco ATA186-I1 | Installation Guide - Page 90
    Contacting TAC Chapter 8 Testing and Troubleshooting the Cisco ATA 186 8-10 Cisco ATA 186 Installation and Configuration Guide OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 91
    Menu Options This Appendix contains a list of the Voice Menu options for the Cisco ATA 186. Note Press # after you enter the item number. Table A-1 Voice Menu the build date of the Cisco ATA 186 software Not currently available OL-1267-01 Cisco ATA 186 Installation and Configuration Guide A-1
  • Cisco ATA186-I1 | Installation Guide - Page 92
    Description This command controls whether the Cisco ATA 186 can automatically obtain configuration parameters from a server over the network. 411 916 917 320 35 Select the number of frames per packet to be transmitted when using the audio codec G.723.1 or G.729A. 91 (H.323) 5 Enter the
  • Cisco ATA186-I1 | Installation Guide - Page 93
    received data. The call-receiving station automatically adjusts to the call-initiating station's audio codec type if the call-receiving station supports that audio codec. (SIP) (SIP) (SIP) (SIP) Select the signalling protocol. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide A-3
  • Cisco ATA186-I1 | Installation Guide - Page 94
    as the audio codec type for transmitting. Enter the User ID (telephone number) for the Phone 2 port. Change or upgrade the voice prompt language to English. See Chapter 6, "Upgrading the Cisco ATA 186 Software" for more information. Cisco ATA 186 Installation and Configuration Guide A-4 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 95
    Number Item Number 305 Description 3 Enter the User ID (telephone number) for the Phone 1 port. 123 Listen to the version number of the Cisco ATA 186 software. Table A-2 Voice Menu Options in Numerical Order Item Number 1 2 3 4 5 6 10 11 Option IP Address Network Route Address UID 0 PWD
  • Cisco ATA186-I1 | Installation Guide - Page 96
    3=G.729A Tx Codec 0=G.723.1 (default) 1=G.711A 2=G.711µ 3=G.729A Description Enter the User ID (telephone number) for the Phone 2 port. Enter the password associated with the second gatekeeper account. This command controls whether the Cisco ATA 186 can automatically obtain configuration parameters
  • Cisco ATA186-I1 | Installation Guide - Page 97
    Registration On (SIP) SIP Max Number of Redirects (SIP) SIP Outbound Proxy (SIP) Gatekeeper time to live (H.323) Enter the amount of idle time before the gatekeeper times out. Alternate Gatekeeper timeout (H.323) UDP TOS Bits OL-1267-01 Cisco ATA 186 Installation and Configuration Guide
  • Cisco ATA186-I1 | Installation Guide - Page 98
    DNS 2 IP Build Information ToConfig 0=provisioned 1=new (default) Description Enable logging of SIP messages Not currently available Listen to the build date of the Cisco ATA 186 software See Appendix B, "Parameters and Defaults" Cisco ATA 186 Installation and Configuration Guide A-8 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 99
    Appendix A Voice Menu Options Table A-2 Voice Menu Options in Numerical Order Item Number 80002 7387277 Option CfgInterval Set Password Description OL-1267-01 Cisco ATA 186 Installation and Configuration Guide A-9
  • Cisco ATA186-I1 | Installation Guide - Page 100
    Appendix A Voice Menu Options A-10 Cisco ATA 186 Installation and Configuration Guide OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 101
    line indicates a comment. All parameter/value pairs are optional but might be needed for the Cisco ATA 186 to function properly if a value has not already been programmed. Where an IVR Access bits in 32-bit integer) • integer (32 bit integer). Cisco ATA 186 Installation and Configuration Guide B-1
  • Cisco ATA186-I1 | Installation Guide - Page 102
    page or IVR interface. If set to non-zero, then you must enter the value of UIPassword to access the web page and IVR. 7387277 Note When UIPassword contains letters, you cannot enter the password from the telephone keypad. Default 0 Cisco ATA 186 Installation and Configuration Guide B-2 OL-1267
  • Cisco ATA186-I1 | Installation Guide - Page 103
    Table B-2 TFTP Provisioning Parameters and Defaults Parameter CfgInterval EncryptKey Value Type Description IVR Access Code Specifies the number of seconds (interval) between each configuration update. For example, when using TFTP for provisioning, the Cisco ATA 186 contacts TFTP each time the
  • Cisco ATA186-I1 | Installation Guide - Page 104
    TFTP for provisioning; 305 0 means do not. Default 0 0 1 There are two additional parameters that are used to control the upgrade of the firmware code and language. The values of these parameters depend on the software release. Cisco ATA 186 Installation and Configuration Guide B-4 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 105
    stored image ID means a forced upgrade is needed). • hardware_version- 0x301. The hardware version must match exactly for upgrade to take place. • tftp_ip_address, tftp_port-TFTP IP and port address where the firmware can be found. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide B-5
  • Cisco ATA186-I1 | Installation Guide - Page 106
    ,0x0400,0x0200,192.168.2.170,69,0x1,ef2_200h.kxz 1= upgrade policy 0x031=hardware version 0x0400=software type 0x0200=software version 192.168.2.170=tftp_ip_address 69=TFTP port 0x1=image id ef2_200h.kxz=firmware image file name Cisco ATA 186 Installation and Configuration Guide B-6 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 107
    IVR Access Code Default Bitmap Authentication method. Possible values 92 are: 0x00000000 • bit 0-1 (mask 0x3): 0 for no authentication, 1 for authentication • Cisco registration level security (H.235), 2 for Cisco Systems admission level security. • bit 2 (mask 0x4): prefix password
  • Cisco ATA186-I1 | Installation Guide - Page 108
    { bit 3-6 (mask 0x78): start digit (12) bit 7-10 (mask 0x780): end digit (14) bit 11 (mask 0x800): polarity reversal (1) bit 12-16 (mask 0x1f000): max no. of digits (15) } - Sweden=0x0ff61 - Denmark=0x0fde1 - USA=0x19e60 Cisco ATA 186 Installation and Configuration Guide B-8 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 109
    . Possible 317 values are: 0x003c33d0 • bit 0-5 (mask 0x3f): max no of digits (16) • bit 6-11 (mask 0xfc0): max no of characters (15) • bit 12-17 (mask 0x3f000): special chars (3) • bit 18-21 (mask 0x3c0000): ack digit (15) OL-1267-01 Cisco ATA 186 Installation and Configuration Guide B-9
  • Cisco ATA186-I1 | Installation Guide - Page 110
    to remove the registration before adding a new one. • bit 17 (mask 0x20000): 1 enables SIP call forwarding to be performed by the Cisco ATA 186. • bit 18 (mask 0x40000): 1 enables SIP call return performed by the Cisco ATA 186. B-10 Cisco ATA 186 Installation and Configuration Guide OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 111
    IVR Access Code Default Boolean Can be used to automatically set the IP 20 1 address, network a URL such as sip.cisco.com, or sip.ata.cisco.com:5061. For IP entered. 2: if three '.' are seen, then assume IP address is entered. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide B-11
  • Cisco ATA186-I1 | Installation Guide - Page 112
    0x1) is set to 1, always use the internally generated TFTP file name. If Bit 1 (mask 0x2) is set to 1, do not perform static network router probing at cold start. IVR Access Code Default 300 0 141 0.0.0.0 35 2 323 0x2 B-12 Cisco ATA 186 Installation and Configuration Guide OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 113
    . Possible values are: • 0-G.723 (can be selected only if LBRCodec is set to 0). • 1-711a. • 2-G.711u. • 3-729a (can be selected only if LBRCodec is set to 3). IVR Access Code Default 304 0x00000000 PWD0=4 0 PWD1=14 36 0 OL-1267-01 Cisco ATA 186 Installation and Configuration Guide B-13
  • Cisco ATA186-I1 | Installation Guide - Page 114
    after which, when there is no answer, the Cisco ATA 186 rejects the incoming call. Range=0 to 63 in 10 seconds, 0=never times out. Default: 6 (60 seconds). No Answer Timeout (bits 20-25): time to declare no answer and initiate call forwarding on no answer (used in SIP only at present). Range=0 to
  • Cisco ATA186-I1 | Installation Guide - Page 115
    , if TimeZone > 12 Transmitting audio codec preference. 37 1 Possible values are: • 0-G.723 (can be selected only if LBRCodec is set to 0). • 1-G.711A. • 2-G.711u. • 3-G.729A (can be selected only if LBRCodec is set to 3). OL-1267-01 Cisco ATA 186 Installation and Configuration Guide B-15
  • Cisco ATA186-I1 | Installation Guide - Page 116
    1 means use Login id specified in 93 0 LoginId0 and LoginId1 and 0 means not. For H323, this field is needed if autm is set to 1. For SIP, UID0 and UID1 will be used for authentication if this is 0. B-16 Cisco ATA 186 Installation and Configuration Guide OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 117
    redirection. 205 5 Integer Base port to receive RTP media; currently 202 only used to support SIP behind a NAT. 10000 IP WAN address of the attached router/NAT; 200 0.0.0.0 currently only used to support SIP behind a NAT. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide B-17
  • Cisco ATA186-I1 | Installation Guide - Page 118
    to indicate a port. Integer Port to listen for incoming SIP requests. 201 5060 Integer Seconds between registration renewal. 203 3600 Integer Enable SIP registration. 204 0 Boolean Use SIP mode (default H.323). 38 0 B-18 Cisco ATA 186 Installation and Configuration Guide OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 119
    audio mode parameters and defaults that you can use to provision your Cisco ATA 186. The Audio Mode format is bitmap. The IVR access code is 312. The default format is 0x00150015. enable rcv, decode other SDP info, always send) (1) OL-1267-01 Cisco ATA 186 Installation and Configuration Guide C-1
  • Cisco ATA186-I1 | Installation Guide - Page 120
    C Audio Mode Parameters and Defaults • bits 6-7 mask 0xc0: HookflashMethod: - 0=disable sending hookflash - 1=by negotiation - 2=always send hookflash - 3=use Q931 to send user keypad input (DTMF or hookflash) information (0) Cisco ATA 186 Installation and Configuration Guide C-2 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 121
    for before the dial string is automatically sent. • The timeout (in seconds) between when the last digit is entered and when the Cisco ATA 186 sends the dial string. The timeout can be programmed to change value in mid-dial string. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide D-1
  • Cisco ATA186-I1 | Installation Guide - Page 122
    (e.g., a dial plan beginning with *S will be the only one in effect if the user first enters the * key). Note All rules apply in the order listed (whichever rule is completely matched first will immediately send the dial string). Cisco ATA 186 Installation and Configuration Guide D-2 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 123
    manually send the dial string. After the 2nd digit is entered, the timeout before automatic send changes to 7 seconds. The user can enter more digits until the dial string is sent by the timeout or by the user entering the # character. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide
  • Cisco ATA186-I1 | Installation Guide - Page 124
    automatic send is 4 seconds. The terminating character # can be entered at any time to manually send the dial string. The user can enter more digits until the dial string is sent by the timeout or by the user entering the # character. Cisco ATA 186 Installation and Configuration Guide D-4 OL-1267
  • Cisco ATA186-I1 | Installation Guide - Page 125
    entire dial string being sent at timeout, it is sent only as a result of a matching rule or time intended by a matching rule. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide D-5
  • Cisco ATA186-I1 | Installation Guide - Page 126
    Dial Plan Blocking Appendix D Dial Plan Parameters and Defaults Cisco ATA 186 Installation and Configuration Guide D-6 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 127
    use the same bit masks. Paid services indicates which service the user has subscribed to, while call features indicates which feature is statically enabled by the user. Not all supplementary services can be disabled by the user. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide E-1
  • Cisco ATA186-I1 | Installation Guide - Page 128
    and Defaults The valid flags in call features are CLIP_CLIR, CALL_WAITING, and FAXMODE. A subscribed service enable/ answer CLIP Call waiting 3-way calling Blind transfer Consult transfer Caller ID Call return Message waiting indication FAX mode Cisco ATA 186 Installation and Configuration Guide
  • Cisco ATA186-I1 | Installation Guide - Page 129
    to provision your Cisco ATA 186. Call Progress Tone Parameters The call progress tone parameter is used to set the tone and frequency of the call progress tone. This value is expressed as an integer. You cannot configure the call progress tone by using the IVR mode. You must use the web interface or
  • Cisco ATA186-I1 | Installation Guide - Page 130
    0 indicates an on/off tone pattern and causes the Cisco ATA 186 to use the on-time and off-time parameters. • on-time controls the length of time the tone is heard in milliseconds (ms) expressed as an integer from 1 to 0x7FFFFFFF. Cisco ATA 186 Installation and Configuration Guide F-2 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 131
    Appendix F Call Progress Tone Parameters and Defaults Playback Tone • off-time controls the length 0.35 · 32768 · sin (2pi · 440 / 8000) = 4047 The approximate values to enter for level0 and level1 are 3194 and 4047, respectively. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide F-3
  • Cisco ATA186-I1 | Installation Guide - Page 132
    Appendix F Call Progress Tone Parameters and Defaults Table F-1 Volume Levels for a Standard U.S. 600-Ohm Impedance Board Volume Level for One Tone Volume Level 2392,0,0,1600,4000,11200 • AlertTone: 1,30959,0,2392,0,0,2000,6000,0 Cisco ATA 186 Installation and Configuration Guide F-4 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 133
    configured, or deactivated in more than one way. The Cisco ATA 186 allows the behavior of supplementary services to be defined using its "CallCmd" field. Context Command Lists The entry in the "CallCmd" field is a character string composed of a sequence of instructions, called Context-Command-Lists
  • Cisco ATA186-I1 | Installation Guide - Page 134
    , each Context-Command-List has one Context-Identifier followed by one or more Commands. This allows a variable number of actions to be triggered by the relevant user input commands for any state. Each command is composed of an Input-Sequence (which the user will enter when the Cisco ATA 186 is in
  • Cisco ATA186-I1 | Installation Guide - Page 135
    IDLE RINGING DIALING CALLING Reserved (ANSWERING) Reserved (CANCELING) Reserved (DISCONNECTING) WAITHOOK DIALING_HOLDING CALLING_HOLDING Reserved (ANSWERING_HOLDING) Reserved (HOLDING_HOLDING) Reserved (CANCELING_HOLDING) Syntax OL-1267-01 Cisco ATA 186 Installation and Configuration Guide G-3
  • Cisco ATA186-I1 | Installation Guide - Page 136
    Syntax Appendix G Call Commands Table G-1 Context Identifiers (continued) Identifier Y Z a b configuration mode Release the call Answer the incoming call Transfer with consultation Say busy to the caller None Forward all calls to the given number Cisco ATA 186 Installation and Configuration Guide
  • Cisco ATA186-I1 | Installation Guide - Page 137
    commands, the Cisco ATA 186 has a default list of call commands to handle common call scenarios. The default call commands can be overwritten by the provisioned call commands. If any Context/Input-Sequence appears in both the default Call Command string and the manually entered string, the manually
  • Cisco ATA186-I1 | Installation Guide - Page 138
    Commands off-hook; Answer-the-incoming-call Rf;OA; Disconnecting hook-flash; Release-the-call NONE; Sf;OA; Waithook hook-flash; Release-the-call NONE; TD;CAf;OF; Dialing_Holding 0|1|...|9|#|*; Continue-to-dial NONE; hook-flash; Release-the-call NONE; Cisco ATA 186 Installation and Configuration Guide
  • Cisco ATA186-I1 | Installation Guide - Page 139
    ; Waithook_Holding hook-flash; Release-the-call Answer-the-incoming-call; Call Command Behaviors Table G-3 summarizes the differing Call Command behaviors. Note This information is based on the U.S. and Sweden default call commands. OL-1267-01 Cisco ATA 186 Installation and Configuration Guide G-7
  • Cisco ATA186-I1 | Installation Guide - Page 140
    number DIALING: User entering phone number, which R: Abort dialing, restarts dial-tone, and revert to is parsed with the given dial-plan rules PREDIAL;Invalid phone number: Abort dialing, plays fast-busy, and goto WAITHOOK; Cisco ATA 186 Installation and Configuration Guide G-8 OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 141
    out the configuration command, restart dial-tone, and revert to PREDIAL CALLING: Phone number is sent; R: Cancel the outgoing call, restarts dial-tone, and Cisco ATA 186 is waiting for response from the revert to PREDIAL far end OL-1267-01 Cisco ATA 186 Installation and Configuration Guide G-9
  • Cisco ATA186-I1 | Installation Guide - Page 142
    current call and goto IDLE (in which Cisco ATA 186 automatically starts ringing the phone, and goto RINGING); AFE hangs up: Goto WAITHOOK_ALERTING, continue to play CWT; WFE cancels the call: Stop CWT and revert to CONNECTED G-10 Cisco ATA 186 Installation and Configuration Guide OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 143
    to the other, drop out of the call, and goto PREDIAL;) PREDIAL_HOLDING: Cisco ATA 186 user places a connected call on-hold and prepares to dial a second number; Cisco ATA 186 plays dial-tone US *,#: Stop dial-tone, goto CONFIG_HOLDING, and prepare to collect a configuration command;0-9: Stop dial
  • Cisco ATA186-I1 | Installation Guide - Page 144
    )All RegionsR or any unrecognized sequence: Abort configuration, restarts dial-tone, and goto to PREDIAL_HOLDING A complete configuration sequence: Carries out the command, and goto PREDIAL_HOLDING DIALING_HOLDING: Cisco ATA 186 user entering a second phone number to call while placing a connected
  • Cisco ATA186-I1 | Installation Guide - Page 145
    G Call Commands Syntax U.S. Call Command The default U.S. Call command is: -configuration-mode NONE; Df;EB; Connected hook-flash; Hold-the-active-call Seizure; Ff;EP; Connected_Alerting hook-flash; Hold-the-active-call Answer-the OL-1267-01 Cisco ATA 186 Installation and Configuration Guide G-13
  • Cisco ATA186-I1 | Installation Guide - Page 146
    number NONE #75v#; Forward-on-no-answer-to-the-given-number NONE #73 fax-mode-for-the-next-call NONE; Uh;GQ; Calling_Holding on-hook; Cancel-the-call-attempt Transfer-with-consultation;; Sweden Call Command configuration-mode NONE; G-14 Cisco ATA 186 Installation and Configuration Guide OL-1267-01
  • Cisco ATA186-I1 | Installation Guide - Page 147
    -flash4; Disconnect-the-call Transfer-with-consultation; Af4;HQ; Conference hook-flash4; Disconnect-the-call Transfer-with-consultation; I*31#;gA#31#;gA*90*v#;OI; Configuring_Holding Cisco ATA 186 Installation and Configuration Guide G-15
  • Cisco ATA186-I1 | Installation Guide - Page 148
    Commands Configuring -to-the-given-number NONE; *61*v#; Forward-on-no-answer-to-the-given-number NONE; *67*v#; Forward-on-busy- fax-mode-for-the-next-call NONE Uh;GQ; Calling_Holding on-hook; Cancel-the-call-attempt Transfer-with-consultation G-16 Cisco ATA 186 Installation and Configuration Guide
  • Cisco ATA186-I1 | Installation Guide - Page 149
    and Acronyms Guide. Comfort Noise Generation. Digital Signal Processor. Dual Tone Multi-Frequency. FAX over IP Foreign Exchange Office. An FXO connects to a central office - this is the interface a standard phone offers. Foreign Exchange Station Cisco ATA 186 Installation and Configuration Guide H-1
  • Cisco ATA186-I1 | Installation Guide - Page 150
    telephony. Subscriber Line Interface Circuit. An IC providing central office-like telephone interface functionality. Small Office / Home Office. Voice Activity Detection. Voice over Internet Protocol. A packet based network protocol. Cisco ATA 186 Installation and Configuration Guide H-2 OL-1267
  • Cisco ATA186-I1 | Installation Guide - Page 151
    B-3 Cisco.com xviii Cisco ATA 186 Description 1-1 Codec 3-10 codec 7-3 OL-1267-01 INDEX Compliance 1-9 Configuration Requirements 3-1 ConnectMode 7-2 Conventions xii cross software type upgrade B-5 D default upgrade B-5 DHCP B-11 DHCP_VENDOR_CLASS_ID 3-8 DHCP network 3-2 dial peer level command
  • Cisco ATA186-I1 | Installation Guide - Page 152
    pass-through 8-5 Features 1-4 firmware_image_file_name B-5, B-6 Firmware Upgrade Parameters B-5 force upgrade B-5 Function Button 1-3, 2-11 function button 3-2, 8-3 G G.711 FAX mode 7-1, 7-4 gateway 3-1 GkOrProxy B-11 GkTimeToLive B-17 glossary H-1 H H.323 B-17 hardware_version B-5 How This Guide
  • Cisco ATA186-I1 | Installation Guide - Page 153
    1-1 P parameters and defaults B-1 Password B-13 Polarity B-13 Power 1-8 Power adapto 1-8 Product Disposal Warning xx Product Features 1-4 Protocols 1-7 provisioning B-1 Provisioning Using the Voice Configuration Menu 3-4 OL-1267-01 Provisioning Via the Internal Web Server Interface 3-4 PWD0 B-13
  • Cisco ATA186-I1 | Installation Guide - Page 154
    V Verification 2-11 Voice Configuration Menu 3-1, 3-2, 3-4 voice menu options A-1 voip 7-3 Voltage 1-8 W warning symbol, meaning of xiii Web browser 3-1 Web Server Interface 3-4 Who Should Read This Guide xi World Wide Web xvii IN-4 Cisco ATA 186 Installation and Configuration Guide OL-1267-01
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Tel:
408 526-4000
800 553-NETS (6387)
Fax:
408 526-4100
Cisco ATA 186 and Cisco 188
Installation and Configuration
Guide
August, 2002
Customer Order Number:
Text Part Number: OL-1267-01