Cisco RV042 User Guide
Cisco RV042 - Small Business Dual WAN VPN Router Manual
UPC - 745883560530
View all Cisco RV042 manuals
Add to My Manuals
Save this manual to your list of manuals |
Cisco RV042 manual content summary:
- Cisco RV042 | User Guide - Page 1
10/100 4-Port VPN Router Model: RV042 USER GUIDE BUSINESS SERIES - Cisco RV042 | User Guide - Page 2
and certain other countries. Copyright © 2008 Cisco Systems, Inc. All rights reserved. Trend Micro, InterScan, and ProtectLink are trademarks of Trend Micro Incorporated. Other brands and product names are trademarks or registered trademarks of their respective holders. 10/100 4-Port VPN Router i - Cisco RV042 | User Guide - Page 3
Table of Contents 10/100 4-Port VPN Router Chapter 1: Introduction 1 Introduction to the Router 1 Introduction to VPNs 1 VPN Examples 1 VPN Router to VPN Router 1 Computer (using VPN client software) to VPN Router 2 Chapter 2: Product Overview 3 Front Panel 3 Back Panel 3 Right Side - Cisco RV042 | User Guide - Page 4
10/100 4-Port VPN Router Table of Contents One-to-One NAT 16 Setup > MAC Clone 16 MAC Clone 17 Setup > DDNS 17 DDNS 17 Setup > Advanced Routing 18 Advanced Routing 18 DHCP > Setup 19 Setup 20 DHCP > Status 21 Status 21 System Management Tab > Dual-WAN 21 Dual-WAN 21 System Management > - Cisco RV042 | User Guide - Page 5
Rule Setup 54 Support 56 Manual 56 Linksys Web Site 56 Logout 56 Appendix A: Troubleshooting 57 Appendix B: Linksys QuickVPN for Windows 2000, XP, or Vista 58 Introduction 58 Computer (using VPN client software) to VPN Router 58 Linksys QuickVPN Instructions 58 Router Configuration 58 - Cisco RV042 | User Guide - Page 6
Contents 10/100 4-Port VPN Router Configuration of PC 1 and PC 2 63 Configuration when the Remote Gateway Uses a Dynamic IP Address 64 Configuration of the RVL200 64 Configuration of the RV042 64 Configuration of PC 1 and PC 2 65 Configuration when Both Gateways Use Dynamic IP Addresses 65 - Cisco RV042 | User Guide - Page 7
91 FCC Statement 91 Safety Notices 91 Industry Canada Statement 91 Avis d'Industrie Canada 91 User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE 92 Appendix L: Contact Information 96 10/100 4-Port VPN Router vi - Cisco RV042 | User Guide - Page 8
be installed. NOTE: The 10/100 4-Port VPN Router supports IPSec VPN client software, including the Linksys QuickVPN software. (For more information, refer to "Appendix B: Linksys QuickVPN for Windows 2000, XP, or Vista".) For a PPTP VPN tunnel, the 10/100 4-Port VPN Router and any computer running - Cisco RV042 | User Guide - Page 9
if she were physically connected. Off-Site Internet VPN Router Central Office Notebook with VPN Client Software Computer to VPN Router For additional information and instructions about creating your own VPN, visit the Linksys website at www.linksys.com. Introduction 10/100 4-Port VPN Router 2 - Cisco RV042 | User Guide - Page 10
problems with the Router and have tried all other troubleshooting measures, press and hold in the Reset button for 30 seconds. This will restore the factory defaults and clear all of the Router's custom settings. You can also reset the Router to factory defaults using the System Management > Factory - Cisco RV042 | User Guide - Page 11
precise spacing. Wall Mounting Template Cable Connections To connect network devices to the Router, follow these instructions: 1. Before you begin, make sure that all of your hardware is powered off, including the Router, computers, switches, and cable or DSL modem. 10/100 4-Port VPN Router 4 - Cisco RV042 | User Guide - Page 12
is connected properly. 7. Power on your computers and other network devices. Connect to the Internet Port Connect to the DMZ/Internet Port 4. Power on the cable or DSL modem. If you have a network device connected to the DMZ/Internet port, power on the network device. 10/100 4-Port VPN Router 5 - Cisco RV042 | User Guide - Page 13
Router's default IP address, 192.168.1.1, in the Address field. Press the Enter key. Address Bar NOTE: If the Remote Management feature on the Firewall > General screen has been enabled, then users with administrative privileges can remotely access the web-based utility. Use http:// - Cisco RV042 | User Guide - Page 14
, you can upgrade the Router's firmware if you want to purchase and use this optional service. Refer to "Appendix F: Firmware Upgrade" for instructions. Go buy To purchase a license to use this service, click Go buy.You will be redirected to a list of Linksys resellers on the Linksys website. Then - Cisco RV042 | User Guide - Page 15
on the Setup > Network screen. 10/100 4-Port VPN Router DDNS It shows the DDNS settings of the Router's WAN port(s) and hyperlinks to the Setup > DDNS screen. DMZ Host It shows the DMZ private IP address and hyperlinks to the Setup > DMZ Host screen. The default is Disabled. Firewall Setting - Cisco RV042 | User Guide - Page 16
this option to enable the Multiple Subnet feature. Then click Add/Edit to create or modify subnet(s). A new screen appears. 10/100 4-Port VPN Router Create or Modify a Subnet LAN IP Address Enter the LAN IP address. Subnet Mask Enter the subnet mask. For example, the current LAN settings show the - Cisco RV042 | User Guide - Page 17
IP Address 192.168.2.193 •• Subnet Mask 255.255.255.192 Click Add to List. Then click Save Settings. Dual-WAN/DMZ Setting Before configuring the WAN Connection Type settings, select Dual WAN or DMZ. The Dual WAN setting allows you to simultaneously connect two broadband connections to the Router - Cisco RV042 | User Guide - Page 18
Tunneling Protocol (PPTP) is a service used in Europe, Israel, and other countries. PPPoE User Name and Password Enter your account's User Name and Password. The maximum number of characters is 60. 10/100 4-Port VPN Router PPTP Specify WAN IP Address Enter the external IP address of the Router - Cisco RV042 | User Guide - Page 19
this option and configure the following: •• IP Range for DMZ port Enter the starting and ending IP addresses. Click Save Settings to save your changes, or click Cancel Changes to undo them. Setup > Password The Router's default User Name and Password is admin, and Linksys strongly recommends that - Cisco RV042 | User Guide - Page 20
Advanced Configuration Daylight Saving To use the daylight saving feature, select Enabled. Enter the Month and Day of the start date, and then enter the Month and Day of the end date. NTP Server Enter the URL or IP address of the NTP server. The default is time.nist.gov. Manual Setup > Password - Cisco RV042 | User Guide - Page 21
. The packets will simply be forwarded through the Router. Service Select the Service you want. IP Address Enter the IP address of the server that you want the Internet users to access. 10/100 4-Port VPN Router Service Management Service Name Enter a name. Protocol Select the protocol it - Cisco RV042 | User Guide - Page 22
Cancel Changes to undo them. Setup > UPnP Universal Plug and Play (UPnP) can be used to set up public services on your network. When the UPnP function is enabled, Windows XP or Vista can modify these entries via UPnP. 10/100 4-Port VPN Router Service Management Service Name Enter a name. Protocol - Cisco RV042 | User Guide - Page 23
, which is a 12-digit code assigned to a unique piece of hardware for identification. The MAC Clone feature "clones" your network adapter's MAC address onto the Router, so you don't have to call your ISP to change the registered MAC address to the Router's MAC address. 10/100 4-Port VPN Router 16 - Cisco RV042 | User Guide - Page 24
the Dual WAN feature, then you will have two ports, WAN1 and WAN2, available for DDNS service. DDNS Service The DDNS feature is disabled by default. To enable this feature, select DynDNS.org, 3322.org, or Oray.net PeanutHull DDNS. 10/100 4-Port VPN Router Setup > DDNS > DynDNS.org User name - Cisco RV042 | User Guide - Page 25
Changes to undo them. Setup > Advanced Routing The Advanced Routing screen allows you to configure the dynamic and static routing settings. Setup > Advanced Routing Advanced Routing Dynamic Routing The Router's dynamic routing feature can be used, so the Router will automatically adjust to physical - Cisco RV042 | User Guide - Page 26
, do one of the following: •• Configure the IP address, subnet mask, and DNS settings of every computer on your network. (Make sure you do not assign the same IP address to different computers.) •• Set up a stand-alone DHCP server with the Router as the default gateway. 10/100 4-Port VPN Router 19 - Cisco RV042 | User Guide - Page 27
to view all devices' IP addresses and 10/100 4-Port VPN Router Unknown MAC Addresses List To add an IP address and MAC address set to the Static IP list, select Enable, and then click Apply. To add all IP addresses and MAC addresses to the Static IP list, click Select All. To update the on-screen - Cisco RV042 | User Guide - Page 28
client host's IP address will be released. Click Refresh to update the on-screen information. System Management Tab > Dual-WAN There are two functions provided for users, Smart Link Backup and Load Balance. If you selected DMZ on the Setup > Network screen, you will not be able to configure the Dual - Cisco RV042 | User Guide - Page 29
enter the IP address. Click Save Settings to save your changes, or click Cancel Changes to undo them. 10/100 4-Port VPN Router Load Balance System Management > Dual-WAN > Load Balance Network Service Detection Enable Network Service Detection Network Service Detection helps manage your connection - Cisco RV042 | User Guide - Page 30
want to delete a service you have created, select it and click Delete selected service. Click Save Settings to save your changes, or click Cancel Changes to undo them. Click Exit to return to the Dual-WAN screen. 10/100 4-Port VPN Router System Management > Bandwidth Management > Rate Control 23 - Cisco RV042 | User Guide - Page 31
Service Management Service Name Enter a name. Protocol Select the protocol it uses. Port Range Enter its range. Click Add to List. Click Save Settings to save your changes, or click Cancel Changes to undo them. Click Exit to return to the Bandwidth Management screen. 10/100 4-Port VPN Router - Cisco RV042 | User Guide - Page 32
changes, or click Cancel Changes to undo them. Click Exit to return to the Bandwidth Management screen. 10/100 4-Port VPN Router If you want to modify a service you have created, select it and click Update this service. Make changes. Click Save Settings to save your changes, or click Cancel Changes - Cisco RV042 | User Guide - Page 33
the Domain Name Service (DNS), which allows users to enter an easily remembered host name, such as www.linksys.com, instead of numerical TCP/IP addresses to access Internet resources. The DNS Name Lookup tool will return the numerical TCP/IP address of a host name. 10/100 4-Port VPN Router The ping - Cisco RV042 | User Guide - Page 34
. 10/100 4-Port VPN Router Factory Default Confirmation System Management > Firmware Upgrade You can use this feature to upgrade the Router's firmware to the latest version. System Management > Firmware Upgrade Firmware Upgrade To download the firmware, refer to the Firmware Download instructions - Cisco RV042 | User Guide - Page 35
feature for all ports. System Management > Setting Backup Import Configuration File To import a configuration file, first specify where your backup preferences file is located. Click Browse, and then select the appropriate configuration file. 10/100 4-Port VPN Router Port Management > Port Setup - Cisco RV042 | User Guide - Page 36
of the feature is displayed. 10/100 4-Port VPN Router Firewall > General General Firewall The firewall is enabled by default. If you disable it, then the SPI, DoS, and Block WAN Request features, Access Rules, and Content Filters will also be disabled, and the Remote Management feature will be - Cisco RV042 | User Guide - Page 37
(port 80, the default, or 8080 is usually used). NOTE: If the Remote Management feature on the Firewall > General screen has been enabled, then users with administrative privileges can remotely access the web-based utility. Use http://, or use https:// - Cisco RV042 | User Guide - Page 38
rule, or click the Trash Can icon to delete an access rule. 10/100 4-Port VPN Router Add a New Access Rule Services Wizard If you need help to configure the access rules, click Wizard, and follow the on-screen instructions. For additional information, refer to the "Wizard" section of this chapter - Cisco RV042 | User Guide - Page 39
will include log events from the Allow access rules on the Firewall > Access Rules screen, regardless of the option, Log packets match this rule. 10/100 4-Port VPN Router Source Interface Select WAN1, WAN2, LAN, or Any. Source Select the Source IP address(es) for the access rule. If it can be any - Cisco RV042 | User Guide - Page 40
of Connected Tunnels, Phase 2 Encrypt/Auth/Group, Local Group, and Remote Client will be displayed. Click Close to exit this screen and return to the Summary screen. Tunnel Status Add New Tunnel Click Add New Tunnel to add a VPN tunnel. The Mode Choose screen appears. 10/100 4-Port VPN Router 33 - Cisco RV042 | User Guide - Page 41
Local Group. 10/100 4-Port VPN Router Remote Group The IP address and subnet mask of the Remote Group are displayed here. Remote Gateway It shows the IP address of the Remote Gateway. Tunnel Test Click Connect to verify the status of the VPN tunnel. The test result will be updated in the Status - Cisco RV042 | User Guide - Page 42
end of the tunnel. IP Only The default is IP Only. Only the device with a specific IP address will be able to access the tunnel. VPN > Gateway to Gateway 10/100 4-Port VPN Router Local Security Gateway Type > IP Only IP address The WAN (or Internet) IP address of the Router automatically appears - Cisco RV042 | User Guide - Page 43
so you do not need to enter the IP address. When the Remote Security Gateway requests to create a tunnel with the Router, the Router will work as a responder. 10/100 4-Port VPN Router Local Security Group Type > Subnet IP address Enter the IP address. The default is 192.168.1.0. Subnet Mask Enter - Cisco RV042 | User Guide - Page 44
Advanced Configuration Local Security Group Type > IP Range IP range Enter the range of IP addresses. The default is 192.168.1.0~254. Remote Group Setup Before you configure the Remote Group Setup, make sure your VPN tunnel will have two different IP subnets. For example, if the local VPN Router - Cisco RV042 | User Guide - Page 45
the remote subnet will be able to access the tunnel. 10/100 4-Port VPN Router Remote Security Group Type > Subnet IP address Enter the IP address. Subnet Mask Enter the subnet mask. The default is 255.255.255.0. IP Range Specify a range of IP addresses within a subnet that will be able to access - Cisco RV042 | User Guide - Page 46
Key periodically to maximize VPN security. 10/100 4-Port VPN Router Manual If you select Manual, you generate the key yourself, and no key negotiation is needed. Manual key management is used in small static environments or for troubleshooting purposes. Keying Mode > Manual Incoming and Outgoing - Cisco RV042 | User Guide - Page 47
use 10/100 4-Port VPN Router of portions of the original IP header in the hashing process. Select this option to use this feature. Then select MD5 or SHA1. MD5 produces a 128-bit digest to authenticate packet data. SHA produces a 160-bit digest to authenticate packet data. Both sides of the tunnel - Cisco RV042 | User Guide - Page 48
Chapter 4 Advanced Configuration VPN > Client to Gateway NOTE: The 10/100 4-Port VPN Router supports IPSec VPN client software, including the Linksys QuickVPN software. To manage access for Linksys QuickVPN clients, click the VPN Client Access tab. (For more information about QuickVPN, refer to " - Cisco RV042 | User Guide - Page 49
the local LAN user(s) behind the Router that can use this VPN tunnel. Select the type you want to use: IP, Subnet, or IP Range. Follow the instructions for the type you want to use. 10/100 4-Port VPN Router Local Security Group Type > Subnet IP address Enter the IP address. The default is 192.168 - Cisco RV042 | User Guide - Page 50
if the Dual WAN feature is enabled). Enable Check this box to enable a group VPN. Local Group Setup Local Security Group Type Select the local LAN user(s) behind the Router that can use this VPN tunnel. Select the type you want to use: IP, Subnet, or IP Range. Follow the instructions for the - Cisco RV042 | User Guide - Page 51
the range of IP addresses. The default is 192.168.1.0~254. Remote Client Setup Remote Client Select the type you want to use: Domain Name(FQDN), E-mail Addr.(USER FQDN), or Microsoft XP/2000 VPN Client. Follow the instructions for the type you want to use. 10/100 4-Port VPN Router Domain Name(FQDN - Cisco RV042 | User Guide - Page 52
160-bit digest. SHA is recommended because 10/100 4-Port VPN Router it is more secure. Both ends of the VPN tunnel must use the same Phase 2 Authentication setting. Phase 2 SA Life Time Configure the length of time a VPN tunnel is active in Phase 2. The default is 3600 seconds. Preshared Key This - Cisco RV042 | User Guide - Page 53
The VPN Client Access screen allows you to manage access for Linksys QuickVPN clients. (The Router supports up to 50 Linksys QuickVPN clients free of charge. If the Router you have only supports up to ten clients, then upgrade its firmware. Refer to "Appendix F: Firmware Upgrade" for instructions - Cisco RV042 | User Guide - Page 54
OK to continue. 10/100 4-Port VPN Router Generate Certificate Confirmation Export Certificate for Administrator The certificate for the administrator contains the private key and should be stored in a safe place as a backup. If you reset the Router to its factory defaults, then you can import - Cisco RV042 | User Guide - Page 55
software and Windows XP or 2000. VPN > PPTP Server 10/100 4-Port VPN Router PPTP Server Enable PPTP Server Select this option to allow PPTP VPN tunnels. IP Address Range Range Start Enter the starting LAN IP address of the range allotted to PPTP VPN clients. The default is 192.168.1.200. Range - Cisco RV042 | User Guide - Page 56
Enter the Syslog server name or IP address. Click Save Settings to save 10/100 4-Port VPN Router your changes, and then restart the Router for the changes to take effect. E-mail You may want logs or alert messages to be e-mailed to you. If so, then configure the E-mail settings. Enable E-Mail Alert - Cisco RV042 | User Guide - Page 57
all logins. The Firewall Log displays all activities regarding the Router's firewall. The VPN Log shows information about VPN tunnel activity. Router's ports (LAN and WAN ports). For each port, the following statistics are listed: Device Name, Status, IP Address, MAC Address, Subnet Mask, Default - Cisco RV042 | User Guide - Page 58
4 Advanced Configuration 2. To use the WAN2 (DMZ/Internet) port as a WAN (Internet) port, select Dual WAN. To use the WAN2 (DMZ/Internet) port as a DMZ port, select DMZ. Then click Next to continue. Click Exit if you want to exit the Setup Wizard. Log > System Statistics Click Refresh to update - Cisco RV042 | User Guide - Page 59
the DNS server IP addresses you want to use (you must enter at least one). Click Next to continue, and proceed to step 6. Click Previous if you want to return to the previous screen. Click Exit if you want to exit the Setup Wizard. Obtain an IP Automatically 10/100 4-Port VPN Router DNS Servers 52 - Cisco RV042 | User Guide - Page 60
DMZ port, go to step 7. 7. Complete the DMZ IP and Subnet Mask fields with the information provided by your ISP. Click Next to continue, and proceed to step 8. Click Previous if you want to return to the previous screen. Click Exit if you want to exit the Setup Wizard. DMZ 10/100 4-Port VPN Router - Cisco RV042 | User Guide - Page 61
to exit the Setup Wizard. Select the Action 4. Select the service you want from the Service pull-down menu. Click Next to continue. Click Previous if you want to return to the previous screen. Click Exit if you want to exit the Setup Wizard. Access Rules Policy 10/100 4-Port VPN Router Select the - Cisco RV042 | User Guide - Page 62
Access Rule should be in effect. Select the Source 10/100 4-Port VPN Router When It Works If you selected Always, click Next to continue. Click Previous if you want to return to the previous screen. Click Exit if you want to exit the Setup Wizard. If you selected Scheduling, click Next to continue - Cisco RV042 | User Guide - Page 63
Line Manual. The Support page of the Linksys website appears. Follow the on-screen instructions to access the Downloads page for the 10/100 4-Port VPN Router (model number: RV042). After downloading the user guide to your computer, open it using Adobe Reader. Linksys Web Site Click Linksys Web Site - Cisco RV042 | User Guide - Page 64
cable modem in order to use the Router. Connect your cable connection to the cable modem, insert the setup CD into your computer, and then follow the on‑screen instructions. WEB: If your questions are not addressed here, refer to the Linksys website, www.linksys.com. 10/100 4-Port VPN Router 57 - Cisco RV042 | User Guide - Page 65
WAN IP address of the Router> if you have enabled the HTTPS feature. 2. A login screen prompts you for your User name and Password. Enter admin in the User name field, and enter admin in the Password field. (You can change the Password on the Setup > Password screen.) Then click OK. Computer to VPN - Cisco RV042 | User Guide - Page 66
will not be installed on the computer. VPN Client Access Screen 1. On the VPN Client Access screen, enter the user name in the User Name field. 2. Enter the password in the New Password field, and enter it again in the Confirm New Password field. 10/100 4-Port VPN Router License Agreement 59 - Cisco RV042 | User Guide - Page 67
100 4-Port VPN Router Installation Complete 10. Click Finish to complete the installation. Proceed to the section, "Install the Client Certificate". Install the Client Certificate For each QuickVPN client, save the client certificate to the directory where the QuickVPN program is installed. Example - Cisco RV042 | User Guide - Page 68
Password assigned to you. •• Server Address Enter the IP address or domain name of the Linksys 10/100 4-Port VPN Router. •• Port for QuickVPN Enter the port number that the QuickVPN client will use to communicate with the remote VPN router, or keep the default, Auto. To terminate the VPN tunnel - Cisco RV042 | User Guide - Page 69
Router) •• Two VPN Routers that are both connected to the Internet Any VPN Routers can be deployed; however, this example uses the 4-Port SSL/IPSec VPN Router (model number: RVL200) and the 10/100 4-Port VPN Router (model number: RV042). Configuration when the Remote Gateway Uses a Static IP Address - Cisco RV042 | User Guide - Page 70
, click Advanced. Otherwise, click Save Settings. Configuration of PC 1 and PC 2 Verify that PC 1 and PC 2 can ping each other (refer to Windows Help for more information). If they can ping each other, then the VPN tunnel is configured correctly. RV042 VPN Settings 10/100 4-Port VPN Router 63 - Cisco RV042 | User Guide - Page 71
Subnet. Enter the RVL200's local network settings in the IP Address and Subnet Mask fields. 10/100 4-Port VPN Router RVL200 IPSec VPN Settings 8. For the Remote Security Gateway Type, select IP Only. Then select IP by DNS Resolved. Enter the RV042's domain name in the field provided. 9. For the - Cisco RV042 | User Guide - Page 72
, click Advanced Settings. Otherwise, click Save Settings. Configuration of PC 1 and PC 2 Verify that PC 1 and PC 2 can ping each other (refer to Windows Help for more information). If they can ping each other, then the VPN tunnel is configured correctly. 10/100 4-Port VPN Router RV042 Dynamic IP - Cisco RV042 | User Guide - Page 73
Configuration" for details.) 3. Click the VPN tab. 4. Click the Gateway to Gateway tab. 5. Enter a name in the Tunnel Name field. 6. Select the appropriate Interface, WAN1 or WAN2. 10/100 4-Port VPN Router 7. Select Enable. 8. For the Local Security Gateway Type, select IP Only. The WAN IP address - Cisco RV042 | User Guide - Page 74
is connected to the Internet •• Two 10/100 4-Port VPN Routers (model number: RV042), one of which is connected to the Internet 10/100 4-Port VPN Router Configuration of Scenario 1 In this scenario, Router A is the RVL200 Initiator, while Router B is the RVL200 Responder. WAN: 192.168.99.11 NAT - Cisco RV042 | User Guide - Page 75
WAN IP address of NAT 2 - RV042 in the IP Address field. 9. For the Remote Security Group Type, select Subnet. Enter Router A's local network settings in the IP Address and Subnet Mask fields. 10. In the IPSec Setup section, select the appropriate encryption, authentication, and other key management - Cisco RV042 | User Guide - Page 76
in RFC 3947. 10/100 4-Port VPN Router Setup > One-to-One NAT 6. In the Private Range Begin field, enter 99.1. 7. In the Public Range Begin field, enter 111.11. 8. In the Range Length field, enter an appropriate value. The range length cannot exceed the number of valid IP addresses. To map a single - Cisco RV042 | User Guide - Page 77
fields. Router B's IPSec VPN Settings 10/100 4-Port VPN Router Router A's IPSec VPN Settings NOTE: This configuration is the same as the configuration of Router A in scenario 1. 8. For the Remote Security Gateway Type, select IP Only. Enter Router B's WAN IP address in the IP Address field. 70 - Cisco RV042 | User Guide - Page 78
encryption, authentication, and other key management settings. 11. In the Preshared Key field, enter a string for this key, for example, 13572468. 12. If you need more detailed settings, click Advanced Settings. Otherwise, click Save Settings. IPSec NAT Traversal 10/100 4-Port VPN Router 71 - Cisco RV042 | User Guide - Page 79
. Enter a name, such as Vonage 2, in the Service Name field. QoS > Bandwidth Management 5. On the Service Management screen, enter a name, such as Vonage VoIP, in the Service Name field. 4-Port SSL/IPSec VPN Router Add Vonage 2 Service 10. From the Protocol drop-down menu, select UDP. 11. Enter - Cisco RV042 | User Guide - Page 80
bandwidth. For example, you can set a maximum rate of 80 kbit/sec. 4-Port SSL/IPSec VPN Router 13. Select Enable to enable this rule. 14. After you have set up the rule, click Add to list. 15. Set up a rule for Vonage 2. Select Vonage 2 from the Service drop-down menu. 16. Enter the IP address - Cisco RV042 | User Guide - Page 81
, click Firmware Download from Linksys Web Site. System Management > Firmware Upgrade 4. The Support page of the Linksys website appears. Follow the on-screen instructions to access the Downloads page for the 10/100 4-Port VPN Router (model number: RV042). 5. Download the firmware upgrade file - Cisco RV042 | User Guide - Page 82
-click the .exe file. 9. In the Router IP field, enter the IP address of the Router. Firmware Upgrade Utility Login 10. In the Password field, enter the password for access to the Router. 11. Click Next, and then follow the on-screen instructions. Firmware Upgrade 10/100 4-Port VPN Router 75 - Cisco RV042 | User Guide - Page 83
IP address of the Router> if you have enabled the HTTPS feature. 2. A login screen prompts you for your User name and Password. Enter admin in the User name field, and enter admin in the Password field. (You can change the Password on the Setup > Password screen.) Then click OK. Login Screen 10/100 - Cisco RV042 | User Guide - Page 84
supports this service, click I have my Activation Code (AC) and want to activate ProtectLink Gateway. Then use your current activation code to transfer your license for the ProtectLink service to the new router. How to Use the Service Configure the service to protect your network. 10/100 4-Port VPN - Cisco RV042 | User Guide - Page 85
the number of attempted visits to a restricted URL. To reset the counter to zero, click Reset Counter. For each URL category, select the appropriate Filtering option. If you want to filter a sub-category, click + to view 10/100 4-Port VPN Router the sub-categories for each category. Then select the - Cisco RV042 | User Guide - Page 86
To have your e-mail checked, you will need to provide the domain name and IP address of your e-mail server. If you do not know this information, contact your ISP. 10/100 4-Port VPN Router ProtectLink > License License Update Information To refresh the license information displayed on-screen, click - Cisco RV042 | User Guide - Page 87
expires are displayed. Renew To renew your license, click Renew. Then follow the on-screen instructions. Add Seats Each seat allows an e-mail account to use Email Protection. To add seats to your license, click Add Seats. Then follow the on-screen instructions. 10/100 4-Port VPN Router 80 - Cisco RV042 | User Guide - Page 88
Throughput IPSec Throughput Security Firewall Access Rules Port Forwarding Port Triggering URL Filtering Network Dual WANs Protocol Binding DHCP DNS NAT DMZ Routing QoS Port-based QoS Service based QoS RV042 IEEE 802.3, 802.3u 4 10/100 RJ-45 Ports, 1 10/100 RJ-45 Internet Port, 1 10/100 RJ-45 DMZ - Cisco RV042 | User Guide - Page 89
, Linksys does not warrant that the product, software or any equipment, system or network on which the product or software is used will be free of vulnerability to intrusion or attack. The product may include or be bundled with third party software or 10/100 4-Port VPN Router service offerings - Cisco RV042 | User Guide - Page 90
for support services) can be found at: www.linksys.com/support. This limited warranty is governed by the laws of the jurisdiction in which the Product was purchased by you. Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623. Warranty Information 10/100 4-Port VPN Router - Cisco RV042 | User Guide - Page 91
. 10/100 4-Port VPN Router Schedule 1 Linksys Software License Agreement THIS LICENSE AGREEMENT IS BETWEEN YOU AND CISCO-LINKSYS LLC OR ONE OF ITS AFFILIATES CISCO SYSTEMS-LINKSYS (ASIA) PTE LTD. OR CISCO-LINKSYS K.K. ("LINKSYS") LICENSING THE SOFTWARE INSTEAD OF CISCO-LINKSYS LLC. BY DOWNLOADING - Cisco RV042 | User Guide - Page 92
this Agreement. Limited Warranty. The warranty terms and period specified in the applicable Linksys Product User Guide shall also apply to the Software. 10/100 4-Port VPN Router Disclaimer of Liabilities. IN NO EVENT WILL LINKSYS OR ITS SUPPLIERS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR - Cisco RV042 | User Guide - Page 93
document free for all its users. This General Public License to freedom, not price. Our General Public Licenses charge for this service if you wish you modify it. For example, if you distribute copies original, so that any problems introduced by others will not 10/100 4-Port VPN Router TERMS addressed - Cisco RV042 | User Guide - Page 94
that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License for noncommercial distribution and only if you received the program 10/100 4-Port VPN Router in object code or executable form with such an offer, - Cisco RV042 | User Guide - Page 95
all. For example, if a in detail to address new problems or concerns. Each 10/100 4-Port VPN Router may choose any version ever published by the Free Software Foundation. 10 decision will be guided by the two ALL NECESSARY SERVICING, REPAIR OR Schedule 3 If this Linksys product contains open source - Cisco RV042 | User Guide - Page 96
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR 10/100 4-Port VPN Router OTHERWISE) ARISING IN ANY WAY OUT OF - Cisco RV042 | User Guide - Page 97
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY the GNU Public License.] END OF SCHEDULE 3 Software License Agreement 10/100 4-Port VPN Router 90 - Cisco RV042 | User Guide - Page 98
and used according to the instructions, may cause harmful interference turning the equipment off and on, the user is encouraged to try to correct the line cord. •• Do not use this product near water, for example, in a wet basement or near a swimming pool. •• Avoid 10/100 4-Port VPN Router 91 - Cisco RV042 | User Guide - Page 99
EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) This document contains important information for users with regards to the proper disposal and recycling of Linksys contact your local authorities, waste disposal service, or the shop where you 10/100 4-Port VPN Router 92 - Cisco RV042 | User Guide - Page 100
2002/96/EC Français (French) - Informations environnementales pour les clients de l'Union européenne La directive européenne 2002/96/CE veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l'endroit où vous izstrādājumu. 10/100 4-Port VPN Router 93 - Cisco RV042 | User Guide - Page 101
waar u het product hebt aangeschaft. Norsk (Norwegian) - Miljøinformasjon for kunder i EU EU-direktiv 2002/96/EF krever at utstyr med følgende symbol avbildet på produktet og/eller do lokalnych władz, służb oczyszczania miasta lub sklepu, w którym produkt został nabyty. 10/100 4-Port VPN Router 94 - Cisco RV042 | User Guide - Page 102
Português (Portuguese) - Informação ambiental para clientes da União Europeia A Directiva Europeia 2002 . Suomi (Finnish) - Ympäristöä koskevia tietoja EUalueen asiakkaille EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä symboli visit www.linksys.com 10/100 4-Port VPN Router 95 - Cisco RV042 | User Guide - Page 103
FTP Site ftp.linksys.com Advice Line 800-546-5797 (LINKSYS) Support 800-326-7114 RMA (Return Merchandise Authorization) http://www.linksys.com/warranty NOTE: Details on warranty and RMA issues can be found in the Warranty section of this Guide. Contact Information 10/100 4-Port VPN Router
USER GUIDE
BUSINESS SERIES
10/100 4-Port
VPN Router
Model:
RV042