Cisco WS-C3750X-24T-L Hardware Installation Guide - Page 33

Step 1, Starting Express Setup - sfp

Get Cisco WS-C3750X-24T-L PDF manuals and user guides View all Cisco WS-C3750X-24T-L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Chapter 1 Using Express Setup Starting Express Setup Follow these steps to start the Express Setup program: Step 1 Step 2 Verify that no devices are connected to the switch. Press and hold the Mode button, as shown in Figure 1-4, until the four LEDs above the Mode button turn green. This takes approximately 3 seconds. Figure 1-4 Starting Express Setup SYST RPS MASTR STAT DUPLX SPEED STACK MODE 97173 1 1 Mode button Step 3 Release the Mode button. Note If all of the LEDs begin to blink after you press the Mode button, release it. Blinking LEDs mean that the switch has already been configured and cannot go into Express Setup mode. For more information, see the "Clearing the Switch IP Address and Configuration" section on page 4-2. Step 4 Connect the Ethernet cable (not included) to a 10/100 Ethernet port or small form-factor pluggable (SFP) module port on the front panel of the switch, as shown in Figure 1-5. 78-15136-02 Catalyst 3750 Switch Hardware Installation Guide 1-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
1-5
Catalyst 3750 Switch Hardware Installation Guide
78-15136-02
Chapter 1
Using Express Setup
Starting Express Setup
Follow these steps to start the Express Setup program:
Step 1
Verify that no devices are connected to the switch.
Step 2
Press and hold the Mode button, as shown in
Figure 1-4
, until the four LEDs
above the Mode button turn green. This takes approximately 3 seconds.
Figure 1-4
Starting Express Setup
Step 3
Release the Mode button.
Note
If all of the LEDs begin to blink after you press the Mode button, release it.
Blinking LEDs mean that the switch has already been configured and cannot go
into Express Setup mode. For more information, see the
“
Clearing the Switch IP
Address and Configuration
”
section on page 4-2
.
Step 4
Connect the Ethernet cable (not included) to a 10/100 Ethernet port or small
form-factor pluggable (SFP) module port on the front panel of the switch, as
shown in
Figure 1-5
.
1
Mode button
SYST
RPS
MASTR
STAT
DUPLX
SPEED
STACK
MODE
97173
1