Cisco MDS-9124 Troubleshooting Guide - Page 401
Displaying Passive Mode Set on Both Sides of the FCIP Tunnel with the CLI, no passive-mode
View all Cisco MDS-9124 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 401 highlights
Chapter 20 Troubleshooting IP Storage Services FCIP Issues Send documentation comments to [email protected] Trunk vsans (up) (1-2) Trunk vsans (isolated) () Trunk vsans (initializing) () Using Profile id 21 (interface GigabitEthernet2/1) Peer Information Peer Internet address is 10.10.10.2 and port is 3225 Special Frame is disabled Maximum number of TCP connections is 2 Time Stamp is disabled B-port mode disabled TCP Connection Information 2 Active TCP connections Control connection: Local 10.10.11.2:65330, Remote 10.10.10.2:3225 Data connection: Local 10.10.11.2:65332, Remote 10.10.10.2:3225 Displaying Passive Mode Set on Both Sides of the FCIP Tunnel with the CLI In the following example, passive mode is set on both sides of the FCIP tunnel. module-2# Mar 14 23:49:06 port1: 1870:FCIP21: SUP-> Set Port mode 1 Mar 14 23:49:06 port1: 1871:FCIP21: SUP-> Port VSAN (1) already set to same value Mar 14 23:49:06 port1: 1872:FCIP21: SUP-> Trunk mode (1) already set to same value Mar 14 23:49:06 port1: 1873:FCIP21: SUP-> Enable tunnel ADMIN UP Mar 14 23:49:06 port1: 1874:FCIP21: Try to Bring UP the Tunnel Mar 14 23:49:06 port1: 1875:FCIP21: Start TCP listener with peer: 10.10.10.2:3225 Mar 14 23:49:06 port1: 1876:FCIP: Create a new listener object for 10.10.11.2:3225 Mar 14 23:49:06 port1: 1877:FCIP: Create FCIP Listener with local info: 10.10.11.2:3225 Mar 14 23:49:06 port1: 1878:FCIP21: Passive mode set, don't initiate TCP connection (A TCP connection will not be established when passive mode is set.The Gigabit Ethernet port will only listen.) MDS2# show interface fcip 21 fcip21 is down (Link failure or not-connected) Hardware is GigabitEthernet Port WWN is 20:42:00:0b:5f:d5:9f:c0 Admin port mode is auto, trunk mode is on vsan is 1 Using Profile id 21 (interface GigabitEthernet2/1) Peer Information Peer Internet address is 10.10.10.2 and port is 3225 Passive mode is enabled (Passive mode is set, so a TCP connection will not be established.) Special Frame is disabled MDS1# show interface fcip 21 fcip21 is down (Link failure or not-connected) Hardware is GigabitEthernet Port WWN is 20:42:00:05:30:00:59:de Admin port mode is auto, trunk mode is on vsan is 1 Using Profile id 21 (interface GigabitEthernet2/1) Peer Information Peer Internet address is 10.10.11.2 and port is 3225 Passive mode is enabled (Both sides are set to passive mode. You must change one or both sides to no passive-mode under the FCIP interface.) Special Frame is disabled MDS2(config)# interface fcip 21 MDS2(config-if)# no passive-mode OL-9285-05 Cisco MDS 9000 Family Troubleshooting Guide, Release 3.x 20-27