Cisco SRW208L User Guide

Cisco SRW208L - Small Business Managed Switch Manual

Get Cisco SRW208L - Small Business Managed Switch PDF manuals and user guides
UPC - 745883571062
View all Cisco SRW208L manuals
Add to My Manuals
Save this manual to your list of manuals

Cisco SRW208L manual content summary:

  • Cisco SRW208L | User Guide - Page 1
    USER GUIDE 8-Port 10/100 Ethernet Switch with Webview Model: SRW208/SRW208G/SRW208L/SRW208P/SRW208MP BUSINESS SERIES
  • Cisco SRW208L | User Guide - Page 2
    Systems, Inc. and/ or its affiliates in the U.S. and certain other countries. Copyright © 2007 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. 8-Port 10/100 Ethernet Switch with Webview About This Guide
  • Cisco SRW208L | User Guide - Page 3
    Device Information 18 System Information 19 PoE Information 19 Setup > Network Settings 19 Identification 19 IP Configuration 19 Setup > Time 20 Set Time 20 Local Time 20 Daylight Saving 20 SNTP Servers 20 Port Management > Port Settings 20 8-Port 10/100 Ethernet Switch with Webview ii
  • Cisco SRW208L | User Guide - Page 4
    35 Security > Multiple Hosts 36 Security > Storm Control 37 QoS 37 QoS > CoS Settings 37 CoS Default 38 QoS > Queue Settings 38 QoS > DSCP Settings 38 QoS > Bandwidth 38 QoS > Basic Mode 39 QoS > Advanced Mode 39 Out of Profile DSCP 40 8-Port 10/100 Ethernet Switch with Webview iii
  • Cisco SRW208L | User Guide - Page 5
    Mirroring 54 Admin > Cable Test 54 Admin > Save Configuration 55 Via TFTP 55 Via HTTP 55 Backup 55 Admin > Firmware Upgrade 55 Admin > Reboot 56 Admin > Factory Defaults 56 Admin > Server Logs 56 Admin > Memory Logs 57 Admin > Flash Logs 57 8-Port 10/100 Ethernet Switch with Webview iv
  • Cisco SRW208L | User Guide - Page 6
    75 Safety Notices 75 Industry Canada Statement 75 Avis d' Industrie Canada 75 User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE 76 Appendix G: Contact Information 80 8-Port 10/100 Ethernet Switch with Webview v
  • Cisco SRW208L | User Guide - Page 7
    network. The SRW208P and SRW208MP support Automatic Load Sensing - Power control circuitry automatically detects Power over Ethernet on access point before providing power. Power feeding of Ethernet limited for fixed 10/100 Base-T/TX ports. The SRW208MP can provide maximum output power per PoE port
  • Cisco SRW208L | User Guide - Page 8
    Console Interface for Configuration for more information. SRW208G - Front Panel The LEDs and ports are located on the front panel of the Switch. 8-Port 10/100 Ethernet Switch with Webview Product Overview Front Panel SYSTEM (Green) The system LED lights up to indicate that the Switch is powered
  • Cisco SRW208L | User Guide - Page 9
    an attached device. It flashes to indicate that the Switch is actively sending or receiving data over that port. PoE (Orange) The PoE LED lights up to indicate a device is connected utilizing Power over Ethernet on the corresponding port (1 through 8). 8-Port 10/100 Ethernet Switch with Webview 3
  • Cisco SRW208L | User Guide - Page 10
    to Chapter 4: Using the Console Interface for Configuration for more information. Back Panel The console and power ports are located on the back panel of the Switch. Back Panel POWER The Power port is where you will connect the AC power. 8-Port 10/100 Ethernet Switch with Webview Product Overview
  • Cisco SRW208L | User Guide - Page 11
    mentioned in "Appendix D: Specifications" as you are placing the Switch. 4. Connect the Switch to network devices according to the Hardware Installation instructions below. Wireless Desktop Notebook Access Point Typical Network Configuration When you connect your network devices, make sure you
  • Cisco SRW208L | User Guide - Page 12
    could damage the Switch and would invalidate your warranty. 3. Make sure the brackets are properly attached to the Switch. 4. Use the appropriate screws (not included) to securely attach the brackets to your rack. Mounting in Rack Attaching the Brackets 8-Port 10/100 Ethernet Switch with Webview
  • Cisco SRW208L | User Guide - Page 13
    Proper Wall-Mount Orientation (Horizontal) NOTE: Linksys is not responsible for damages incurred by insecure wall-mounting hardware. 1. Determine where you want to mount the Switch. Ensure that the wall you use is smooth, flat, dry and 8-Port 10/100 Ethernet Switch with Webview Incorrect Wall-Mount
  • Cisco SRW208L | User Guide - Page 14
    light up on the Switch. If a port has an active Gigabit connection, then its corresponding Gigabit LED will also light up. NOTE: If you need to reset the Switch, unplug the power cord from the back of the Switch. Wait a few seconds and then reconnect it. 8-Port 10/100 Ethernet Switch with Webview
  • Cisco SRW208L | User Guide - Page 15
    per Second: 38400 Databits: 8 Parity: None Stop bits: 1 Flow control: None HyperTerminal Connection Description Screen 8-Port 10/100 Ethernet Switch with Webview HyperTerminal Properties Screen Connecting to the Switch through a Telnet Session 1. Open a command line editor and enter telnet 192.168
  • Cisco SRW208L | User Guide - Page 16
    Configuration 6. File Management 7. Restore System Default Settings 8. Reboot System 0. Back to Main Menu. System Information From the System Information screen you can check current firmware versions and other general switch information. Main Menu 8-Port 10/100 Ethernet Switch with Webview System
  • Cisco SRW208L | User Guide - Page 17
    key to save your changes. To exit, select Quit and press the Enter key. General Information 8-Port 10/100 Ethernet Switch with Webview Serial Port Configuration Telnet Configuration On the Telnet Configuration screen, the time-out is displayed. The value is entered in seconds. If you do not want
  • Cisco SRW208L | User Guide - Page 18
    Configuration Using the Console Interface Telnet Configuration SSH Configuration On the SSH Configuration screen, you can select SSH Server Configuration, SSH Server Status, SSH Crypto Key Generation, and SSH Keys Fingerprints. SSH Server Configuration 8-Port 10/100 Ethernet Switch with Webview 12
  • Cisco SRW208L | User Guide - Page 19
    Chapter 4 Configuration Using the Console Interface SSH Crypto Key Generation SSH Keys Fingerprints On the SSH country name. (Range: 2 - 2) Validity Term Specifies number of days certification is valid. (Range: 30 - 3650) User & Password Settings 8-Port 10/100 Ethernet Switch with Webview 13
  • Cisco SRW208L | User Guide - Page 20
    to the Action menu. Select Save and press the Enter key to save your changes. To exit, select Quit and press the Enter key. IP Configuration 8-Port 10/100 Ethernet Switch with Webview 14
  • Cisco SRW208L | User Guide - Page 21
    the IP address of the address whose route you want to trace. HTTPS Nework Configuration The Network Configuration screen offers a choice of two tests, Ping and TraceRoute. Network Configuration 8-Port 10/100 Ethernet Switch with Webview Select Edit to change the IP address, and select Execute to
  • Cisco SRW208L | User Guide - Page 22
    Enter key. You will be asked if you want to continue. Press the y key to restore the Switch's default settings, or press the n key to cancel. Restore Default 8-Port 10/100 Ethernet Switch with Webview Reboot System Back to Main Menu Select Back to Main Menu if you want to return to the main menu
  • Cisco SRW208L | User Guide - Page 23
    Chapter 4 Configuration Using the Console Interface The Port Configuration screen displays the port numbers, their status, auto-negotiation status, speed and duplex mode, screen explains how to navigate the various screens of the console interface. 8-Port 10/100 Ethernet Switch with Webview 17
  • Cisco SRW208L | User Guide - Page 24
    Management, VLAN Management, Statistics, ACL, Security, QoS (Quality of Service), Spanning Tree, Multicast, SNMP, Admin, and Logout. Click one of the main tabs to view additional tabs. Login Screen 8-Port 10/100 Ethernet Switch with Webview NOTE: The LEDs displayed in the web-based utility are not
  • Cisco SRW208L | User Guide - Page 25
    amount of power the device can supply. System Operation Status Indicates whether the PoE function is on or off. Mainpower Consumption Displays how much power is currently used. 8-Port 10/100 Ethernet Switch with Webview Setup > Network Settings Setup > Network Settings The Network Settings screen
  • Cisco SRW208L | User Guide - Page 26
    to configure the time settings for the Switch. Setup > Time Set Time Use System Time Port 10/100 Ethernet Switch with Webview Daylight Saving Daylight Saving Select Daylight Saving to enable it on the Switch. If the Switch should use US daylight savings, then select USA. If the Switch should use EU
  • Cisco SRW208L | User Guide - Page 27
    or LAGs. Detail The Detail button will open the Port Configuration Detail screen. 8-Port 10/100 Ethernet Switch with Webview Port Management > Port Configuration Port The number of the port. Description Displays a brief description of the port (can be entered by clicking on the Detail button
  • Cisco SRW208L | User Guide - Page 28
    SRW208. Click the Save Settings button to save your changes. 8-Port 10/100 Ethernet Switch with Webview Port Management > Link Aggregation Port Management > Link Aggregation LAG This indicates if the port . Speed The connection speed is displayed here. Duplex The connection duplex is displayed
  • Cisco SRW208L | User Guide - Page 29
    default. Admin Key A channel will only be formed between ports having the same admin key. This only applies to ports located on the same switch. Port Management > PoE Power Settings 8-Port 10/100 Ethernet Switch with Webview Port Management > PoE Power Settings Port Displays the selected port
  • Cisco SRW208L | User Guide - Page 30
    , press the Add button. VLAN Name Displays the user-defined VLAN name. VLAN Range VLAN Range. Indicates a range of VLANs being configured. To add the defined range of VLAN ID numbers, press the Add Range button. 8-Port 10/100 Ethernet Switch with Webview VLAN Table The VLAN Table displays a list
  • Cisco SRW208L | User Guide - Page 31
    belongs to VLANs, and each VLAN is user-defined as tagged or untagged (full 802.1Q mode). 8-Port 10/100 Ethernet Switch with Webview VLAN Management > VLAN to Ports The VLAN to Ports screen contains fields for configuring VLANs to a ports. Interface Displays the interface number. Mode Indicates
  • Cisco SRW208L | User Guide - Page 32
    the configured GVRP System LAG information displays the same field information as the ports Port 10/100 Ethernet Switch with Webview Statistics > RMON Statistics Interface Indicates the device for which statistics are displayed. The possible field values are: •• Port Defines the specific port
  • Cisco SRW208L | User Guide - Page 33
    -byte frames received on the interface since the device was last refreshed. Clear Counters button This option will reset all of the statistic counts. 8-Port 10/100 Ethernet Switch with Webview Refresh Now button Use this option to refresh the statistics. Statistics > RMON History The RMON History
  • Cisco SRW208L | User Guide - Page 34
    since the device was last refreshed. 8-Port 10/100 Ethernet Switch with Webview CRC Align Errors Displays the network alarms. Network alarms occur when a network problem, or event, is detected. Rising and falling thresholds generate events. Statistics > RMON Alarms Alarm Entry Indicates a specific
  • Cisco SRW208L | User Guide - Page 35
    device or in the management system. If the device is not reset, the entry remains in the Log Table. •• TRAP Indicates that an SNMP trap is generated, and alarm interval time in seconds. 8-Port 10/100 Ethernet Switch with Webview Owner Displays the device or user that defined the alarm. The Add
  • Cisco SRW208L | User Guide - Page 36
    an excessive amount of network traffic. Refresh Rate Indicates the amount of time that passes before the port utilization statistics are refreshed. The possible field values are: •• No Refresh Indicates that the statistics are not refreshed. 8-Port 10/100 Ethernet Switch with Webview Statistics
  • Cisco SRW208L | User Guide - Page 37
    Configuration Port 10/100 Ethernet Switch button resets all user-defined IP based ACL. Delete ACL Deletes the selected ACL. Action Indicates the action assigned to the packet matching the ACL. Packets are forwarded or dropped. In addition, the port can be shut down, a trap can be sent to the network
  • Cisco SRW208L | User Guide - Page 38
    . Psh Indicates the packet is pushed. Rst Indicates the connection is dropped. Syn Indicates request to start a session. Fin Indicates request to close a session. 8-Port 10/100 Ethernet Switch with Webview Source Port Defines the TCP/UDP source port to which the ACE is matched. This field is
  • Cisco SRW208L | User Guide - Page 39
    ACL is assigned on a port or LAG, flows from that ingress interface that do not match the ACL are matched to the default rule, which is Drop unmatched ACL Binding configuration to the ACL Binding Table at the bottom of the screen. Security > RADIUS 8-Port 10/100 Ethernet Switch with Webview Security >
  • Cisco SRW208L | User Guide - Page 40
    network integrity through encrypted 8-Port 10/100 Ethernet Switch with Webview protocol exchanges between the device and TACACS+ server. Security > TACACS+ Host IP Address Displays the TACACS+ Server IP address. Priority Displays the order in which the TACACS+ servers are used. The default
  • Cisco SRW208L | User Guide - Page 41
    Timer The Setting Timer button opens the Setting Timer screen to configure ports for 802.1x functionality. Setting Timer 802.1x Settings > Setting Timer Port Indicates the port name. 8-Port 10/100 Ethernet Switch with Webview Reauthentication Period Specifies the number of seconds in which
  • Cisco SRW208L | User Guide - Page 42
    port. 8-Port 10/100 Ethernet Switch with Webview Trap Frequency The amount of time (in seconds) between traps. The default value is 10 seconds. Security > Multiple Hosts The Multiple Hosts screen allows network managers to configure advanced port-based authentication settings for specific ports
  • Cisco SRW208L | User Guide - Page 43
    specified criteria, and that specific traffic receives preferential treatment. QoS in the network optimizes network performance and entails two basic facilities: Classifying incoming traffic into handling classes, based on an attribute, including: 8-Port 10/100 Ethernet Switch with Webview •• The
  • Cisco SRW208L | User Guide - Page 44
    which the queue settings are displayed. The possible field range is 1 - 4. WRR Weight Displays the WRR weights to queues. 8-Port 10/100 Ethernet Switch with Webview QoS > Bandwidth The Bandwidth screen allows network managers to define the bandwidth settings for a specified egress interface. 38
  • Cisco SRW208L | User Guide - Page 45
    configured on FE ports. The Add to List button adds the Bandwidth configuration to the Bandwidth Table at the bottom of the screen. QoS > Basic Mode QoS > Basic Mode 8-Port 10/100 Ethernet Switch specific queue, services such as configuring output queues for the scheduling scheme, or configuring
  • Cisco SRW208L | User Guide - Page 46
    The New Class Map button opens the New Class Map screen. 8-Port 10/100 Ethernet Switch with Webview Advanced Mode > New Class Map Class Map Name Defines maps. Single Configures the class to use manually configured information rates and exceed actions. Aggregate Policer User-defined aggregate
  • Cisco SRW208L | User Guide - Page 47
    network topologies that provide faster convergence of the spanning tree, without creating forwarding loops. 8-Port 10/100 Ethernet Switch indicates the amount of time in seconds a bridge waits before sending configuration messages. The default max age is 20 seconds. The range is 6 to 40 seconds
  • Cisco SRW208L | User Guide - Page 48
    Port 10/100 Ethernet Switch with Webview •• Filtering Filters BPDU packets when spanning tree is disabled on an interface. This is the default in seconds a root bridge waits between configuration messages. The default is 2 seconds. The range is 1 to 10 seconds. Max Age Specifies the device Maximum
  • Cisco SRW208L | User Guide - Page 49
    MAC addresses. •• Learning Indicates that the port is in Learning mode. The port cannot forward traffic, however it can learn new MAC addresses. 8-Port 10/100 Ethernet Switch with Webview •• Forwarding Indicates that the port is in Forwarding mode. The port can forward traffic and learn new MAC
  • Cisco SRW208L | User Guide - Page 50
    , the originating PPP sends Network Control Protocols (NCP) packets to select and configure one or more network layer protocols. When each of the chosen network 8-Port 10/100 Ethernet Switch with Webview layer protocols has been configured, packets from each network layer protocol can be sent over
  • Cisco SRW208L | User Guide - Page 51
    port. A Master port provides connectivity from a MSTP region to the outlying CIST root. •• Internal Indicates the port is an internal port. Role Indicates the port role assigned by the STP algorithm in order to provide to STP paths.The possible field values are: 8-Port 10/100 Ethernet Switch
  • Cisco SRW208L | User Guide - Page 52
    amount of time host waits to receive a message before timing out. The default time is 260 seconds. MRouter Timeout Indicates the amount of the time the Multicast router waits to receive a message before it times out. The default value is 300 seconds. 8-Port 10/100 Ethernet Switch with Webview 46
  • Cisco SRW208L | User Guide - Page 53
    . LAG Displays LAG that can be added to a Multicast service. The configuration options are as follows: •• Static Indicates the port is user-defined. 8-Port 10/100 Ethernet Switch with Webview Multicast > Multicast Forward All The Bridge Multicast Forward All screen contains fields for attaching
  • Cisco SRW208L | User Guide - Page 54
    in the Select from List field to be entered. View Type Indicates if the defined OID branch will be included or excluded in the selected SNMP view. The Add to List button adds the Views configuration to the Views Table at the bottom of the screen. 8-Port 10/100 Ethernet Switch with Webview 48
  • Cisco SRW208L | User Guide - Page 55
    can be made to the assigned SNMP view. 8-Port 10/100 Ethernet Switch with Webview SNMP > Group Membership The Group Membership screen provides information for assigning SNMP access control privileges to SNMP groups. User name Provides a user-defined local user list. Engine ID Indicates either the
  • Cisco SRW208L | User Guide - Page 56
    can be made to the device configuration, but not to the community. •• SNMP Admin User has access to all device configuration options, as well as permissions to Defines the password used to authenticate the management station to the device. 8-Port 10/100 Ethernet Switch with Webview SNMP > Table
  • Cisco SRW208L | User Guide - Page 57
    Port 10/100 Ethernet Switch with Webview The Add to List button adds the Notification Filter configuration to the Notification Filter Table at the bottom of the screen. SNMP are sent to specific users, and the trap type sent. SNMP notification filters provide the following services: •• Identifying
  • Cisco SRW208L | User Guide - Page 58
    Assigns no authentication method to the authentication profile. User Name Displays the user name. 8-Port 10/100 Ethernet Switch with Webview Admin > Static Address A static address can be assigned to a specific interface on this switch. Static addresses are bound to the assigned interface and
  • Cisco SRW208L | User Guide - Page 59
    default value is 300 seconds. Clear Table If checked, clears the MAC address table. Query Port Specifies the interface for which the table is queried. There are two interface types from which to select. •• Port The specific port number. •• LAG The specific MAC 8-Port 10/100 Ethernet Switch with
  • Cisco SRW208L | User Guide - Page 60
    performance monitoring. Network administrators configure port mirroring by selecting a specific port to copy all packets, and different ports from which the packets are copied. 8-Port 10/100 Ethernet Switch with Webview Admin > Cable Test Port This is the port to which the cable is connected. Test
  • Cisco SRW208L | User Guide - Page 61
    •• Destination File Specifies the name of the configuration file. The default is StartupCfg.cfg. 8-Port 10/100 Ethernet Switch with Webview Admin > FIrmware Upgrade The Firmware Upgrade screen contains the following fields: via TFTP Defines the upgrade through a TFTP Server. via HTTP Allows you
  • Cisco SRW208L | User Guide - Page 62
    is rebooted. Admin > Factory Defaults The Factory Reset screen allows network managers to reset the device to the factory defaults shipped with the switch. Restoring factory defaults results in erasing the configuration file. Admin > Factory Defaults 8-Port 10/100 Ethernet Switch with Webview Admin
  • Cisco SRW208L | User Guide - Page 63
    Chapter 5 Advanced Configuration Admin > Memory Logs The Memory Log screen contains all system logs in a chronological order that are saved in RAM (Cache). Log Index of the log message. The Message Log is available after reboot. Admin > Flash Logs 8-Port 10/100 Ethernet Switch with Webview 57
  • Cisco SRW208L | User Guide - Page 64
    Linksys Gigabit Switches. The MGBSX1 and the MGBLH1 require fiber cabling with LC connectors, and the MGBT1 requires a Category 5e Ethernet cable with an RJ-45 connector. For Fast Ethernet, you must use the MFEFX1 (100BASE-FX) or MFELX1 (100BASE-LX) SFP transceivers. 8-Port 10/100 Ethernet Switch
  • Cisco SRW208L | User Guide - Page 65
    cable from the COM port on your computer to the Console port on the Switch. 3. Power on your computer and launch HyperTerminal, follow the instructions in Chapter 4: Configuration Using the Console Interface to configure HyperTerminal to connect to the Switch. 4. Power on the Switch and watch for
  • Cisco SRW208L | User Guide - Page 66
    Appendix B 9. Press Send and the software is downloaded. Download After the software has been downloaded, the device will reboot automatically. Downloading Using Xmodem 8-Port 10/100 Ethernet Switch with Webview 60
  • Cisco SRW208L | User Guide - Page 67
    a message. Bandwidth The transmission capacity of a given device or network. Bandwidth Assignments Indicates the amount of bandwidth assigned to a specific application, user, and/or interface. 8-Port 10/100 Ethernet Switch with Webview Baud Indicates the number of signaling elements transmitted
  • Cisco SRW208L | User Guide - Page 68
    used to transfer files over a TCP/IP network. 8-Port 10/100 Ethernet Switch with Webview Full Duplex The ability of a networking device to receive and transmit data simultaneously. GARP (General Attributes Registration Protocol) Registers client stations into a multicast domain. Gateway A device
  • Cisco SRW208L | User Guide - Page 69
    types, and source and destination addresses. 8-Port 10/100 Ethernet Switch with Webview RADIUS (Remote Authentication Dial-In User Service) A protocol that uses an authentication server to control network access. RJ-45 (Registered Jack-45) An Ethernet connector that holds up to eight wires
  • Cisco SRW208L | User Guide - Page 70
    User Data Protocol) Communication protocol that transmits packets but does not guarantee their delivery. Upgrade To replace existing software or firmware with a newer version. Upload To transmit a file over a network two bits are ignored. 8-Port 10/100 Ethernet Switch with Webview Glossary 64
  • Cisco SRW208L | User Guide - Page 71
    , RFC 2618 RADIUS Client MIB, RFC 1215 Traps Embedded Remote Monitoring (RMON) Software Agent Supports four RMON Groups (History, Statistics, Alarms, and Events) for Enhanced Traffic Management, Monitoring, and 8-Port 10/100 Ethernet Switch with Webview Analysis. Firmware Upgrade Web Browser
  • Cisco SRW208L | User Guide - Page 72
    Specifications are subject to change without notice. 8-Port 10/100 Ethernet Switch with Webview Model Ports Cabling Type LEDs Performance Switching Capacity Forwarding Rate Layer 2 MAC table size Number of VLANs VLAN HOL Blocking Management Web User Interface SNMP SNMP MIBs RMON SRW208G
  • Cisco SRW208L | User Guide - Page 73
    IGMP (v1/v2) Snooping Provides for Fast Client Joins 8-Port 10/100 Ethernet Switch with Webview Streams Intensive QoS Priority levels Scheduling Class of Service Rate Limiting Standards Environmental Dimensions Unit Weight Power Certification Operating Temp. Storage Temp. Operating Humidity
  • Cisco SRW208L | User Guide - Page 74
    ), RFC2819 RMON MIB (groups 1,2,3,9 only), RFC2737 Entity MIB, RFC 2618 RADIUS Client MIB, RFC 1215 Traps Embedded Remote Monitoring (RMON) Software Agent Supports four RMON Groups (History, Statistics, Alarms, and 8-Port 10/100 Ethernet Switch with Webview Firmware Upgrade Port Mirroring Other
  • Cisco SRW208L | User Guide - Page 75
    Specifications are subject to change without notice. 8-Port 10/100 Ethernet Switch with Webview Model Ports Cabling Type LEDs Performance Switching Capacity Forwarding Rate Layer 2 MAC table size Number of VLANs VLAN HOL Blocking Management Web User Interface SNMP SNMP MIBs RMON SRW208MP
  • Cisco SRW208L | User Guide - Page 76
    IGMP (v1/v2) Snooping Provides for Fast Client Joins and Leaves of Multicast 8-Port 10/100 Ethernet Switch with Webview Intensive QoS Priority levels Scheduling Class of Service Rate Limiting Standards Environmental Dimensions Unit Weight Power Certification Operating Temp. Storage Temp. Operating
  • Cisco SRW208L | User Guide - Page 77
    Entity MIB, RFC 2618 RADIUS Client MIB, RFC 1215 Traps Private POE MIB Embedded Remote Monitoring (RMON) Software Agent Supports four RMON Groups (History, Statistics, Alarms, and Events) for Enhanced Traffic 8-Port 10/100 Ethernet Switch with Webview Firmware Upgrade Port Mirroring Other
  • Cisco SRW208L | User Guide - Page 78
    kg) External AC Power Adapter FCC Part15 Class A, CE Class A, UL, cUL, CE Mark, CB 32 to 104ºF (0 to 40ºC) -4 to 158ºF (-20 to 70ºC) 10 to 90% Noncondensing 10 to 95% Noncondensing Specifications are subject to change without notice. 8-Port 10/100 Ethernet Switch with Webview Specifications 72
  • Cisco SRW208L | User Guide - Page 79
    , software or any equipment, system or network on which the product or software is used will be free of vulnerability to intrusion or attack. The product may include or be bundled with third party software or 8-Port 10/100 Ethernet Switch with Webview service offerings. This limited warranty shall
  • Cisco SRW208L | User Guide - Page 80
    support services) can be found at: www.linksys.com/support. This limited warranty is governed by the laws of the jurisdiction in which the Product was purchased by you. Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623. Warranty Information 8-Port 10/100 Ethernet Switch
  • Cisco SRW208L | User Guide - Page 81
    complies with the specifications for a Class with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user Port 10/100 Ethernet Switch with Webview 75
  • Cisco SRW208L | User Guide - Page 82
    EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) This document contains important information for users with regards to the proper disposal and recycling of Linksys your local authorities, waste disposal service, or the shop where Port 10/100 Ethernet Switch with Webview 76
  • Cisco SRW208L | User Guide - Page 83
    2002/96/EC Français (French) - Informations environnementales pour les clients de l'Union européenne La directive européenne 2002/96/CE prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l'endroit où vous jumu. 8-Port 10/100 Ethernet Switch with Webview 77
  • Cisco SRW208L | User Guide - Page 84
    u het product hebt aangeschaft. Norsk (Norwegian) - Miljøinformasjon for kunder i EU EU-direktiv 2002/96/EF krever at utstyr med følgende symbol avbildet på produktet og władz, służb oczyszczania miasta lub sklepu, w którym produkt został nabyty. 8-Port 10/100 Ethernet Switch with Webview 78
  • Cisco SRW208L | User Guide - Page 85
    (Portuguese) - Informação ambiental para clientes da União Europeia A Directiva Europeia 2002 Suomi (Finnish) - Ympäristöä koskevia tietoja EUalueen asiakkaille EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä visit www.linksys.com 8-Port 10/100 Ethernet Switch with Webview 79
  • Cisco SRW208L | User Guide - Page 86
    Line 800-546-5797 (LINKSYS) Support 800-326-7114 RMA (Return Merchandise Authorization) http://www.linksys.com/warranty NOTE: Details on warranty and RMA issues can be found in the Warranty section of this Guide. Contact Information 8-Port 10/100 Ethernet Switch with Webview 7120510B-SM
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
USER GUIDE
BUSINESS SERIES
8-Port 10/100 Ethernet
Switch with Webview
Model:
SRW208/SRW208G/SRW208L/SRW208P/SRW208MP