Compaq 6000 Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model
Compaq 6000 - ProLiant - 128 MB RAM Manual
UPC - 894582579463
View all Compaq 6000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Compaq 6000 manual content summary:
- Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 1
Hardware Reference Guide HP Compaq 6000 Pro Microtower Business PC - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 2
countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services -Packard Company. Hardware Reference Guide HP Compaq 6000 Pro Microtower Business PC First Edition (September 2009) Document Part Number: 576435-001 - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 3
About This Book This guide provides basic information for upgrading this computer model. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 4
iv About This Book ENWW - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 5
Rear Panel Components ...4 Keyboard ...5 Using the Windows Logo Key 6 Serial Number Location ...7 2 Hardware Upgrades Serviceability Features ...8 Warnings and Cautions ...8 Removing the Computer Access Panel 9 Replacing the Computer Access Panel 10 Removing the Front Bezel ...11 Removing Bezel - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 6
B Battery Replacement Appendix C External Security Devices Installing a Security Lock ...46 Cable Lock ...46 Padlock ...47 HP Business PC Security Lock 47 Front Bezel Security ...49 Appendix D Electrostatic Discharge Preventing Electrostatic Damage ...51 Grounding Methods ...51 Appendix E Computer - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 7
The HP Compaq Microtower features may vary depending on the model. For a complete listing of the hardware and software installed in the computer, run the diagnostic utility (included on some computer models only). Instructions for using the utility are provided in the Troubleshooting Guide. Figure - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 8
On Light is normally green when the power is on. If it is flashing red, there is a problem with the computer and it is displaying a diagnostic code. Refer to the Troubleshooting Guide to interpret the code. 1 Some models have bezel blanks covering one or both of the 5.25-inch drive bays. 2 Some - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 9
Slot Serial Bus) Port 6 CompactFlash I/II ● CompactFlash Card ● CompactFlash Card ● MicroDrive Type 1 Type 2 7 MS PRO/MS PRO DUO ● Memory Stick (MS) ● Memory Stick Select ● Memory Stick PRO ● MagicGate Memory Stick (MG) ● Memory Stick Duo (MS Duo) Duo (MS PRO Duo) ● Memory Stick PRO - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 10
VGA Monitor Connector 4 Serial Connector 9 DisplayPort Monitor Connector 5 RJ-45 Network Connector 10 Universal Serial Bus (USB) NOTE: Arrangement and number of connectors may vary by model. An optional second serial port and an optional parallel port are available from HP. When a device is - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 11
. 2 Editing Keys Includes the following: Insert, Home, Page Up, Delete, End, and Page Down. 3 Status Lights Indicate the status of the computer and keyboard settings (Num Lock, Caps Lock, and Scroll Lock). 4 Numeric Keys Work like a calculator keypad. 5 Arrow Keys Used to navigate through - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 12
Windows XP and Microsoft Windows Vista. Windows Logo Key Displays or hides the Start menu Windows Logo Key + d Displays the Desktop + l Locks the computer if you are connected to a network domain, or allows you to switch users if you are not connected to a network domain Windows Logo Key - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 13
Serial Number Location Each computer has a unique serial number and product ID number that are located on the top cover of the computer. Keep these numbers available for use when contacting customer service for assistance. Figure 1-3 Serial Number and Product ID Location ENWW Serial Number - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 14
describes proper workstation, setup, posture, and health and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located on the Web at http://www.hp.com/ergo. WARNING! Energized and moving parts inside. Disconnect power to the equipment - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 15
all removable media, such as compact discs or USB flash drives, from the computer. 3. Turn off the computer properly through the operating system, then turn off any external devices. 4. Disconnect the power cord from the power outlet and disconnect any external devices. CAUTION: Regardless of the - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 16
panel under the lip on the front of the chassis (1) then press the back end of the access panel onto the unit (2). Figure 2-2 Replacing the Computer Access Panel 2. Ensure that the panel is completely closed (1) and tighten the two thumbscrews that secure the access panel to the chassis (2). Figure - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 17
the system board as long as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage to the internal components of the computer. 5. Remove the computer access panel. 6. Lift up the three tabs on the side of the bezel (1), then rotate the bezel off the - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 18
chassis (1) then rotate the right side of the bezel onto the chassis (2) and snap it into place. Figure 2-6 Replacing the Front Bezel 12 Chapter 2 Hardware Upgrades ENWW - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 19
memory sockets are populated with at least one preinstalled DIMM. To achieve the maximum memory support, you can populate the system board with up to 16-GB of memory SPD information In addition, the computer supports: ● 512-Mbit, 1-Gbit, and 2-Gbit non-ECC memory technologies ● single-sided and - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 20
will display a POST error message indicating that a memory module one channel only. ● The system will operate in a higher-performing dual channel mode if the total memory capacity of the DIMMs in Channel A is equal to the total memory amount of memory describes the total amount of memory assigned to - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 21
devices. CAUTION: You must disconnect the power cord and wait approximately 30 seconds for the power to drain before adding or removing memory modules. Regardless of the power-on state, voltage is always supplied to the memory modules as long as the computer is plugged into an active AC outlet - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 22
access panel. 10. Reconnect the power cord and turn on the computer. 11. Lock any security devices that were disengaged when the access panel was removed. The computer should automatically recognize the additional memory the next time you turn on the computer. 16 Chapter 2 Hardware Upgrades ENWW - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 23
Expansion Card The computer has one PCI expansion slot, two PCI Express x1 expansion slots, and one PCI Express x16 expansion slot. Figure 2-9 Expansion Slot Locations Table 2-2 Expansion Slot Locations Item Description 1 PCI expansion slot 2 PCI Express x16 expansion slot 3 PCI Express x1 - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 24
PCI slot covers by lifting the green tab on the latch and rotating the latch to the open position. Figure 2-10 Opening the Expansion Slot Retainer 8. Before installing an expansion card, remove the expansion slot appropriate expansion slot cover on the back of the chassis. Pull the slot cover - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 25
to release it from the chassis frame. Be sure not to scrape the card against the other components. Figure 2-12 Removing a Standard PCI Expansion Card c. If you are removing a PCI Express x16 card, pull the retention arm on the back of the expansion socket away from the card and carefully rock the - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 26
slot cover to close the open slot. CAUTION: After removing an expansion card, you must replace it with a new card or expansion slot on the card is aligned with the open slot on the rear of the chassis. Press the expansion card slot. 12. Rotate the slot cover retention latch back in place - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 27
. 15. Reconnect the power cord and turn on the computer. 16. Lock any security devices that were disengaged when the access panel was removed. 17. Reconfigure the computer, if necessary. Refer to the Computer Setup (F10) Utility Guide for instructions on using Computer Setup. Drive Positions Figure - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 28
. Refer to the Computer Setup (F10) Utility Guide for more information. ● Connect a media card reader USB cable to the USB connector on the system board labeled MEDIA. If the media card reader has a 1394 port, connect the 1394 cable to the 1394 PCI card. ● The system does not support Parallel ATA - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 29
operating system properly, turn off the computer, and unplug the power cord. Do not remove a drive while the computer is on or in standby mode. a drive. Avoid exposing a hard drive to liquids, temperature extremes, or products that have magnetic fields such as monitors or speakers. If a drive must - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 30
The orange SATA3 connector can be reconfigured as eSATA in the Computer Setup utility if you are installing an eSATA adapter. Select Storage > Storage Options > eSATA Port to reconfigure the SATA3 connector. Refer to the Computer Setup (F10) Utility Guide for more information. 24 Chapter 2 Hardware - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 31
on the system board as long as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage to the internal components of the computer. 5. Remove the access panel and front bezel. 6. Disconnect the drive cables, as indicated in the following illustrations. a. If - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 32
a media card reader, disconnect the USB cable from the system board. If the media card reader has a 1394 port, disconnect the 1394 cable from the PCI card. Figure 2-20 Disconnecting the Media Card Reader USB Cable Figure 2-21 Disconnecting the Media Card Reader 1394 Cable 26 Chapter 2 Hardware - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 33
bracket (1) for the drive you want to remove, then slide the drive from its drive bay (2). Figure 2-22 Removing the External Drives 8. Remove the four guide screws (two on each side) from the old drive. You will need these screws to install a new drive. ENWW Installing and Removing Drives 27 - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 34
an active AC outlet. You must disconnect the power cord to avoid damage to the internal components of the computer. 5. If you are installing a drive in Install four M3 metric guide screws in the lower holes on each side of the drive. HP has provided eight extra M3 metric guide screws on the front - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 35
8. Slide the drive into the drive bay, making sure to align the guide screws with the guide slots, until the drive snaps into place. Figure 2-24 Sliding the External Drives into the Drive Cage 9. Connect the power and data cables to the drive as indicated in the following illustrations. a. If you - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 36
the USB cable to the system board. If the media card reader has a 1394 port, connect the 1394 cable to the PCI card. Figure 2-26 Connecting the Media Card Reader USB Cable Figure 2-27 Connecting connectors. 11. Replace the front bezel and computer access panel. 30 Chapter 2 Hardware Upgrades ENWW - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 37
12. Reconnect the power cord and any external devices, then turn on the computer. 13. Lock any security devices that were disengaged when the access panel was removed. ENWW Installing and Removing Drives 31 - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 38
computer. 3. Turn off the computer properly through the operating system, then turn off any external devices. 4. Disconnect the power cord from the power disconnect the power cord to avoid damage to the internal components of the computer. 5. Remove the access panel. 6. Disconnect the power cable (1) - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 39
by pulling the release tab away from the drive (1) and sliding the drive out of the bay (2). Figure 2-29 Removing a Hard Drive 8. Remove the four guide screws (two on each side) from the old drive. You will need these screws to install a new drive. ENWW Installing and Removing Drives 33 - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 40
board as long as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage to the internal components of the computer. 5. Remove the access panel. 6. Install the four guide screws (two on each side) that were removed from the old drive into the new drive - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 41
guide screws with the guide slots, until the drive snaps into place. The bottom bay is for the primary hard drive. The upper bay is for an optional secondary hard drive. Figure 2-31 Sliding a Hard Drive into the Drive Bay 8. Connect the power has only one SATA hard drive performance problems. If - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 42
12. Reconnect the power cord and any external devices, then turn on the computer. 13. Lock any security devices that were disengaged when the access panel was removed. Removing and slide the top cover off the carrier (2). Figure 2-33 Removing the Carrier Cover 36 Chapter 2 Hardware Upgrades ENWW - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 43
3. Remove the adhesive strip that secures the thermal sensor to the top of the hard drive (1) and move the thermal sensor away from the carrier (2). Figure 2-34 Removing the Thermal Sensor 4. Remove the four screws from the bottom of the hard drive carrier. Figure 2-35 Removing the Security Screws - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 44
the hard drive is pressed all the way into the connector on the carrier's circuit board. Figure 2-37 Replacing the Hard Drive 38 Chapter 2 Hardware Upgrades ENWW - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 45
7. Replace the four screws in the bottom of the carrier to hold the drive securely in place. Figure 2-38 Replacing the Security Screws 8. Place the thermal sensor on top of the hard drive in a position that does not cover the label (1) and attach the thermal sensor to the top of the hard drive with - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 46
the carrier to secure the cover in place (2). Figure 2-40 Replacing the Carrier Cover 10. Slide the hard drive carrier into the enclosure on the computer and lock it with the key provided. NOTE: The carrier must be locked for power to be supplied to the hard drive. 40 Chapter 2 Hardware - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 47
Specifications Desktop Dimensions C/Hr. The upper limit may be limited by the type and number of options installed. Heat Dissipation Max STD PS 1410 BTU/hr 356 20/50/100% load PS idle 95 BTU/hr 24 kg-cal/hr Power Supply 115V 230V Operating Voltage Range (STD PS)1 90-264 VAC 90-264 VAC - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 48
115 VAC 2.75A @ 230 VAC 1 This system utilizes an active power factor corrected power supply. This allows the system to pass the CE mark requirements for use in the countries of the European Union. The active power factor corrected power supply also has the added benefit of not requiring an input - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 49
only with the HP spare designated for this product. CAUTION: Before replacing the battery, it is important to back up the computer CMOS settings. When the battery is removed or replaced, the CMOS settings will be cleared. Refer to the Computer Setup (F10) Utility Guide for information on backing - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 50
NOTE: On some computer models, it may be necessary to remove an internal component to gain access to the battery. 7. Depending on the type of battery holder on the system board, complete the following instructions to replace the battery. Type 1 a. Lift the battery out of its holder. Figure B-1 - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 51
the clip back into place. Figure B-3 Removing a Coin Cell Battery (Type 3) NOTE: After the battery has been replaced, use the following steps to complete this procedure. 8. Replace the computer access panel. 9. Plug in the computer and turn on power to the computer. 10. Reset the date and time, your - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 52
For information on data security features, refer to the Computer Setup (F10) Utility Guide, the Desktop Management Guide, and the HP ProtectTools Security Manager Guide (some models) at http://www.hp.com. Installing a Security Lock The security locks displayed below and on the following pages can be - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 53
Padlock Figure C-2 Installing a Padlock HP Business PC Security Lock 1. Fasten the security cable by looping it around a stationary object. Figure C-3 Securing the Cable to a Fixed Object ENWW Installing a Security Lock 47 - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 54
2. Thread the keyboard and mouse cables through the lock. Figure C-4 Threading the Keyboard and Mouse Cables 3. Screw the lock to the chassis using the screw provided. Figure C-5 Attaching the Lock to the Chassis 48 Appendix C External Security Devices ENWW - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 55
screw provided by HP. To install the security screw: 1. Remove/disengage any security devices that prohibit opening the computer. 2. Remove all computer. 3. Turn off the computer properly through the operating system, then turn off any external devices. 4. Disconnect the power cord from the power - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 56
hard drive bay and speaker. Figure C-8 Installing the Front Bezel Security Screw 9. Replace the access panel. 10. Reconnect the power cord and turn on the computer. 11. Lock any security devices that were disengaged when the access panel was removed. 50 Appendix C External Security Devices ENWW - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 57
Grounding Methods There are several methods for grounding. Use one or more of the following methods when handling or installing electrostatic-sensitive parts: ● Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis. Wrist straps are flexible straps with a minimum - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 58
feet down, directly against the front of the desktop unit as this also restricts airflow. ● Never operate the computer with the access panel or any of the expansion card slot covers removed. ● Do not stack computers on top of each other or place computers so near each other that they are subject to - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 59
changes while the drive is on, wait at least one hour before you turn off the power. If you operate the unit immediately, it may malfunction the computer and have it checked by an authorized HP service provider. Shipping Preparation Follow these suggestions when preparing to ship the computer: 1. - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 60
connector DisplayPort 4 VGA 4 mouse connector 4 N network connector 4 O optical drive cleaning 53 installing 28 precautions 53 removing 25 P PCI card 17, 19 PCI Express card 17, 19 power supply 41 product ID location 7 R rear panel components 4 removable hard drive replacing 36 removing battery 43 - Compaq 6000 | Hardware Reference Guide - HP Compaq 6000 Pro Microtower Model - Page 61
25 PCI card 19 PCI Express card 19 S security cable lock 46 front bezel 49 HP Business PC Security Lock 47 padlock 47 serial connector 4 serial number location 7 shipping preparation 53 specifications computer 41 memory 13 system board drive connections 24 U unlocking access panel 46 USB ports front
Hardware Reference Guide
HP Compaq 6000 Pro Microtower Business PC