Cisco SD208T-NA User Guide

Cisco SD208T-NA Manual

Get Cisco SD208T-NA PDF manuals and user guides View all Cisco SD208T-NA manuals
Add to My Manuals
Save this manual to your list of manuals

Cisco SD208T-NA manual content summary:

  • Cisco SD208T-NA | User Guide - Page 1
    10/100 Switches Use this guide to install the following products: 5-Port 10/100 Switch 8-Port 10/100 Switch 16-Port 10/100 Switch SD205 SD208 SD216 User Guide
  • Cisco SD208T-NA | User Guide - Page 2
    Linksys at its option to repair or replace the product or refund Your purchase price less any rebates. If the product proves defective during the Warranty Period call Linksys Technical Support inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623. FCC STATEMENT Every 10/100 Switch has been tested
  • Cisco SD208T-NA | User Guide - Page 3
    B: Specifications 9 Environmental 10 Appendix C: Warranty Information 11 Appendix D: Contact Information 12 Chapter 1: Introduction r The 10/100 Switch This newly redesigned Linksys 5-, 8-, or 16-Port 10/100 Switch can significantly increase your network traffic's speed. A switch serves
  • Cisco SD208T-NA | User Guide - Page 4
    Getting to Know the 10/100 Switch OPlvaenrnviinegwYour Network Layout The 5-, 8-, and 16-Port 10/100 Switches differ in number of LEDs and ports. Pictured here is the 5-Port 10/100 Switch; however, the other Switches are similar in form. Front Panel LEDs Figure 2-3 The power port is located on the
  • Cisco SD208T-NA | User Guide - Page 5
    feet). 4 Connecting Network Devices Follow these instructions for the 5-, 8-, and 16-Port 10/100 Switches (the 5-Port 10/100 Switch is shown in Figures 3-2 and 3-3). 1. Make sure all the devices you will connect to the Switch are powered off. 2. Connect a Category 5 Ethernet network cable to one
  • Cisco SD208T-NA | User Guide - Page 6
    10/100 Switch is complete. Figure 3-4 6 Appendix A: Glossary 10BaseT - An Ethernet standard that uses twisted wire pairs. 100BaseTX - IEEE physical layer specification for 100 Mbps over two pairs of Category 5 UTP or STP wire. Auto MDI/MDI-X - On a network hub or switch, an auto MDI/MDI-X port
  • Cisco SD208T-NA | User Guide - Page 7
    B: Specifications Model Number Standards Ports SD205 SD208 SD216 Cabling Type LEDs SD205 SD208 SD216 SD205 5-Port 10/100 Switch SD208 8-Port 10/100 Switch SD216 16-Port 10/100 Switch IEEE 802.3, IEEE 802.3u 5 RJ-45 10/100 8 RJ-45 10/100 16 RJ-45 10/100 Category 5 Ethernet System, Port Status
  • Cisco SD208T-NA | User Guide - Page 8
    90%, Non-Condensing 10 Appendix C: Warranty Information BE SURE TO HAVE YOUR PROOF OF PURCHASE AND A BARCODE FROM THE PRODUCT'S PACKAGING ON HAND WHEN CALLING. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. IN NO EVENT SHALL LINKSYS'S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT
  • Cisco SD208T-NA | User Guide - Page 9
    D: Contact Information For help with the installation or operation of this 10/100 Switch, contact Linksys Technical Support at one of the phone numbers or Internet addresses below. Sales Information Technical Support RMA (Return Merchandise Authorization) Issues Fax E-mail Web FTP Site 800
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
Use this guide to install the following products:
5-Port 10/100 Switch
SD205
8-Port 10/100 Switch
SD208
16-Port 10/100 Switch
SD216
User Guide
10/100 Switches