Cisco SRW208MP Hardware Installation Guide

Cisco SRW208MP Manual

Get Cisco SRW208MP PDF manuals and user guides View all Cisco SRW208MP manuals
Add to My Manuals
Save this manual to your list of manuals

Cisco SRW208MP manual content summary:

  • Cisco SRW208MP | Hardware Installation Guide - Page 1
    Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide March 2008 THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE
  • Cisco SRW208MP | Hardware Installation Guide - Page 2
    , if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of IP addresses in illustrative content is unintentional and coincidental. Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide © 2008 Cisco
  • Cisco SRW208MP | Hardware Installation Guide - Page 3
    2-2 Safety Warnings 2-3 AC Power Option Warnings 2-6 DC Power Option Warnings 2-6 Safety Guidelines 2-6 General Precautions 2-6 Protecting Against Electrostatic Discharge 2-7 Safety Information 2-8 Emissions Disclaimer 2-8 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide iii
  • Cisco SRW208MP | Hardware Installation Guide - Page 4
    Initially Configuring a CDE 4-14 Assigning the Primary Interface 4-14 Running the Setup Utility 4-15 Verifying the CDSM 4-15 Hardware Troubleshooting 5-1 Troubleshooting Ethernet Adapters 5-1 Troubleshooting SATA Drives 5-2 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide
  • Cisco SRW208MP | Hardware Installation Guide - Page 5
    CDE300 D-5 Disconnecting Power and Replacing a PM on a CDE300 D-7 Connecting DC Power to a CDE400 D-7 Disconnecting Power and Replacing a PM on a CDE400 D-10 DC Power Cable Connector and Pinouts D-11 Contents OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide v
  • Cisco SRW208MP | Hardware Installation Guide - Page 6
    Contents Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide vi OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 7
    Safety Information Referral Warning, page ix • Obtaining Documentation and Submitting a Service Request, page xv Document Revision History The Document Revision History table below CDS hardware components. OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide vii
  • Cisco SRW208MP | Hardware Installation Guide - Page 8
    CDS 2.0-2.1 Software Configuration Guide • Cisco Internet Streamer CDS 2.0-2.1 Quick Start Guide • Cisco Internet Streamer CDS 2.0-2.1 API Guide • Cisco Content Delivery System 2.x Documentation Roadmap • Regulatory Compliance and Safety Information for the Cisco Content Delivery Engine 100/200/300
  • Cisco SRW208MP | Hardware Installation Guide - Page 9
    number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071 SAVE THESE INSTRUCTIONS OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide ix
  • Cisco SRW208MP | Hardware Installation Guide - Page 10
    qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS Warnung riportate in questo documento. CONSERVARE QUESTE ISTRUZIONI Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide x OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 11
    som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide xi
  • Cisco SRW208MP | Hardware Installation Guide - Page 12
    o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo. GUARDE ESTAS INSTRUÇÕES Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide xii OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 13
    . Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide xiii
  • Cisco SRW208MP | Hardware Installation Guide - Page 14
    Preface Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide xiv OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 15
    as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0. OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide xv
  • Cisco SRW208MP | Hardware Installation Guide - Page 16
    Preface Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide xvi OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 17
    the CDE installation and initialization, you are asked to select a device mode. The following device modes are supported: • Content Delivery System Manager (CDSM) • Service Engine (SE) • Service Router (SR) OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 1-1
  • Cisco SRW208MP | Hardware Installation Guide - Page 18
    supports device-mode configuration and can be configured with the CDS 2.0-2.1 software to operate as an SE, SR, or a CDSM. Cisco TV CDS Overview The Cisco CDE200). The CDSM is used to manage the Vaults and Streamers, collect event a form of caching across Gigabit Ethernet networks. All content is
  • Cisco SRW208MP | Hardware Installation Guide - Page 19
    • Decisions on content retention on Streamer servers Hardware Features The Cisco Internet Streamer and TV CDS Release 2.0-2.1 CDEs are the CDE100 AC power option. Figure 1-3 CDE200 Front View 12 211765 OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 1-3
  • Cisco SRW208MP | Hardware Installation Guide - Page 20
    210821 Figure 1-5 shows the front view of the CDE300 and Figure 1-6 shows the rear view of the CDE300 with the AC power option. Figure 1-5 CDE300 Front View 270603 Figure 1-6 CDE300 Rear View 270594 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 1-4 OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 21
    Intel 4 GB Xeon processor 2 2 dual-core Intel 8 GB Xeon processors Drives 4 150-GB Small Computer System Interface (SCSI) drives 12 500-GB Serial ATA (SATA) drives GE Ports 2 6 Ethernet Interface - 11 OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 1-5
  • Cisco SRW208MP | Hardware Installation Guide - Page 22
    drive tray. Note You may need to use a pen or the end of a straightened paper clip to press the Power and Reset buttons. The Reset button does not restore the device to the factory default software settings. Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 1-6 OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 23
    , and describes the front panel control buttons. Figure 1-11 CDE300 Front Panel Control Buttons 12 270625 1 Power 2 Reset Powers up the device. Resets the device and runs the power-on self-test (POST). OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 1-7
  • Cisco SRW208MP | Hardware Installation Guide - Page 24
    1 Power 2 Reset 1 2 Powers up the device. Resets the device and runs the power-on self-test (POST). LED Indicators Figure 1-13 shows the location of the CDE100 front panel LEDs, and describes their functions. Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 1-8 OL
  • Cisco SRW208MP | Hardware Installation Guide - Page 25
    1 Power 2 Hard disk drive activity 3 Ethernet port 1 4 Ethernet port 2 Color Blue Blue Blue Blue State On On On On Description Device is powering on. A hard disk drive is in use. Port is connected. Port is connected. Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 1-9
  • Cisco SRW208MP | Hardware Installation Guide - Page 26
    Panel LEDs 12 270626 270627 No. LED Color 1 Hard disk drive power Blue 2 Hard disk drive activity Blue State On On Description Power is flowing to the device. Associated hard disk drive is in use. 1-10 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 27
    are supported by the BIOS for POST, and the BIOS Setup Utility as described in Chapter 4, "Installing the Internet Streamer CDS Software and Initially Configuring a CDE." Figure 1-18 shows the location of the CDE200 back panel ports and connectors. OL-13478-03 Cisco Content Delivery Engine 100/200
  • Cisco SRW208MP | Hardware Installation Guide - Page 28
    In this hardware configuration, the Gigabit Ethernet interfaces on the motherboard are addressed as interfaces 3/0 and 4/0, and the interfaces on the NICs are detected as 1/0, 2/0, 5/0, and 6/0. The interface numbering must be taken into consideration when configuring IP addresses and port channels
  • Cisco SRW208MP | Hardware Installation Guide - Page 29
    ports and connectors. Figure 1-20 CDE400 Connector Locations 4 5 67 8 3 2 1 1 Power connectors Management Interface (eth0) 7 Ingest Interface (eth1) 8 Cache/Stream interfaces (eth2 through eth7) 270604 OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide
  • Cisco SRW208MP | Hardware Installation Guide - Page 30
    Hardware Features Chapter 1 Overview of the Content Delivery Engines 1-14 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 31
    100/200/300/400 document that came with your device before you begin the installation. Site Requirements This section provides site requirements for the CDEs. You should verify the site power prior to installing the CDEs. Preventing Electrostatic Discharge Damage The CDEs have no user-serviceable
  • Cisco SRW208MP | Hardware Installation Guide - Page 32
    1 and 10 megohm (Mohm). Environmental, Physical, and Power Specifications The CDEs are tested to the environmental specifications indicated .3 cm) 2.0 inches (7.6 cm) 1.0 inches (2.5 cm) 3.6 inches (9.2 cm) Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 2-2 OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 33
    Compliance and Safety Information for the Cisco Content Delivery Engine 100/200/300/400 document that ships with the CDEs. Warning Read the installation instructions before you connect the system to its power source. Statement 10 Warning The ports labeled "Ethernet," "10BaseT," "Token Ring
  • Cisco SRW208MP | Hardware Installation Guide - Page 34
    Read the installation instructions before connecting the system to the power source. Statement 1004 circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 2-4 OL-
  • Cisco SRW208MP | Hardware Installation Guide - Page 35
    chassis using the handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to support the weight of the unit. Statement 1032 Warning connection. Statement 1078 OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 2-5
  • Cisco SRW208MP | Hardware Installation Guide - Page 36
    and replace the part or contact your authorized service provider: - The power cable or plug is damaged. - An instructions. • Keep your system components away from radiators and heat sources. Also, do not block cooling vents. Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide
  • Cisco SRW208MP | Hardware Installation Guide - Page 37
    products plugged into the power strip does not exceed 80 percent of the power strip ampere ratings limit. • Do not use appliance or voltage converters or kits sold for appliances with pads and workbench pads. OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 2-7
  • Cisco SRW208MP | Hardware Installation Guide - Page 38
    into an AC outlet that is part of the rack, then you must provide proper grounding for the rack itself. If the server power cord is plugged into a wall AC outlet, the safety ground conductor in the power cord Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 2-8 OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 39
    power system for the equipment rack is installed with more than 10 amperes of protection, you must provide supplemental protection for the server. The overall current rating of a maximum configured 1002 OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 2-9
  • Cisco SRW208MP | Hardware Installation Guide - Page 40
    ventilation sufficient to exhaust a maximum of 1023 BTUs (British Thermal Units) per hour for the server. The rack selected and the ventilation provided must be suitable to the environment in which the server will be used. 2-10 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation
  • Cisco SRW208MP | Hardware Installation Guide - Page 41
    Manager (CDSM)-CDE100 or CDE200 • Service Engine (SE)-CDE200 • Service Router (SR)-CDE200 Depending on your application, you may have multiple SEs and SRs. A network switch Streamer Vault (ISV)-CDE200 OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 3-1
  • Cisco SRW208MP | Hardware Installation Guide - Page 42
    switch 16-inch flat-blade screwdriver • Number 2 Phillips screwdriver Unpacking the Box Each Cisco CDE is securely packaged in a shipping box. The cards and power supplies ship installed in the CDEs. Caution Proper ESD protection is required whenever you handle Cisco Cisco accessory kits and
  • Cisco SRW208MP | Hardware Installation Guide - Page 43
    of the dated proof-of-purchase, to the Cisco Systems Corporate Service Center or an authorized Cisco Systems service center during the applicable warranty period. Contact Cisco Technical Support for the location of your nearest service center. Note Before proceeding with the installation, verify
  • Cisco SRW208MP | Hardware Installation Guide - Page 44
    outlet. • Do not overload the power outlet when installing multiple devices in the rack. • Do not place any object weighing more than 110 lb (50 kg) on top of rack-mounted devices. Preparing the CDEs for Rack Installation Verify correct hardware configuration by performing the following steps
  • Cisco SRW208MP | Hardware Installation Guide - Page 45
    CDE110 in a Rack" section in the Cisco Content Delivery Engine 110 Hardware Installation Guide at the following URL: http://www.cisco.com/en/US/docs/video/cds/cde/cde110/installation/guide/ch3_inst.html#wp1051129 Note The CDE300 and CDE400 ship with a rack mounting kit and instructions. Caution At
  • Cisco SRW208MP | Hardware Installation Guide - Page 46
    3 1 Power connectors 2 Mouse connector 3 Keyboard connector 4 Serial console interface 4 5 67 5 VGA interface 6 Management interface (eth0) 7 Ingest interface (eth1) 8 Stream interfaces (eth2 through eth5) 211771 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 3-6 OL
  • Cisco SRW208MP | Hardware Installation Guide - Page 47
    eth5 eth13 eth9 eth3 eth1 76 1 Power connectors 2 Serial console interface 3 VGA interface 4 Management interface (eth0) 5 5 5 5 Cache/stream interfaces 6 Mouse connector 7 Keyboard connector 270606 OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 3-7
  • Cisco SRW208MP | Hardware Installation Guide - Page 48
    2 270604 1 1 Power connectors 2 Mouse connector 3 Keyboard connector 4 Serial console interface 5 VGA interface 6 Management Interface (eth0) 7 • Vault to switch • Streamer to switch • CDSM to switch Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 3-8 OL-13478-
  • Cisco SRW208MP | Hardware Installation Guide - Page 49
    disk drives (see Figure 3-7), the CDE300 contains 16 disk drives (see Figure 3-8), and the CDE400 contains 24 disk drives (see Figure 3-9). Figure 3-6 CDE100 Disk Drive Locations sda sdb sdc sdd 211859 OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 3-9
  • Cisco SRW208MP | Hardware Installation Guide - Page 50
    changes depending on the bios settings. The code dynamically establishes the drive configuration at run time. Figure 3-8 CDE300 Disk Drive Locations 211772 270603 270615 disk22 disk30 disk38 disk46 3-10 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 51
    your hand or any metal tool, or you could shock yourself. Statement 94 Step 1 Step 2 Power off the CDE before removing or installing a disk drive. To access the disk drives on a CDE200 button. 203854 OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 3-11
  • Cisco SRW208MP | Hardware Installation Guide - Page 52
    the servers are powered up, a Cisco technician will initially configure the servers to be able to communicate properly. Further configuration is accomplished through the CDSM. See the Cisco TV CDS Software Configuration Guide for more information. 3-12 Cisco Content Delivery Engine 100/200/300/400
  • Cisco SRW208MP | Hardware Installation Guide - Page 53
    CDE200, use the USB port to connect the USB CD-ROM drive. After the initial installation, remove the USB CD-ROM drive. The internal IDE compact flash drive becomes the boot drive for subsequent operations. OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 4-1
  • Cisco SRW208MP | Hardware Installation Guide - Page 54
    also need to configure the ports on the CDE200 as shown below: • The two built-in Gigabit Ethernet ports are GigabitEthernet 1/0 and GigabitEthernet 2/0 and are management ports using channel bonding 1 (see Figure 1-18). Ethernet Management Ports eth0 eth1 Gigabit Ethernet Management Ports g1/0 g2
  • Cisco SRW208MP | Hardware Installation Guide - Page 55
    Configuring a CDE Running the BIOS Setup Utility Running the BIOS Setup Utility for the CDE100 Perform the following steps to run the BIOS setup utility for the CDE100: Step 1 Step 2 Step 3 Power 4-2). OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 4-3
  • Cisco SRW208MP | Hardware Installation Guide - Page 56
    Boot Settings Configuration Screen Step 7 a. Set the Quick Boot option to Enabled. b. Set the Quiet Boot option to Disabled. Press Esc to return to the Boot menu and choose Boot Device Priority. The Boot Device Priority screen appears (see Figure 4-4). Cisco Content Delivery Engine 100/200/300
  • Cisco SRW208MP | Hardware Installation Guide - Page 57
    CDS Software and Initially Configuring a CDE Figure 4-4 Boot Device Priority Screen Running the BIOS Setup Utility Step 8 Use the on-screen instructions to move the elements into (see Figure 4-6). OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 4-5
  • Cisco SRW208MP | Hardware Installation Guide - Page 58
    is connected to a 128-MB compact flash drive. Step 12 Press Esc to return to the Advanced menu. Choose Super I/O Configuration and press Enter. The Configure Super I/O Chipset screen appears (see Figure 4-8). Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 4-6 OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 59
    Port Mode option to 9600 8, n, 1. c. Set the Redirection After BIOS POST option to Disabled. When you are finished, navigate to the Exit submenu and choose Save and Exit. Press OK when prompted (see Figure 4-10). OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide
  • Cisco SRW208MP | Hardware Installation Guide - Page 60
    . Your configuration is saved, you exit the BIOS Setup menu, 9. Force manufacturing flash Choice [0]: Step 16 Confirm that the FLASHDEV: line near Cisco Technical Support at the following URL: www.cisco.com/techsupport Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide
  • Cisco SRW208MP | Hardware Installation Guide - Page 61
    Configuring a CDE Running the BIOS Setup Utility Running the BIOS Setup Utility for the CDE200 Perform the following steps to run the BIOS setup utility for the CDE200: Step 1 Step 2 Step 3 Step 4 Ensure that the CDE200 is powered off. Attach the USB CD-ROM drive to any available USB port
  • Cisco SRW208MP | Hardware Installation Guide - Page 62
    option to Enabled. b. Set the Quiet Boot option to Disabled. c. Set the After Power Failure option to Power On. Use the Down Arrow key to expand +Hard Drive and expose its subelements (see Figure 4-14). 4-10 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 63
    Streamer CDS Software and Initially Configuring a CDE Figure 4-14 Hard Disk Drives Screen Running the BIOS Setup Utility Step 9 Use the on-screen instructions to move the elements into a 128-MB compact flash drive. Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 4-11
  • Cisco SRW208MP | Hardware Installation Guide - Page 64
    first power-on. In this case, the CD-ROM drive is not present in the above Hard Drive element list. Press the Reset button (not the Power button) and try again. If it still fails, try a different USB CD-ROM drive. 4-12 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide OL
  • Cisco SRW208MP | Hardware Installation Guide - Page 65
    Streamer CDS Software and Initially Configuring a CDE Installing the Software b. If the USB CD-ROM drive is still not detected (not shown), press the Reset button again. If you are still unable to detect the CD-ROM drive at the BIOS level, contact Cisco Technical Support at the following URL: www
  • Cisco SRW208MP | Hardware Installation Guide - Page 66
    Interface GigabitEthernet 1/0 is chosen by default to be the primary interface. Enter the following commands to assign a primary interface: CDE# configure CDE(config)# primary-interface GigabitEthernet 1/0 4-14 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 67
    CDStr1 Please enter CDSM (Content Delivery System Manager) IP or Host name: 209.165.201.0 Press any key to continue CDE# configure terminal CDE# cms enable This process initiates database services on the device that you just configured. Note Once the IP default gateway has been set, we recommend
  • Cisco SRW208MP | Hardware Installation Guide - Page 68
    Initially Configuring a CDE Figure 4-18 CDSM Login Page Step 2 Enter admin as the username and default as the password and press Login. The CDSM Main menu appears (see Figure 4-19). Figure 4-19 CDSM Main Menu 4-16 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide OL
  • Cisco SRW208MP | Hardware Installation Guide - Page 69
    registered Service Engines and Service Routers appears (see Figure 4-20). Figure 4-20 Devices Page Step 4 Step 5 Verify that the devices you configured for complete. Refer to the Cisco Internet Streamer CDS 2.0-2.1 Software Configuration Guide for information on configuring and using the CDS
  • Cisco SRW208MP | Hardware Installation Guide - Page 70
    Verifying the CDSM Chapter 4 Installing the Internet Streamer CDS Software and Initially Configuring a CDE 4-18 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 71
    . CDEs use dual-port and quad-port Intel adapters. Driver and diagnostic utilities are available on each vendor's website. You may also contact Cisco Technical Support at this URL: www.cisco.com/techsupport OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 5-1
  • Cisco SRW208MP | Hardware Installation Guide - Page 72
    Troubleshooting Troubleshooting of 24 SATA drives problem persists, replace the drive with a known good drive. If the problem still persists, contact Cisco Technical Support at the following URL: www.cisco.com/techsupport Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide
  • Cisco SRW208MP | Hardware Installation Guide - Page 73
    CDEs. It includes the following sections: • Specifications, page A-1 • Management, page A-4 Note This appendix only provides information on CDEs that were contains the technical specifications for the CDEs. OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide A-1
  • Cisco SRW208MP | Hardware Installation Guide - Page 74
    configured) Approvals: Safety Approvals: EMC 2 6-TB SATA (12x 500-GB SATA) 8 Gigabytes DRAM Copper: Four 10/100/1000BASE-T Fiber: Four 1000BASE-SX Two 10/100/1000BASE-T on motherboard, one for out-of-band management; One serial port for console 128MB None 115-240 VAC or -48 VDC; Redundant power
  • Cisco SRW208MP | Hardware Installation Guide - Page 75
    (fully configured) Approvals: Safety Approvals: EMC 3 1.15-TB SCSI (16x 73-GB SCSI disks) 16 Gigabytes DRAM Copper: Twelve 10/100/1000BASE-T; Fiber: Eight 1000BASE-SX Two 10/100/1000BASE-T on motherboard of which one used for out-of-band management; One serial port for console None None 100-240
  • Cisco SRW208MP | Hardware Installation Guide - Page 76
    Cables 2 Gbps maximum Console port: DB-9 RS-232 10/100/1000 Mbps Ethernet interface: RJ-45 (management) For console port: DB-9 female serial cable For Ethernet interface: RJ-45 Category 5E or higher cable Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide A-4 OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 77
    ; output 7 Out Clear to send; input 8 In Ring indicator; input 9 In Signal Name DCD RXD TXD DTR GND DSR RTS CTS RI OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide B-1
  • Cisco SRW208MP | Hardware Installation Guide - Page 78
    the industry standard for RS-232 communications. Figure B-1 1 Serial Port Connector 5 83193 6 9 Ethernet Connector Pin Assignments The Ethernet connector 1000BASE-T Signal BI_DA+ BI_DA- BI_DB+ BI_DC+ Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide B-2 OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 79
    Ethernet port, connect a Category 3, 4, or 5 unshielded twisted-pair (UTP) cable to the RJ-45 connector on the back of the device. Note The 100BASE-TX/1000BASE-TX Ethernet standard requires that the cabling in the network be Category 5 or higher. OL-13478-03 Cisco Content Delivery Engine 100/200
  • Cisco SRW208MP | Hardware Installation Guide - Page 80
    pin number assignments for the Ethernet RJ-45 port. Figure 2-2 RJ-45 Ethernet Port Connector Activity LED (green) Link LED ( 2 3 4 5 6 TO HOST COMPUTER 7 8 9 DB-9 (Female) End view 51 96 211777 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide B-4 OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 81
    Assignments and Wiring for an RJ-45 Crossover Cable 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown 211779 OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide B-5
  • Cisco SRW208MP | Hardware Installation Guide - Page 82
    Cable Pin Assignments Appendix B Connector Pin Assignments Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide B-6 OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 83
    interface 4 Gigabytes RAM Pentium 4 @ 3.6 GHz 800-MHz FSB, 1-MB Cache IP, SNMP, FTP, Gigabit Ethernet, SSH Red Hat 9.0 distribution supporting Linux kernel 2.4.30 60 GB small form factor IDE hard drive Maximum length of 330 ft (100 m) using Category 5E or higher Integrate with both the Tandberg and
  • Cisco SRW208MP | Hardware Installation Guide - Page 84
    . (8.90 × 44.45 × 72.39 cm) Chassis fully configured (all slots filled): 53.5 lb. (24.27 kg) Content Storage Capacity Management Interface 12 Serial-ATA 320, 400, or 500 GB hard drives 1 Gigabit Ethernet interface Ingest Interface 1 Gigabit Ethernet interface Stream Interfaces Transport Memory
  • Cisco SRW208MP | Hardware Installation Guide - Page 85
    12 Gigabit Ethernet interfaces for cache and stream traffic High Definition MPEG-2 and Advanced Codec; Pre-encryption and Network PVR is fully supported 16 Gigabytes RAM Two Dual Xeon @ 3.2 GHz (or above) OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide C-3
  • Cisco SRW208MP | Hardware Installation Guide - Page 86
    System Disk Cable length Performance Monitoring Power Fan Assembly Operating Temperature Humidity Short Term Humidity Altitude IP, SNMP, FTP, Gigabit Ethernet, SSH, FSI, DSM-CC, LSCP, RTSP Ultra320 SCSI Enterprise Linux 3 is the supported operating system 60-GB small form-factor IDE hard drive
  • Cisco SRW208MP | Hardware Installation Guide - Page 87
    8 1 Power connectors 2 Mouse connector 3 Keyboard connector 4 VGA interface 5 Serial console interface 6 Management Interface (eth1) 7 Stream interfaces (eth3, eth4, eth5) 8 Ingest Interface (eth2) 270612 OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide C-5
  • Cisco SRW208MP | Hardware Installation Guide - Page 88
    hardware configuration, the Gigabit Ethernet interfaces on the motherboard are detected as interfaces 3/0 and 4/0, and the interfaces on the NICs are detected as 1/0, 2/0, 5/0, and 6/0. The interface numbering must be taken into consideration when configuring IP addresses and port channels. Figure
  • Cisco SRW208MP | Hardware Installation Guide - Page 89
    VGA interface 6 Management interface (eth2) 7 Ingest interface (eth1) 8 Cache/Stream interfaces (eth3 through eth6) Figure C-6 shows the location of all the connectors for a CDE400 with six cache interfaces. OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide C-7
  • Cisco SRW208MP | Hardware Installation Guide - Page 90
    4 Serial console interface eth0 eth1 eth6 eth5 eth8 eth2 eth4 eth7 eth3 270609 5 VGA interface 6 Management interface (eth0) 7 Cache/Stream interfaces (eth3 through eth8) 8 Ingest interface (eth2) Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide C-8 OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 91
    to a dedicated 60A regulated source. Figure D-1 shows a DC PM for a CDE200. Figure D-1 DC Power Module for a CDE200 280163 Note In this chapter, the power supply is referred to as a "power module." OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide D-1
  • Cisco SRW208MP | Hardware Installation Guide - Page 92
    Step 1 Step 2 Insert a blue DC power cable connector into the blue port on each PM, making sure it is completely power cable connector over the PM ground stud in the following order and secure with the nut (see Figure D-3): Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide
  • Cisco SRW208MP | Hardware Installation Guide - Page 93
    of electrostatic discharge. This connection should be installed by a trained service person and the equipment is to be installed per local code or used for the DC power connections (-48 VDC and +Return). OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide D-3
  • Cisco SRW208MP | Hardware Installation Guide - Page 94
    4 Step 5 Remove the +Return (red) and -48 VDC (black) DC power wires from your power source. Remove the PM ground wires (green and yellow) from the PM ground stud DC Power to a CDE200" section on page D-2. Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide D-4 OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 95
    on the CDE. Step 1 Step 2 Insert one blue DC power cable connector into the blue port on each PM, making sure it is completely seated. Remove the nut and star washers from the Building/PM ground stud. OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide D-5
  • Cisco SRW208MP | Hardware Installation Guide - Page 96
    the end of the ground wires (green and yellow) attached to the DC power cable connector over the Building/PM ground stud in the following order and secure wrench to tighten the nut and secure the connection. Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide D-6 OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 97
    service you must first disconnect DC power and remove the PM from VDC (black) DC power wires from your power source. Remove the PM Power to a CDE300" section on page D-5. Reconnect the +Return (red) and -48 VDC (black) DC power wires to your power source. Connecting DC Power connecting DC power to a
  • Cisco SRW208MP | Hardware Installation Guide - Page 98
    not attached to the DC power source until all the ground wires are connected on the CDE. Step 1 Insert one blue DC power cable connector into the blue port on each PM, making sure it is completely seated. Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide D-8 OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 99
    the ring lug at the end of the ground wires (green and yellow) attached to the DC power cable connectors in PM 1 and PM 2 over PM ground stud 1 in the following order the ground wires (green and yellow) attached to the DC power cable connectors in PM 3 and PM 4 over PM ground stud 2 in the following
  • Cisco SRW208MP | Hardware Installation Guide - Page 100
    and yellow) to the PM ground studs as described in Step 2 of the "Connecting DC Power to a CDE400" section on page D-7. Reconnect the +Return (red) and -48 VDC (black) DC power wires to your power source. D-10 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 101
    . Figure D-9 DC Power Cable and Pinouts 12 This illustration is in progress. 1 4 2 5 3 6 280163 3 4 5 6 1 +Return 2 -48 VDC 3 PM ground 4 PM ground wire and ring lug 5 -48 VDC wire and ring lug 6 +Return wire and ring lug OL-13478-03 Cisco Content Delivery Engine 100/200/300/400
  • Cisco SRW208MP | Hardware Installation Guide - Page 102
    DC Power Cable Connector and Pinouts Appendix D Connecting DC Power D-12 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 103
    safety warnings 2-3 specifications A-2 CDE200 BIOS Setup 4-9 configuring ports 4-2 connecting DC power D-2 connectors 1-12, 3-6 control buttons 1-7 disk drives 3-9 front cover 1-9, 3-11 hardware features 1-5 LEDs 1-9 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide IN-1
  • Cisco SRW208MP | Hardware Installation Guide - Page 104
    power 2-9 Cisco Technical Assistance 5-2 Common Bonding Network (CBN) 2-9 configuration assigning a primary interface 4-14 CDE 4-14 order 4-2 running Setup 11 Ethernet 1-11, B-3 Gigabit Ethernet 4-2 I/O 1-11 IN-2 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide OL-13478-03
  • Cisco SRW208MP | Hardware Installation Guide - Page 105
    Manager, see CDSM control buttons CDE100 1-6 CDE200 1-7 CDE300 1-7 CDE400 1-8 D DC power adapter troubleshooting 5-1 Ethernet port cabling requirements Gigabit Ethernet connectors 4-2 ports 4-2 Gigabit Ethernet Modules A-4 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide
  • Cisco SRW208MP | Hardware Installation Guide - Page 106
    D-7 the rack installation 2-8 H hardware CDE100 features 1-5 CDE200 features 1-5 CDE300 features 1-6 CDE400 features 1-6 overview 1-3 hardware troubleshooting, see troubleshooting I IDE compact flash drive 4-1, 4-13 ingest interface 1-11 initially configuring CDEs 4-1 installation BIOS Setup utility
  • Cisco SRW208MP | Hardware Installation Guide - Page 107
    DC power 2-6 SE 1-1, 3-1 connections 3-8 serial connector 1-11 ports B-2 connector pinout B-2 serial console interface 1-11, B-1 server types CDSM 1-1, 3-1 ISV 3-1 SE 1-1, 3-1 SR 1-1, 3-1 streamer 3-1 vault 3-1 OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide
  • Cisco SRW208MP | Hardware Installation Guide - Page 108
    specifications C-1 Service Engine, see SE Service Router, see SR site requirements 2-1 specifications CDE100 A-2 CDE200 A-2 CDE300 A-3 CDE400 A-3 management A-4 2-2, 2-10 terminal server parameters 4-1 IN-6 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide OL-13478-03
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Cisco Content Delivery Engine 100/200/300/400
Hardware Installation Guide
March 2008
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO
CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS
MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY
PRODUCTS.
Text Part Number: OL-13478-03