Cisco WS-C3560X-48PF-L Hardware Installation Guide

Cisco WS-C3560X-48PF-L Manual

Cisco WS-C3560X-48PF-L manual content summary:

  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 1
    Catalyst 3750-X and 3560-X Switch Hardware Installation Guide June 2011 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 2
    it is not installed in accordance with Cisco's installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 3
    14 Master LED (Catalyst 3750-X) 1-14 Stack LED (Catalyst 3750-X) 1-14 PoE+ LED 1-15 Network Module LEDs 1-16 USB Mini-Type B Port 1-17 Rear Panel Description 1-17 RJ-45 Console Port LED 1-18 USB Type A Interface 1-18 StackWise Ports 1-19 Power Supply Modules 1-19 Switch Power Supply Modules 1-19 OL
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 4
    2-5 Data Stack Cabling Configurations 2-5 Data Stack Bandwidth and Partitioning Examples 2-7 Power On Sequence for Switch Data Stacks 2-8 Planning a StackPower Stack (Catalyst 3750-X Switches) 2-8 StackPower Stacking Guidelines 2-8 StackPower Cabling Configurations 2-9 StackPower Partitioning
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 5
    3-15 Troubleshooting 4-1 Diagnosing Problems 4-1 Switch POST Results 4-1 Switch LEDs 4-1 Switch Connections 4-2 Bad or Damaged Cable 4-2 Ethernet and Fiber Cables 4-2 Link Status 4-2 10/100/1000 Port Connections 4-3 PoE Port Connections 4-3 SFP Modules 4-3 Interface Settings 4-4 Ping End Device
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 6
    Catalyst 3750-X Switches) 4-6 Technical Specifications A-1 Switch Specifications A-1 Power Supply Module Specifications A-2 Fan Module Specifications A-4 Connector and Cable Specifications B-1 Connector Specifications B-1 10/100/1000 Ports B-1 10 Gigabit Ethernet CX1 (SFP+ Copper) Connectors B-2 SFP
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 7
    Windows XP and 2000 USB Driver C-5 Uninstalling the Cisco Microsoft Windows Vista and Windows 7 USB Driver C-6 Entering the Initial Configuration Information C-6 IP Settings C-6 Configuring the Setup Program C-6 OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide vii
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 8
    Contents Catalyst 3750-X and 3560-X Switch Hardware Installation Guide viii OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 9
    Started Guide • Catalyst 3750-X and 3560-X Switch Hardware Installation Guide • Regulatory Compliance and Safety Information for the Catalyst 3750-X and 3560-X Switch • Installation Notes for the Catalyst 3750-X, Catalyst 3560-X Switch Power Supply Modules • Installation Notes for the Catalyst 3750
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 10
    Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0. Catalyst 3750-X and 3560-X Switch Hardware Installation Guide x OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 11
    3750-X Switch Models Switch Model Cisco IOS Image Catalyst 3750-X-24T-L LAN Base image Catalyst 3750-X-48T-L LAN Base image Catalyst 3750-X-24P-L LAN Base image Catalyst 3750-X-48P-L LAN Base image Catalyst 3750-X-48PF-L LAN Base image Catalyst 3750-X-24T-S IP Base image3 Description
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 12
    supply Catalyst 3750-X-24S-E IP Services image 24 SFP module slots, StackWise Plus, StackPower, 1 network module1 slot, 350-W power supply 1. Available network modules: 10-Gigabit Ethernet network module; 1-Gigabit Ethernet network module; blank module (see Table 1-3 on page 1-6). 2. PoE+ = Power
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 13
    3560-X-24T-S IP Base image3 Catalyst 3560-X-48T-S IP Base image3 Catalyst 3560-X-24P-S IP Base image3 Catalyst 3560-X-48P-S IP Base image3 Catalyst 3560-X-48PF-S IP Base image3 Description 24 10/100/1000 Ethernet ports, 1 network module1 slot, 350-W power supply 48 10/100/1000 Ethernet ports
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 14
    and Catalyst 3750-X-24S switch support any combination of standard SFP modules. SFP+ modules are not supported. Note For information about about the (uplink) SFP and SFP+ module slots on the network modules, see the "Network Modules" section on page 1-5. See Table 1-4 for a list of supported SFP
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 15
    Support for Cisco enhanced PoE • Support for prestandard Cisco powered devices • Configuration for StackPower PoE+. When the switch internal power supply module(s) cannot support the total load, StackPower configurations allow the switch to leverage power available from other switches (only Catalyst
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 16
    Service Module C3KX-SM-10G This module has two slots that support either 1-Gigabit SFP or 10-Gigabit SFP+ modules. The service module supports For cable specifications, see Appendix B, "Connector and Cable Specifications." Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 1-6 OL-19593
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 17
    connections. Use only Cisco SFP modules on the switch. Note The (downlink) SFP module slots on the Catalyst 3750-X-12S and Catalyst 3750-X-24S switch front panel support any combination of standard SFP modules. SFP+ modules are not supported. Table 1-4 Supported Cisco SFP Modules Part Number
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 18
    1-4 Supported Cisco SFP Modules (continued) Part Number DWDM-SFP-3033= DWDM-SFP-3112= DWDM-SFP-3190= DWDM-SFP-3268= DWDM-SFP-3346= DWDM-SFP-3425= DWDM-SFP-3504= DWDM-SFP-3582= DWDM-SFP-3661= DWDM-SFP-3739= DWDM-SFP-3819= DWDM-SFP-3898= DWDM-SFP-3977= DWDM-SFP-4056= DWDM-SFP-4134= DWDM-SFP-4214
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 19
    " section on page 2-24. For cable specifications, see Appendix B, "Connector and Cable Specifications." The Catalyst 3560-X switch supports the SFP module patch cable (CAB-SFP-50CM), a 0.5-meter, copper, passive cable with SFP module connectors at each end. This cable is only used with 1-Gigabit
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 20
    -related) • Power supply • Fan module System is receiving power but is not functioning properly. For information on the System LED colors during power-on self-test (POST), see the "Diagnosing Problems" section on page 4-1. 1-10 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 21
    PoE+2 StackWise port status The StackWise port status. See the "Stack LED (Catalyst 3750-X)" section on page 1-14. PoE+ port power The PoE+ port status. 1. Only Catalyst 3750-X switches. 2. Only switches with PoE+ ports. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 22
    up to 30 seconds as STP checks the switch for possible loops. SPEED 10/100/1000/SFP ports Off Port is operating at 10 Mb/s. Green Port is operating at 100 Mb/s. Single numbers of other stack member switches. 1-12 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 23
    or because it has exceeded a limit set in the switch software. Caution PoE+ faults are caused when noncompliant cabling or powered devices are connected to a PoE+ port. Use only standard-compliant cabling to connect Cisco prestandard IP Phones and wireless access points or IEEE 802.3af-compliant
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 24
    , or administrative action is required. See the switch software configuration guide for information about configuring StackPower. The StackPower budget is not sufficient to meet current power demands. Master LED (Catalyst 3750-X) Table 1-12 Color Off Green Amber Master LED Description Switch
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 25
    . PoE+ mode is selected, and the port LEDs show the PoE+ status. PoE+ mode is not selected. At least one of the 10/100/1000 ports has been denied power, or at least one of the 10/100/1000 ports has a PoE+ fault. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 1-15
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 26
    47 48 PoE+48 SFP or SFP+ port. Use only standard-compliant cabling to connect to Cisco SFP and SFP+ ports. You must remove from the network any cable or device that causes a link fault. Link for the SFP or SFP+ has been disabled. 1-16 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 27
    7 Reset button 8 Fan modules 9 StackPower or XPS 2200 connector 10 StackPower connector 11 Power supply modules (AC power supply modules shown) 12 AC power (input) status LED 13 Power supply (output) status LED OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 1-17
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 28
    connector 9 Power supply module slot (blank module shown) 10 Power supply module (AC power supply module shown) 11 AC power (input) status LED 12 Power supply (output) guide and the command reference on Cisco.com and the "Connector and Cable Specifications" section on page B-1. 1-18 Catalyst
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 29
    has a power cord for connection to an AC power outlet. The 1100-W and 715-W modules use a 16-AWG cord (only North America). All other modules use an 18-AWG cord. The DC-power supply module must be wired to a DC-power source. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 30
    . Table 1-16 shows the power supply modules available for Catalyst 3750-X and 3560-X switches and power supply configurations based on switch models. Table 1-16 Switch Power Supply Modules Power Supply Module C3KX-PWR-1100WAC=2 48-Port PoE+ Switch1 24-Port PoE+ Switch Primary or spare Spare
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 31
    , see Chapter 3, "Power Supply and Fan Module Installation," and Appendix A, "Technical Specifications." XPS Connector Warning Attach only the following Cisco external power system to the switch: XPS 2200. Statement 387 The Cisco XPS 2200 is a expandable power system that can support nine network
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 32
    cable) The Cisco XPS 2200 has a nominal output level of -56 V. The total maximum output power depends on the installed power supply modules. The nine ports on the XPS 2200 provide the power and management signals to the Catalyst 3750-X and 3560-X switches. Other switch models do not support this
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 33
    port connection uses the supplied RJ-45-to-DB-9 Cisco Microsoft Windows USB Device Driver" section on page C-3 for installation instructions. When the switch detects a valid USB connection to a powered Cisco IOS commands. See the switch software configuration guide for details. OL-19593-02 Catalyst
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 34
    Cisco Network Assistant guide on Cisco guide and the device manager online help. • Cisco IOS troubleshooting of Cisco supports a comprehensive set of Management Information Base (MIB) extensions and four Remote Monitoring (RMON) groups. See the switch software configuration guide on Cisco guide on Cisco
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 35
    , page 2-22 • Installing SFP and SFP+ Modules, page 2-24 • Connecting Devices to the Ethernet Ports, page 2-26 • Where to Go Next, page 2-29 For initial switch setup, how to assign the switch IP address, and for powering information, see the switch getting started guide on Cisco.com. Preparing for
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 36
    one power supply connection. All connections must be removed to de-energize the unit. Statement 1028 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 2-2 OL
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 37
    power-supply module (C3KX-PWR-1100WAC=), first rack-mount the switch before installing the power-supply module. • Make sure power-supply modules and fan modules are securely inserted in the chassis before moving the switch. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 38
    devices can be up to 328 feet (100 meters). • For cable requirements for SFP+ module connections, see the "Cable and Adapter Specifications" section on page B-5. Each port must match the wave-length specifications on the other end of the cable, and the cable must not exceed the minimum cable length
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 39
    module is longer than the other modules. Stacking switches with the same power-supply modules together makes it easier to cable the switches. For switch dimensions, see Appendix A, "Technical Specifications." • Length of cable. Depending on the configurations that you have, you might need different
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 40
    supplied 0.5-meter StackWise cable. Both examples show full-ring configurations that provide redundant connections. Figure 2-2 Data Stacking the Catalyst 2 STACK 1 STACK 2 STACK 1 STACK 2 STACK 1 STACK 2 253201 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 2-6 OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 41
    STACK 2 STACK 1 STACK 2 2 Figure 2-6 and Figure 2-7 show data stacks of Catalyst 3750-X switches with failover conditions. In Figure 2-6, the StackWise cable is bad in 1 STACK 1 3 STACK 2 STACK 2 STACK 2 2 253204 OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 2-7
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 42
    the failure of a power supply, the StackPower mode becomes power sharing. Note Power-sharing mode is the recommended configuration for Catalyst 3750-X switches. The Catalyst 3560-X switches support only redundant mode. Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 2-8 OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 43
    the same power-supply modules together makes it easier to cable the switches. For switch dimensions, see Appendix A, "Technical Specifications." • supplied. If you need the 1.5 meter cable, you can order it from your Cisco supplier. For cable part numbers, see the "StackPower Connector (Catalyst
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 44
    -150CM Cable Type XPS 2200 connector cable XPS 2200 connector cable Figure 2-9 XPS 2200 Cable for Use with XPS 2200 Length 0.58 meter 1.5 meter 2-10 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 45
    You can configure a ring power stack or use the XPS 2200 to configure a star topology. Figure 2-10 shows a ring configuration using both of the supplied 0.3-meter StackPower cables and S-PWR S-PWR XPS AC OK PS OK OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 2-11
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 46
    2 Switch Installation Figure 2-11 shows nine switches connected to an XPS 2200 expandable power supply in a star topology. Figure 2-11 StackPower Star Topology Using the XPS 2200 OK PS OK C3KX-PWR-1100WAC 253397 2-12 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 47
    . You can configure multiple power stacks within a data stack, but a power stack that spans multiple data stacks is not supported. Figure 2-12 Power Stacking Catalyst 3750-X Switches within a C3K-PWR-715WAC 253398 OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 2-13
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 48
    into two stacks. The top two switches share power, and the bottom switch is now a separate Catalyst 3750-X-48 PoE switch as an example. You can install the Catalyst 3750-X and 3560-X switches following the same procedures. 2-14 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 49
    switch in a 19-inch rack, follow the instructions described in this section. Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take the mounting brackets and part numbers. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 2-15
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 50
    brackets 3 24-inch brackets 4 ETSI brackets 5 Extension rails and brackets for four-point mounting (includes 19-inch brackets) C3KX-RACK-KIT= C3KX-4PT-KIT= 2-16 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 51
    /TE1 G3 G4/TE2 1 Front-mounting position 2 Number-8 Phillips flat-head screws 3 Mid-mounting position 22 2 22 4 Rear-mounting position 5 Four-point mounting positions 253207 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 2-17
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 52
    the supplied Phillips machine screws to attach the brackets to the rack (Figure 2-18). Use the black Phillips machine screw to attach the cable guide to DUPLX PoE 7 4 C3KX-NM-10G NMEOTWDUOLREK Catalyst 3750-X PoE+48 G1 G2/TE1 G3 G4/TE2 253208 1 Phillips machine screw, black 2 Cable guide 3
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 53
    to enter the initial switch configuration. For instructions, see the switch getting started guide that shipped with the switch and also on Cisco.com. • Use the CLI setup program Ethernet Ports" section on page 2-26. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 2-19
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 54
    (Catalyst 3750-X Switches)" section on page 2-4. Always use a Cisco- lbf-in. (80 ozf-in.). Connect the other end of the cable to the connector on the other StackWise cable can shorten its useful life. Do not remove and insert Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 55
    end of the cable with the yellow stripe to another Catalyst 3750-X switch (to configure StackPower power sharing) or to an XPS 2200 power supply useful life. Do not remove and insert the cable more often than necessary. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 56
    Catalyst 3750-X Switches)" section on page 2-8. Always use a Cisco end of the cable with a red or yellow stripe to an XPS 2200 power supply can shorten its useful life. Do not remove There must be a supported network module in Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 57
    . For information about supported SFP modules, see the "SFP and SFP+ Modules" section on page 1-7. For more information about installing, removing, cabling, and troubleshooting network modules, see the module documentation on Cisco.com. For module cable specifications, see Appendix B, "Connector
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 58
    on Cisco.com for the list of SFP modules that the switch supports. Use only Cisco SFP modules on the switch. For more information about installing, removing, cabling, and troubleshooting SFP modules, see the module documentation that shipped with your device. For module cable specifications, see
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 59
    12 PoE+48 C3KX-NM-10G NMEOTWDUOLREK G1 G2/TE1 G3 G4/TE2 Step 5 Step 6 Step 7 If the module has a bale-clasp latch, close it to lock the SFP module in place. Remove the SFP dust plugs and save. Connect the SFP cables. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 60
    -X 47 48 PoE+48 G1 G2/TE1 G3 34 G4/TE2 1 Network module 2 SFP modules 3 Send (TX) optical bore 4 Receive (RX) optical bore 253157 Chapter 2 Switch Installation Removing an SFP Module Step 1 or other devices. 2-26 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 61
    both ends of the power supply modules required to support PoE and PoE+ on 24- and 48-port switches. To access a PoE planning tool, use the Cisco Power Calculator available on Cisco.com: http://tools.cisco.com/cpc/launch.jsp OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 62
    power supply requirements for a specific PoE configuration. Enter the number and types of powered devices that you plan to attach to the switch, and the calculator shows the PoE or PoE+ power required and the system power consumption. You must be a registered Cisco.com user to access the Cisco Power
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 63
    of a cluster or as an individual switch from the console. See the switch command reference on Cisco.com for information on using the CLI with the switch. • Start an SNMP application such as the CiscoView application. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 2-29
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 64
    Where to Go Next Chapter 2 Switch Installation 2-30 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 65
    software polls the device. After polling, the power supply module provides power to the switch, and the XPS 2200 is available to power other devices. Table 3-1 describes the supported internal power supply modules. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 3-1
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 66
    1. For full 15.4W support on a 48-port PoE+ switch, you must use a C3KX-PWR-1100WAC power supply module. Table 3-3 Switch Power Supply Requirements for PoE and PoE+ PoE Option 24-Port Switch PoE (up to 15.4 W per port) one 715-W power supply two 440-W DC power supplies PoE+ (up to 30 W per
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 67
    Figure 3-2 715-W AC Power Supply Module 1 23 4 AC OK PS OK C3KX-PWR-715WAC 253561 6 5 1 715-W AC power supply module 2 AC OK LED 3 PS OK LED 4 AC power cord connector 5 Release latch 6 Power cord retainer OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 3-3
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 68
    (negative polarity) 6 Grounding terminal 7 Release latch 8 Extraction handle 9 Terminal block safety cover If no power supply is installed in a power supply slot, install a power supply slot cover (Figure 3-5). 253562 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 3-4 OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 69
    with the module. • A power supply or fan module that is only partially connected to the switch can disrupt the system operation. • Remove power from the power-supply module before removing or installing the module. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 3-5
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 70
    available power budget, see the Catalyst 3750-X and 3560-X Software Configuration Guide. Caution Do not operate the switch with one power-supply module covers, and rear covers are in place. Statement 1029 • The switch supports hot swapping of a fan module. When replacing a fan, you should complete
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 71
    power cord to the power supply and to an AC power outlet. Turn on the power at the power source. Confirm that the power supply AC OK and PS OK LEDs are green. See Table 1-18 for a description of the power supply module LEDs. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 72
    Power Supply in the Switch, page 3-11 • Wiring the DC Input Power Source, page 3-11 Warning An exposed wire lead from a DC-input power on DC power terminals. Always replace cover when terminals are not in service. Be sure Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 3-8 OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 73
    power supply accessory kit. • Four leads of 14-gauge copper wire. • Four fork-type terminals from the DC power supply the grounding procedure instructions, and use a UL-listed lug (included in mm) 60528 Insulation Wire lead Step 3 Slide the open end of the ground lug over the exposed area of the
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 74
    Ground Lug Chapter 3 Power Supply and Fan Module Installation lug screws to 60 lbf-in. (960 ozf-in.). Connect the other end of the grounding wire to an appropriate grounding point at your site or to and dual-hole lug 3-10 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 75
    power wires from the power terminals. Press the release latch at the right side of the power supply module inward, and pull the power supply out. Insert the power supply in the power-supply slot in a grounded rack. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 3-11
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 76
    . Finding the Power Supply Module Serial Number If you contact Cisco Technical Assistance regarding a power supply module, you need to know the serial number. See Figure 3-14 to Figure 3-16 to find the serial number. 3-12 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 77
    1100-W AC Power Supply Serial Number SN: XXXNNNNXXXX 277563, 781-00669-01 C3KX-PWR-1100WAC Figure 3-15 715-W and 350-W AC Power Supply Module Serial Number SN: XXXNNNNXXXX 277561, 781-00668-01 C3KX-PWR-715WAC OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide 3-13
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 78
    and Fan Module Installation Figure 3-16 440-W DC Power Supply Module Serial Number SN: XXXNNNNXXXX 277562, 781-00667-01 C3KX-PWR 12 253565 4 1 Fan LED 2 Exhaust vent 3 3 Retainer clip 4 Extraction handles 3-14 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 79
    Power Supply and and firmly push the module) into the slot, applying pressure to the end of the module, not the extraction handles (Figure 3-18). When PWR-715WAC 253162 Finding the Fan Module Serial Number If you contact Cisco Technical Assistance regarding a fan module, you need to know the
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 80
    Finding the Fan Module Serial Number Figure 3-19 Fan Module Serial Number SN: XXXNNNNXXXX Chapter 3 Power Supply and Fan Module Installation 277564, 781-00666-01 3-16 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 81
    troubleshooting information about the switch. They show POST failures, port-connectivity problems, and overall switch performance. You can also get statistics from the device manager, the CLI, or an SNMP workstation. See the software configuration guide, the switch command reference guide on Cisco
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 82
    Diagnosing Problems Chapter 4 Troubleshooting Switch Connections Bad or Specifications" for more information. • Look for loose connections. Sometimes a cable appears to be seated but is not. Disconnect the cable and then reconnect it. Catalyst 3750-X and 3560-X Switch Hardware Installation Guide
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 83
    of your connected devices. See the "Power Supply Modules" section on page 1-19 for more information. • Verify the cable type. Many legacy powered devices, including older Cisco IP phones and access points that do not fully support IEEE 802.3af might not support PoE when connected to the switch by
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 84
    Link Detection (UDLD) on the switch to help identify unidirectional link problems. For information about enabling UDLD on the switch, see the "Understanding UDLD" section in the software configuration guide on Cisco.com. Switch Performance Speed, Duplex, and Autonegotiation Port statistics that show
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 85
    troubleshoot autonegotiation problems, try manually setting both sides of the connection. If this does not solve the problem, there could be a problem the "Cable and Adapter Specifications" section on page B-5. Resetting in the switch getting started guide on Cisco.com. You can also configure
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 86
    is powered off, and then connect it to the stack. If you had manually set the member numbers for the switch stack, manually assign the member number of the failed switch to the replacement switch. To manually assign the stack member number, see the switch software configuration guide on Cisco.com
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 87
    Storage altitude Physical Specifications Weight Catalyst 3750-X-12S Catalyst 3750-X-24S Catalyst 3750-X-24T Catalyst 3750-X-24P Catalyst 3750-X-48T Catalyst 3750-X-48P Catalyst 3750-X-48PF Catalyst 3560-X-24T Catalyst 3560-X-24P Catalyst 3560-X-48T Catalyst 3560-X-48P Catalyst 3560-X-48PF 32 to 113
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 88
    Power Supply Module Specifications Appendix A Technical Specifications Table A-1 Environmental and Physical Specifications (continued) Dimensions (H x W x D) Catalyst 3750-X-12S and 3750-X-24S Catalyst 3750-X and 3560-X-24T Catalyst 3750-X and 3560-X-24P Catalyst 3750-X and 3560-X-48T Catalyst
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 89
    or 8 AWG Branch circuit protection C3KX-PWR-440WDC: 20 A 1. The total input and total output BTU ratings refer to input power to the power supply and output power to the switch. The BTU ratings are based on -36 VDC. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide A-3
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 90
    Altitude Physical Specification Dimensions (H x D x W) Weight Operating Specification Airflow 23 to 113° F (-5 to 45° C) -40 to 158° F (-40 to 70° C) 10 to 95% (noncondensing) Up to 10,000 ft (3049 m) 1.68 x 6.8 x 5.74 in. (4.27 x 17.27 x 14.58 cm) 0.24 lb. (0.1 kg) 60 cfm Catalyst 3750-X and
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 91
    X Connector and Cable Specifications • "Connector Specifications" section on page B-1l • "Cable and Adapter Specifications" section on page B-5 Connector Specifications • 10/100/1000 Ports, page B-1 • 10 Gigabit Ethernet CX1 (SFP+ Copper) Connectors, page B-2 • SFP and SFP+ Modules, page B-2 • 10
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 92
    and Cable Specifications 10 Gigabit Ethernet CX1 (SFP+ Copper) SFP and SFP+ Modules Figure B-3, Figure B-4, and Figure B-5 show the SFP module connectors. The Catalyst 3560-X switch supports the SFP module patch cable, a 0.5-meter, copper, passive cable with SFP module connectors at each end
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 93
    Figure B-4 Simplex LC Cable Connector Connector Specifications 57834 Figure B-5 Pin 1 2 3 4 5 6 7 8 Copper SFP Module RJ-45 Connector Label 12345678 TP0+ TP0TP1+ TP2+ TP2TP1TP3+ TP3- Figure B-6 SFP Module Patch Cable (Catalyst 3560-X Switches) 60915 126809 10/100 Ethernet
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 94
    NC NC TDNC NC Appendix B Connector and Cable Specifications 12345678 H5318 Console Port The switch has two USB Type A-to-USB mini-Type B cable is not supplied. You can order an accessory kit (part number 800-33434 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide B-4 OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 95
    • Console Port Adapter Pinouts, page B-8 SFP and SFP+ Module Cable Specifications Each port must match the wave-length specifications on each end of the cable, and the cable must km) 43.4 to 62 miles (70 to 100 km)4 OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide B-5
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 96
    Specifications Appendix B Connector and Cable Specifications Table B-1 Fiber-Optic SFP and SFP+ Module Port Cabling Specifications (continued) SFP Module CWDM 10GBASE-LR (SFP TP13 TPO+ 6 TPO- 4 TP3+ 5 TP37 TP2+ 8 TP2- Catalyst 3750-X and 3560-X Switch Hardware Installation Guide B-6 OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 97
    Appendix B Connector and Cable Specifications Cable and Adapter Specifications Figure B-11 Switch 1 TP0+ 2 TP03 TP1+ 6 TP1- 4 TP2+ 5 TP27 TP3+ 8 TP3 -Pair Crossover Cable Schematic Switch 3 TD+ 6 TD- 1 RD+ 2 RD- H5579 OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide B-7
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 98
    Specifications Appendix B Connector and Cable Specifications Identifying a Crossover Cable To identify a crossover cable, hold the cable ends Table B-2 and Table B-3. Table B-2 lists the pinouts for the console port, the Catalyst 3750-X and 3560-X Switch Hardware Installation Guide B-8 OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 99
    and Adapter Specifications Table B-3 lists the pinouts for the console port, RJ-45-to-DB-25 female DTE adapter, and the console device. Note The RJ-45-to-DB-25 female DTE adapter is not supplied with the switch. You can order a kit with the adapter (part number ACS-DSBUASYN=) from Cisco. Table
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 100
    Cable and Adapter Specifications Appendix B Connector and Cable Specifications B-10 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 101
    provides a CLI-based setup procedure for a Catalyst 3750-X and 3560-X standalone switch or a switch stack. To set up the switch by using Express Setup, see the Cisco 3750-X and 3560-X Switch Getting Started Guide. Before connecting the switch to a power source, review the safety warnings in Chapter
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 102
    enter Cisco IOS commands and parameters through the CLI. Note If you have stacked Catalyst the 9-pin serial port on the PC. Connect the other end of the cable to the switch console port. Start the flow control) Connect power to the switch as described in Chapter 3, "Power Supply and Fan Module
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 103
    the USB console port on the switch. • Installing the Cisco Microsoft Windows XP USB Driver • Installing the Cisco Microsoft Windows 2000 USB Driver • Installing the Cisco Microsoft Windows Vista and Windows 7 USB Driver OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide C-3
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 104
    Windows Vista or Windows 7, double-click the setup(x64).exe file in the Windows_64 folder. The Cisco Virtual Com InstallShield Wizard begins. Click Next. The Ready to Install the Program window appears, Click Install. Catalyst 3750-X and 3560-X Switch Hardware Installation Guide C-4 OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 105
    instructions to complete the driver installation. Uninstalling the Cisco Microsoft Windows USB Driver • Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver • Uninstalling the Cisco appears click Finish. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide C-5
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 106
    program, which runs automatically after the switch is powered on. You must assign an IP address and information is also needed to use the device manager or Cisco Network Assistant to configure and manage the switch. IP Catalyst 3750-X and 3560-X Switch Hardware Installation Guide C-6 OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 107
    .0.0.0 Step 9 Enter Y to configure the switch as the cluster command switch. Enter N to configure it as a member switch or as a standalone switch. OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide C-7
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 108
    ! interface GigabitEthernet1/0/23 ! end Step 10 These choices appear: [0] Go to the IOS command prompt without saving this Cisco Network Assistant, the Cluster Management Suite (CMS), or another management tool for further configuration. Catalyst 3750-X and 3560-X Switch Hardware Installation Guide
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 109
    and 24-inch racks 2-18 A AC power power-supply module described 1-19 specifications A-3 adapter pinouts, terminal RJ-45-to-DB-25 B-9 RJ-45-to-DB-9 B-8 airflow patterns 1-21 altitude, operating and storage A-1 autonegotiation default setting 2-27 troubleshooting 4-4 B bodily injury protection warning
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 110
    1-23 crossover cable See cables D DC power power-supply module described 1-19 specifications A-3 DC power warning 3-8 device manager described 1-24 to configure switch 2-29 diagnosing problems 4-1 dimensions A-2 duplex default setting 2-27 LED 1-11 troubleshooting 4-4 E electrical noise, avoiding
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 111
    B-9 RJ-45-to-DB-9 terminal adapter B-8 SFP and SFP+ module ports B-2 straight-through cables four twisted-pair B-7 two twisted-pair B-7 PoE+ faults caution 1-13 LED 1-11, 1-15 port connections 2-27 ports described 1-5 OL-19593-02 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide IN-3
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 112
    management platforms 1-24 software switch management 1-24 specifications A-1 speed default setting 2-27 troubleshooting 4-4 stacking equipment warning 2-2 stacking powering considerations 2-8 StackWise ports 1-19 IN-4 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 113
    technical specifications A-1 telco racks 2-18 Telnet, and accessing the CLI 1-24 temperature, operating A-1 transceiver troubleshooting 4-3 troubleshooting bad or damaged cable 4-2 connection problems 4-2 diagnosing problems 4-1 Ethernet and fiber cables 4-2 link status 4-2 ping end device 4-4 PoE
  • Cisco WS-C3560X-48PF-L | Hardware Installation Guide - Page 114
    Index IN-6 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114

Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Catalyst 3750-X and 3560-X Switch
Hardware Installation Guide
June 2011
Text Part Number: OL-19593-02