Compaq DS-DSGGC-AB Installation Guide

Compaq DS-DSGGC-AB - StorageWorks Fibre Channel SAN Switch 16-EL Manual

Get Compaq DS-DSGGC-AB - StorageWorks Fibre Channel SAN Switch 16-EL PDF manuals and user guides View all Compaq DS-DSGGC-AB manuals
Add to My Manuals
Save this manual to your list of manuals

Compaq DS-DSGGC-AB manual content summary:

  • Compaq DS-DSGGC-AB | Installation Guide - Page 1
    installation guide hp StorageWorks SAN switch 2/16 version 3.1.x Product Version: 3.1.x Third Edition (June 2003) Part Number: AA-RR84C-TE This installation guide provides basic procedures for setting up, configuring, and managing the SAN Switch 2/16 and SAN Switch 2/16 power pak models.
  • Compaq DS-DSGGC-AB | Installation Guide - Page 2
    express limited warranty statements for such products. Nothing herein should be construed as constituting an additional warranty. Printed in the U.S.A. SAN Switch 2/16 Version 3.1.x Installation Guide Third Edition (June 2003) Part Number: AA-RR84C-TE
  • Compaq DS-DSGGC-AB | Installation Guide - Page 3
    contents Contents About this Guide 9 Overview 10 Intended Audience 10 Related Documentation 10 Conventions 11 Document Conventions 11 Text Symbols 11 Equipment Symbols 12 Rack Stability 14 Getting Help 15 HP Technical Support 15 HP Storage Website 15 HP Authorized Reseller 16 1 Overview
  • Compaq DS-DSGGC-AB | Installation Guide - Page 4
    Policies 66 Connecting the Switch to the Fabric 66 Verifying Operation 67 Installing Multiple Switches into an Existing SAN 68 4 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 5
    92 Spécification ATI Classe A (France 92 Germany Noise Declaration 92 VCCI EMC Statement (Japan 92 Harmonics Conformance (Japan 93 SAN Switch 2/16 Version 3.1.x Installation Guide 5
  • Compaq DS-DSGGC-AB | Installation Guide - Page 6
    19 Assembling the inner rails 53 20 Installing the switch into a rack (HP 9000 Series or comparable EIA rack 54 6 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 7
    Normal Operation 76 6 Physical Specifications 100 7 Power Supply Specifications 101 8 Environmental Requirements 102 9 Cabling Pinouts if Pin 7 is Used 103 SAN Switch 2/16 Version 3.1.x Installation Guide 7
  • Compaq DS-DSGGC-AB | Installation Guide - Page 8
    Contents 8 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 9
    guAidbe porouvitdetshinisforGmautioindtoehelp you set up and configure the HP StorageWorks SAN Switch 2/16. About this Guide About this Guide topics include: ■ Overview, page 10 ■ Conventions, page 11 ■ Rack Stability, page 14 ■ Getting Help, page 15 SAN Switch 2/16 Version 3.1.x Installation
  • Compaq DS-DSGGC-AB | Installation Guide - Page 10
    About this Guide Overview This section covers the following topics: ■ Intended Audience ■ Related Documentation Intended Audience This book is intended for use by customers who purchased the SAN Switch 2/16, 2/16 power pak; and for authorized service providers who are experienced with the following:
  • Compaq DS-DSGGC-AB | Installation Guide - Page 11
    Blue, underlined sans serif font text, for example: http://www.hp.com Text Symbols The following symbols may be found in the text of this guide. They have the following meanings. WARNING: Text set off in this manner indicates that failure to follow directions in the warning could result in bodily
  • Compaq DS-DSGGC-AB | Installation Guide - Page 12
    following equipment symbols may be found on hardware for which this guide pertains. They have the following meanings. Any enclosed surface or the presence of electrical shock hazards. Enclosed area contains no operator serviceable parts. WARNING: To reduce the risk of personal injury from electrical
  • Compaq DS-DSGGC-AB | Installation Guide - Page 13
    About this Guide Power supplies or systems marked with these symbols indicate the presence of multiple sources of or damage to the equipment, observe local occupational health and safety requirements and guidelines for manually handling material. SAN Switch 2/16 Version 3.1.x Installation Guide 13
  • Compaq DS-DSGGC-AB | Installation Guide - Page 14
    About this Guide Rack Stability Rack stability protects personnel and equipment. WARNING: To reduce the risk of personal injury or damage to the equipment, be A rack may become unstable if more than one rack component is extended for any reason. 14 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 15
    Help If you still have a question after reading this guide, contact an HP authorized service provider or access our website: http://www.hp.com. HP Technical Support In North America, call technical support at 1-800-652-6672, available 24 hours a day, 7 days a week. Note: For continuous quality
  • Compaq DS-DSGGC-AB | Installation Guide - Page 16
    About this Guide HP Authorized Reseller For the name of your nearest HP authorized reseller: ■ In the United States, call 1-800-345-1518. ■ In Canada, 263-5868. ■ Elsewhere, see the HP website for locations and telephone numbers: http://www.hp.com 16 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 17
    HP StorageWorks SAN Switch 2/16 Version 3.1.x Release Notes for a complete list of management features enabled on your specific switch. Note: This guide refers to both models as the SAN Switch 2/16, unless otherwise noted. This chapter provides the following information: ■ SAN Switch 2/16 Features
  • Compaq DS-DSGGC-AB | Installation Guide - Page 18
    a protocol that allows applications to interface with switch services. ■ Zoning, providing a means to allocate storage User Guide. ■ Per port statistics to help technicians diagnose and isolate problem ports when the problem is resolved. ■ Industry standard Management Information Base (MIB) support. ■
  • Compaq DS-DSGGC-AB | Installation Guide - Page 19
    that processes frames up to 1,024 bytes. ■ A real-time clock (RTC) with a 10-year battery and 56 bytes of NVRAM. SAN Switch 2/16 Version 3.1.x Installation Guide 19
  • Compaq DS-DSGGC-AB | Installation Guide - Page 20
    running v2.6x and above, building a highly scalable SAN fabric. The Fibre Channel SAN Switch 2/16 supports F_port, FL_port, and E_port connections and Distributed Name Server (DNS). The ports on the front panel for Fibre Channel SFP transceivers. 20 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 21
    about ISL trunking, refer to the HP StorageWorks Trunking Version 3.1.x/4.1.x User Guide. SFPs The ports connect to SFP media. SFPs are universal and and no jumpers or hardware settings. Replacement instructions are provided with all replacement units ordered. SAN Switch 2/16 Version
  • Compaq DS-DSGGC-AB | Installation Guide - Page 22
    Overview Optional Hardware Kits HP provides the following optional hardware kits in support of the SAN Switch 2/16, see Table 2. Table 2: SAN B23** 221691-B26** 221691-B27** C7534A* C7534A* * premerger HP part number ** premerger Compaq part number 22 SAN Switch 2/16 Version 3.1.x Installation
  • Compaq DS-DSGGC-AB | Installation Guide - Page 23
    the Switch to the Fabric, page 66 ■ Installing Multiple Switches into an Existing SAN, page 68 ■ Next Steps, page 69 SAN Switch 2/16 Version 3.1.x Installation Guide 23
  • Compaq DS-DSGGC-AB | Installation Guide - Page 24
    in Figure 3 and Table 3 may not represent the kit that shipped with your switch. HP reserves the right to substitute Rack Mount Kits, providing applicable instructions with each switch. 24 SAN Switch 2/16 Version 3.1.x Installation
  • Compaq DS-DSGGC-AB | Installation Guide - Page 25
    Installing the SAN Switch 2/16 2 3 1 5 4 6 Figure 3: Carton contents SHR-2489A SAN Switch 2/16 Version 3.1.x Installation Guide 25
  • Compaq DS-DSGGC-AB | Installation Guide - Page 26
    Fixed Rack Mount Kit items listed in Table 3 may not represent the rail kit that shipped with your switch. 26 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 27
    (or comparable) Rack using the Rack Mount Kit supplied with the switch, contents as outlined in Table 3. For instructions, see Installing the SAN Switch 2/16 in an HP 9000 Series or Comparable EIA Rack, page 31. ■ circuit, such as a power strip. SAN Switch 2/16 Version 3.1.x Installation Guide 27
  • Compaq DS-DSGGC-AB | Installation Guide - Page 28
    voltage jumpers or switches. The power supply is auto ranging in terms of accommodating input voltages and line frequencies. 28 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 29
    . ■ Avoid touching pins, leads, or circuitry. ■ Always make sure you are properly grounded when touching a static-sensitive component or assembly. SAN Switch 2/16 Version 3.1.x Installation Guide 29
  • Compaq DS-DSGGC-AB | Installation Guide - Page 30
    , repeat steps 3 through 5 for the remaining power supply. Note: Do not connect the switch to the network until the IP address is correctly set. For instructions on how to set the IP address, see "Configuring Network Addressing" later in this chapter. 30 SAN Switch 2/16 Version 3.1.x Installation
  • Compaq DS-DSGGC-AB | Installation Guide - Page 31
    inner slide rail attached to an outer slide rail. Read the following sections for complete instructions on first separating, then installing the slide rail assemblies. Separating the Inner Slide Rail Assembly the Inner Slide Rails to the Switch." SAN Switch 2/16 Version 3.1.x Installation Guide 31
  • Compaq DS-DSGGC-AB | Installation Guide - Page 32
    x 3/16-inch screws provided in the Rack Mount Kit. Secure the inner slide rail to the switch, see Figure 4. 32 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 33
    exhaust air is released. Air intake and exhaust for all components in the rack should flow in the same direction.) SAN Switch 2/16 Version 3.1.x Installation Guide 33
  • Compaq DS-DSGGC-AB | Installation Guide - Page 34
    pounds. 4. Repeat steps 1 through 3 to install the left mount bracket on the left side of the switch, see Figure 5. 34 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 35
    Kit: ■ Four 3-hole bar nuts ■ Eight Phillips head 8-32 x 3/8-inch screws ■ Eight square alignment washers ■ # 2 Phillips screwdriver with torque capability SAN Switch 2/16 Version 3.1.x Installation Guide 35
  • Compaq DS-DSGGC-AB | Installation Guide - Page 36
    bar nut between the rack's rail and the L-bracket at the end of the outer slide rail, see Figure 6. 36 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 37
    . [7] Select Import. Position the illustration as required. 2 [8] Adjust the size of the outer graphic frame as required. Delete this set of instructions 1 5 1 Phillips head 10-32 x 3/8-inch screw 2 3-hole bar nut 3 Outer slide rail SHR-2478A 4 L-Brackets 5 Power cord clip (1 of 6) Figure
  • Compaq DS-DSGGC-AB | Installation Guide - Page 38
    the inner slide rails (attached to the switch) into the outer slide rails (attached to the rack), see Figure 7. 38 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 39
    rack mount bracket to the rack rails. 3. Tighten the screws, and torque to 25-inch pounds. 4. See the "Connecting AC Power" on page 56 for instructions on applying power to the switch. SAN Switch 2/16 Version 3.1.x Installation
  • Compaq DS-DSGGC-AB | Installation Guide - Page 40
    SAN Switch 2/16 Installing the Switch in the Optional HP System/e Rack This section provides instructions for installing the switch in the HP System/e rack. Items Required for the HP lock washers (2) Rubber washers (4) M5 U-type Tinnerman clips 40 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 41
    brackets with one M5 Torx head screw with captive lock washers as shown in Figure 8. Figure 8: Installing the mounting brackets SAN Switch 2/16 Version 3.1.x Installation Guide 41
  • Compaq DS-DSGGC-AB | Installation Guide - Page 42
    portion of the outer rail flush against the rear rail-tray brackets. Install them as shown in Figure 10. 42 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 43
    the illustration as required. [8] Adjust the size of the outer graphic frame as required. Delete this set of instructions 1 2 1 Rubber washer (1 of 2) 2 Rear rail tray bracket (1 of 2) Figure 10: Installing the lower right screws until later. SAN Switch 2/16 Version 3.1.x Installation Guide 43
  • Compaq DS-DSGGC-AB | Installation Guide - Page 44
    x 5/16 Phillips pan-head screws, and #8 flat washer as shown in Figure 12. Figure 12: Assembling the inner rails 44 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 45
    . See Figure 13. Figure 13: Installing switch into the HP rack SHR-2583 10. See the next section, "Connecting AC Power" on page 56, for instructions on applying power to the switch. SAN Switch 2/16 Version 3.1.x Installation
  • Compaq DS-DSGGC-AB | Installation Guide - Page 46
    16 Installing the Switch Using the HP StorageWorks SAN Switch Universal Rack Mount Kit This section provides instructions for installing the SAN Switch 2/16 in an HP rack using the Universal Rack Mount Kit, head screw with captive star lock washer 46 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 47
    carton to verify all the required parts and hardware are available. 2. Choose a mounting location in the rack for the switch. SAN Switch 2/16 Version 3.1.x Installation Guide 47
  • Compaq DS-DSGGC-AB | Installation Guide - Page 48
    as shown in Figure 14. Figure 14: Installing the rear mounting brackets (HP 9000 Series or comparable EIA rack) 48 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 49
    alignment washers as shown in Figure 15. Figure 15: Installing the rear mounting brackets (HP System/e rack-left rear upright) SAN Switch 2/16 Version 3.1.x Installation Guide 49
  • Compaq DS-DSGGC-AB | Installation Guide - Page 50
    will be tightened later in step 8. Figure 16: Installing the outer rails (HP 9000 Series or comparable EIA rack) 50 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 51
    of the left rail. See Figure 17. Figure 17: Assembling the outer rails (HP 9000 Series or comparable EIA rack) SAN Switch 2/16 Version 3.1.x Installation Guide 51
  • Compaq DS-DSGGC-AB | Installation Guide - Page 52
    lower hole locations of the left rail. See Figure 18. Figure 18: Assembling the outer rails (HP System/e rack) 52 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 53
    the SAN Switch 2/16 with five screws. Attaching both inner rails requires ten screws. Figure 19: Assembling the inner rails SAN Switch 2/16 Version 3.1.x Installation Guide 53
  • Compaq DS-DSGGC-AB | Installation Guide - Page 54
    Figure 20 and Figure 21. Figure 20: Installing the switch into a rack (HP 9000 Series or comparable EIA rack) 54 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 55
    middle #10-32 x 1/2-inch Phillips pan head screw with captive star lock washer from either side of the rack uprights. SAN Switch 2/16 Version 3.1.x Installation Guide 55
  • Compaq DS-DSGGC-AB | Installation Guide - Page 56
    the clips can be on either side of the rail, provided all the tabs are on the same side. 56 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 57
    Do not connect the switch to the network until the IP address is correctly set. For instructions on setting the IP address, see "Configuring Network Addressing," on page 58. Power-On Self HP StorageWorks Fabric OS Version 3.1x/4.1x Procedures User Guide. SAN Switch 2/16 Version 3.1.x Installation
  • Compaq DS-DSGGC-AB | Installation Guide - Page 58
    (CLI) using the errShow command. For more information about error messages, refer to the HP StorageWorks Fabric OS Version 3.1.x/4.1.x Reference Guide. Configuring Network Addressing Read the following sections for information on how to configure addressing for the switch. Requirements The following
  • Compaq DS-DSGGC-AB | Installation Guide - Page 59
    in this chapter. 5. Power on the workstation and establish a connection to the switch using a terminal emulator application (such as HyperTerminal). SAN Switch 2/16 Version 3.1.x Installation Guide 59
  • Compaq DS-DSGGC-AB | Installation Guide - Page 60
    Installing the SAN Switch 2/16 Note: These steps show instructions specific to HyperTerminal. If using a different application, consult the specific application's documentation. 6. Using [y = set now, n = next reboot]: Enter "y" to set now. 60 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 61
    shipping plug in the Serial port. Caution: The Serial port is intended only for use during the initial setting of the IP address and for service purposes. Using the Serial port during normal switch operation or for regular maintenance is not recommended. 8. Record the IP address on the label affixed
  • Compaq DS-DSGGC-AB | Installation Guide - Page 62
    the switch with administrative privileges by telnet. The default administrative logon is admin and the default password is password. 62 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 63
    : [1 or 0] Note: In the above example, the Core PID format is 1 or 0, depending on the number displayed in the brackets. SAN Switch 2/16 Version 3.1.x Installation Guide 63
  • Compaq DS-DSGGC-AB | Installation Guide - Page 64
    switches in the fabric, go to the "Connecting the Switch to the LAN" section on page 62 for instructions on connecting Fibre Channel cables. 11. If necessary, type cfgEnable to re-establish zoning. Note: Once the subsequent firmware upgrades. 64 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 65
    CTRL+D to accept the remaining settings without completing all the prompts). 6. Re-enable the switch by entering the following: switchEnable SAN Switch 2/16 Version 3.1.x Installation Guide 65
  • Compaq DS-DSGGC-AB | Installation Guide - Page 66
    cables used in trunking groups must meet specific requirements. For a list of these requirements, refer to the HP StorageWorks ISL Trunking Version 3.1.x/4.1.x User Guide. 1. Remove the shipping plug from the appropriate ports. 2. Position the SFP so that the key (the tab near the cable-end of the
  • Compaq DS-DSGGC-AB | Installation Guide - Page 67
    switch IP address. 3. If connected properly, the name of your switch appears (in green) at the prompt, indicating Healthy/OK. SAN Switch 2/16 Version 3.1.x Installation Guide 67
  • Compaq DS-DSGGC-AB | Installation Guide - Page 68
    This ensures that a complete configuration is available if required for a replacement switch. For instructions on how to back up the configuration, refer to "Backing Up System Configuration Settings through a workstation and to set the IP address. 68 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 69
    occurs, the switch must be taken offline for repair or replacement. Contact your HP Technical Support for assistance. 5. Power off the new switch and connect one Fibre Channel cable from speed level. Auto negotiation may not be supported by the SAN Switch 2/16 Version 3.1.x Installation Guide 69
  • Compaq DS-DSGGC-AB | Installation Guide - Page 70
    the configuration information for your network components for specific requirements. See the HP StorageWorks Fabric OS Version 3.1.x/4.1.x Procedures User Guide for a detailed command description. Cascading Switches The Domain ID number uniquely identifies a switch in a fabric. Normally, the switch
  • Compaq DS-DSGGC-AB | Installation Guide - Page 71
    Managing the SAN Switch 2/16 3 This chapter covers the following topics: ■ Interpreting LED Activity, page 72 ■ Management Overview, page 78 ■ Running Basic Switch Operations Using Telnet, page 79 ■ Diagnostic Tests, page 84 SAN Switch 2/16 Version 3.1.x Installation Guide 71
  • Compaq DS-DSGGC-AB | Installation Guide - Page 72
    diagnostic tests are running. This is normal, and does not indicate a problem. Note: Any errors related to LED activity are listed in the error error log, refer to the HP StorageWorks Fabric OS Version 3.1.x/4.1.x Procedures Guide. Front Panel LEDs The front panel includes the following LEDs: ■
  • Compaq DS-DSGGC-AB | Installation Guide - Page 73
    to port. No action required. No action required. No action required. No action required. Reset the switch from a management station. SAN Switch 2/16 Version 3.1.x Installation Guide 73
  • Compaq DS-DSGGC-AB | Installation Guide - Page 74
    Action Reset the switch from a management station. Reset the port from a management station. No action required. No action required. 74 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 75
    light, contact the switch supplier. No action required. Errors may be listed in the error log. Refer to the HP StorageWorks Fabric OS Version 3.1.x/4.1.x Procedures Guide for more information. SAN Switch 2/16 Version 3.1.x Installation
  • Compaq DS-DSGGC-AB | Installation Guide - Page 76
    switch is on and boot had time to complete. If there is still no light, contact the switch supplier. 76 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 77
    yellow Diagnostic failure on one or more ports. Errors may be listed in the error log. Refer to the HP StorageWorks Fabric OS Version 3.1.x/4.1.x Procedures Guide for more information. SAN Switch 2/16 Version 3.1.x Installation
  • Compaq DS-DSGGC-AB | Installation Guide - Page 78
    virtually in front of any fabric, switch, or port. For more information refer to the HP StorageWorks Web Tools Version 3.1.x/4.1.x User Guide. Optional Management Features Refer to the HP StorageWorks SAN Switch 2/16 Version 3.1.x Release Notes for a complete list of management features enabled
  • Compaq DS-DSGGC-AB | Installation Guide - Page 79
    a telnet connection to the switch. The login prompt displays if the telnet connection successfully found the switch in the network. SAN Switch 2/16 Version 3.1.x Installation Guide 79
  • Compaq DS-DSGGC-AB | Installation Guide - Page 80
    the New Password prompt, enter the new password. The new password must be from 8 to 40 characters in length. 80 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 81
    active now or at the next reboot. Enter y at the prompt to have the IP address changes take effect immediately. SAN Switch 2/16 Version 3.1.x Installation Guide 81
  • Compaq DS-DSGGC-AB | Installation Guide - Page 82
    00-23. - mm is minutes, valid values are 00-59. - YY is the year, valid values are 00-99. 82 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 83
    year values less than 70 are interpreted as 2000-2069. The date function does not support daylight saving time or time zones. Displaying Switch Configuration Settings Use these steps to display the The system configuration settings are displayed. SAN Switch 2/16 Version 3.1.x Installation Guide 83
  • Compaq DS-DSGGC-AB | Installation Guide - Page 84
    to beacon, refer to the HP StorageWorks Fabric OS Procedures Version 3.1.x/4.1.x User Guide. Note: If the switch prompt does not display when POST completes, Procedures Version 3.1.x/4.1.x User Guide. Diagnostic Tests Diagnostic tests are provided to help troubleshoot the hardware and the firmware
  • Compaq DS-DSGGC-AB | Installation Guide - Page 85
    Configuration Settings, page 86 ■ Upgrading or Restoring the Switch Firmware, page 88 ■ Downloading Firmware from the HP Website, page 89 SAN Switch 2/16 Version 3.1.x Installation Guide 85
  • Compaq DS-DSGGC-AB | Installation Guide - Page 86
    before an upload can occur. Use the RSHD service or FTP on a UNIX machine. Note: The two supplied utilities, RSHD.EXE and CAT.EXE, currently do not support uploads for Windows, only downloads. These utilities [rshd]: ftp Password: upload complete 86 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 87
    system configuration settings from a backup. 1. Verify that the RSHD service (on a UNIX machine) or the FTP service (on a Windows or UNIX machine) is running on the host workstation. 2. Log into the switch entering the following command: fastBoot SAN Switch 2/16 Version 3.1.x Installation Guide 87
  • Compaq DS-DSGGC-AB | Installation Guide - Page 88
    steps to upgrade or restore the switch firmware. 1. Verify that the RSHD service (on a UNIX machine) or the FTP service (on a Windows or UNIX machine) is running on the host workstation. 2. Log into the switch as the following command: fastBoot 88 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 89
    from the HP Website To download the firmware from the HP website, go to http://www.hp.com. The website contains the required loaders and instructions for downloading the firmware to a switch. SAN Switch 2/16 Version 3.1.x Installation
  • Compaq DS-DSGGC-AB | Installation Guide - Page 90
    Backing Up the Configuration and Upgrading Firmware 90 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 91
    radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a the user's authority to operate the equipment. SAN Switch 2/16 Version 3.1.x Installation Guide 91
  • Compaq DS-DSGGC-AB | Installation Guide - Page 92
    .1 dB(A)Am Arbeitsplatz (operator position) Normaler Betrieb (normal operation)Nach ISO 7779:1999 (Typprüfung) VCCI EMC Statement (Japan) 92 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 93
    Harmonics Conformance (Japan) BSMI EMC Statement (Taiwan) Regulatory Compliance Notices RRL EMC Statement (Korea) SAN Switch 2/16 Version 3.1.x Installation Guide 93
  • Compaq DS-DSGGC-AB | Installation Guide - Page 94
    is certified as a Class 1 Laser product, conforming to the requirements contained in Department Of Health and Human Services (DHHS) regulation 21 CFR, Subchapter J. The certification is indicated by a label on the metal SFP the IEC and U.S. DHHS. 94 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 95
    battery is incorrectly replaced or mistreated. Replacement is to be done by an HP authorized service provider using the HP spare designated for this product. For more information about battery replacement or HP partners, or their agents. SAN Switch 2/16 Version 3.1.x Installation Guide 95
  • Compaq DS-DSGGC-AB | Installation Guide - Page 96
    Regulatory Compliance Notices 96 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 97
    . ■ Avoid touching pins, leads, or circuitry. ■ Always make sure you are properly grounded when touching a static-sensitive component or assembly. SAN Switch 2/16 Version 3.1.x Installation Guide 97
  • Compaq DS-DSGGC-AB | Installation Guide - Page 98
    when standing on conductive floors or dissipating floor mats. ■ Use conductive field service tools. ■ Use a portable field service kit with a folding static-dissipating work mat. If you do not have , contact your HP authorized reseller. 98 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 99
    Technical Specifications This appendix covers the following topics: ■ Dimensions, page 100 ■ Power Supply Specifications, page 101 ■ Environmental Requirements, page 102 ■ Memory Specifications, page 103 C SAN Switch 2/16 Version 3.1.x Installation Guide 99
  • Compaq DS-DSGGC-AB | Installation Guide - Page 100
    1.72 +/- 0.01 inches (4.37 +/- 0.03 cm) 24.5 +/- 0.03 inches (62.2 +/- 0.1cm) 17 inches (43.2 cm) 28.0 lbs (12.7 kg) 100 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 101
    BTU/Hr/Watts = 580 BTU/hr 10 Amps Peak, > 300 usec - hot/cold start Fused in both hot & neutral lines . SAN Switch 2/16 Version 3.1.x Installation Guide 101
  • Compaq DS-DSGGC-AB | Installation Guide - Page 102
    , 11MS duration, half sine 20G, 11MS duration, sq.wave 5G, 0-3 kHz at 1.0 octave/minute 10G, 0-5kHz at 1.0 octave/minute 102 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 103
    requires a straight Serial cable with a female 9-pin subminiature-D connector. Only pins 2, 3, and 5 are supported; if pin 7 is used, the signal must always be driven high, using the pinouts listed in Data GND Logic Ground CTS Clear to Send SAN Switch 2/16 Version 3.1.x Installation Guide 103
  • Compaq DS-DSGGC-AB | Installation Guide - Page 104
    Technical Specifications 104 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 105
    glossary Glossary This glossary defines terms used in this guide or related to this product and is not a comprehensive glossary of to interface with a set of services. Arbitrated Loop A shared 100 MBps or 200 MBps Fibre Channel transport structured as a loop. Can support up to 126 devices and one
  • Compaq DS-DSGGC-AB | Installation Guide - Page 106
    that depends entirely on the use of commands, such as through telnet or SNMP, and does not involve a GUI. 106 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 107
    routing frames. Usually automatically assigned by the switch, but can be manually assigned. E_D_TOV Error Detect Time-out Value; the minimum amount recipient port to an originating port. Used by Class 1 and 2 services to manage the exchange of frames across the fabric between source and destination
  • Compaq DS-DSGGC-AB | Installation Guide - Page 108
    Channel Protocol; mapping of protocols onto the Fibre Channel standard protocols. For example, SCSI FCP maps SCSI-3 onto Fibre Channel. Fibre Channel Transport A protocol service that supports communication between Fibre Channel service providers. 108 SAN Switch 2/16 Version 3.1.x Installation
  • Compaq DS-DSGGC-AB | Installation Guide - Page 109
    Login; the process by which an N_Port determines whether a fabric is present, and if so, exchanges service parameters with it. Frame The Fibre Channel structure used to transmit data between ports. Consists of a (1,062,500,000 bits/second). SAN Switch 2/16 Version 3.1.x Installation Guide 109
  • Compaq DS-DSGGC-AB | Installation Guide - Page 110
    or non-participating mode. Latency The period of time required to transmit a frame, from the time it is sent until it arrives. Link Services A protocol for link-related actions. Link As applies to Fibre Channel, a physical connection between two ports, consisting of both transmit and receive fibers
  • Compaq DS-DSGGC-AB | Installation Guide - Page 111
    . Open Recipient The L_Port that receives the OPN ordered set from the open originator, and then enters the Open state. SAN Switch 2/16 Version 3.1.x Installation Guide 111
  • Compaq DS-DSGGC-AB | Installation Guide - Page 112
    a series of tests run by a switch after it is turned on. Private Device A device that supports arbitrated loop protocol and can interpret 8-bit addresses, but cannot log into the fabric. Private Loop An with either private or public NL_Ports. 112 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 113
    Public Device A device that can log into the fabric and support 20-bit addresses (or has 20-bit phantom addresses created frames transmitted in the same direction between two N_Ports. Service Rate The rate at which an entity can service requests. SAN Switch 2/16 Version 3.1.x Installation Guide 113
  • Compaq DS-DSGGC-AB | Installation Guide - Page 114
    in the Open state. Translative Mode A mode in which private devices can communicate with public devices across the fabric. 114 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 115
    cannot send messages, but can retransmit messages within the loop. A port in the XMITTED CLOSE state cannot attempt to arbitrate. SAN Switch 2/16 Version 3.1.x Installation Guide 115
  • Compaq DS-DSGGC-AB | Installation Guide - Page 116
    logical groupings of devices. Devices in a zone can only access and be accessed by devices in the same zone. 116 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 117
    conventions 11 prerequisites 10 related documentation 10 domain address 69 domain ID 70 configuring 65 default 65 domain IDs 65 SAN Switch 2/16 Version 3.1.x Installation Guide 117
  • Compaq DS-DSGGC-AB | Installation Guide - Page 118
    G getting help 15 H hardware features 19 help, obtaining 15 HP authorized reseller 16 storage website 15 technical support 15 hyperterminal 59 hyperterminal port settings 60 I ID domain 70 inner slide rails 32 installing 31, 32, the rack 39 POST 57, 58 SAN Switch 2/16 Version 3.1.x Installation Guide
  • Compaq DS-DSGGC-AB | Installation Guide - Page 119
    selecting an operating location 27 SAN Switch 2/16 Version 3.1.x Installation Guide Index separating inner rail from outer rails 31 serial port cabling pinouts 27 symbols in text 11 symbols on equipment 12 T technical support, HP 15 telnet 79 managing by 78 temperature, requirements 102 tests
  • Compaq DS-DSGGC-AB | Installation Guide - Page 120
    Index W warning rack stability 14 symbols on equipment 12 web tools 78 websites HP storage 15 weight, switch 100 Z zoning summary 18 120 SAN Switch 2/16 Version 3.1.x Installation Guide
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
installation
guide
hp
StorageWorks
SAN switch 2/16
version 3.1.x
Product Version:
3.1.x
Third Edition (June 2003)
Part Number:
AA-RR84C-TE
This installation guide provides basic procedures for setting up, configuring, and managing
the SAN Switch 2/16 and SAN Switch 2/16 power pak models.