Compaq ProLiant 400 ProLiant ML330 Setup and Installation Guide
Compaq ProLiant 400 Manual
View all Compaq ProLiant 400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Compaq ProLiant 400 manual content summary:
- Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 1
ProLiant ML330 Setup and Installation Guide First Edition (April 2000) Part Number 173868-001 Compaq Computer Corporation - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 2
of Microsoft Corporation. Pentium is a registered trademark of Intel Corporation. Other product names mentioned herein may be trademarks and/or registered trademarks of their respective companies. Compaq ProLiant ML330 Setup and Installation Guide First Edition (April 2000) Part Number 173868 - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 3
and System Memory 1-7 Expansion Slots 1-7 Disk Controller 1-7 Network Controller 1-7 Ports/Connectors 1-7 BIOS...1-8 Server Feature Board Components 1-8 Power Supply...1-9 Warranty ...1-9 Server Configuration and Management 1-9 BIOS Setup Utility 1-10 Compaq SmartStart and Support Software - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 4
Compaq ProLiant ML330 Setup and Installation Guide Chapter 2 Overview of Server Installation Selecting a Site...2-2 Unpacking the Server 2-2 Locating Materials 2-2 Connecting the Power Cord and Peripheral Devices 2-3 Installation Sequence 2-4 Preconfigured Operating System 2-4 Operating System - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 5
to an Internal SCSI Hard Drive or Other SCSI Device 4-5 Connecting Internal Hard Drives to Smart Array Controllers 4-6 Connecting the Server Management Information Cable (SMIC 4-8 Chapter 5 Server Configuration and Utilities BIOS Setup Utility 5-2 Navigating the BIOS Setup Utility 5-2 Using - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 6
vi Compaq ProLiant ML330 Setup and Installation Guide Regulatory Compliance Notices continued Battery Replacement Notice A-6 Laser Compliance A-7 Power Cords...A-8 Appendix B Electrostatic Discharge Grounding Methods B-2 Appendix C Switches and Jumpers Switch Settings...C-1 System Board Switch - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 7
About This Guide This guide is designed to be used as step-by-step instructions for installation and as a reference for operation, troubleshooting, and future upgrades. Text Conventions This document uses the following conventions to distinguish elements of text: Keys Keys display in boldface. - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 8
Compaq ProLiant ML330 Setup and Installation Guide Symbols in Text These symbols may be found in the text of this guide. They have the following meanings: WARNING: Text set . IMPORTANT: Text set off in this manner presents clarifying information or specific instructions. NOTE: Text set off in this - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 9
About This Guide ix Symbols on Equipment These icons may be located on equipment in not observed. Consult your documentation for specific details. This symbol indicates the presence of hazardous energy circuits or electric shock hazards. Refer all servicing to qualified personnel. WARNING: To reduce - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 10
Help If you have a problem and have exhausted the information in this guide, you can get further information and other help in the following locations. Compaq Technical Support In North America, call the Compaq Technical Phone Support Center at 1-800-OK-COMPAQ. This service is available 24 hours - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 11
About This Guide xi Compaq Website The Compaq website has information on this product as well as the latest drivers and Flash ROM images. You can access the Compaq website by logging on to the Internet: http://www.compaq.com Compaq Authorized Reseller For the name of your nearest Compaq authorized - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 12
and BIOS Setup Utility. Server features include: Intel 256-KB Pentium III processor with 133-MHz front side system bus 64 MB of PC133-MHz registered, Error Checking and Correcting (ECC), Synchronous Dynamic Random Access Memory (SDRAM) DIMMs, upgradable to 2 GB Capacity for five 18 GB hard drives - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 13
1-2 Compaq ProLiant ML330 Setup and Installation Guide ML330 Figure 1-1. Compaq ProLiant ML330 Standard Features The following features are standard on the ProLiant ML330, unless otherwise noted. - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 14
Server Features 1-3 Front Panel Components The ProLiant ML330 supports a maximum of seven internal drive bays. Figure 1-2 and Table 1-1 show the drive configuration. Figure 1-3 and Table 1-2 show the front panel components, including buttons and LED indicators. 1 2 3 4 5 6 7 Figure 1-2. Identifying - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 15
1-4 Compaq ProLiant ML330 Setup and Installation Guide 1 2 3 5 4 6 7 Figure 1-3. Front panel components Table 1-2 Front Panel Components Item Component CD-ROM drive activity LED CD-ROM drive eject button Diskette drive activity LED Diskette drive eject button Item Component Power button - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 16
Server Features 1-5 Rear Panel Connectors Figure 1-4 and Table 1-3 show the connectors on the rear panel of the ProLiant ML330. 1 2 3 4 5 6 7 Figure 1-4. Identifying rear panel connectors Table 1-3 Rear Panel Connectors Item Connector Power cord Mouse Keyboard Serial port Item Connector - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 17
1-6 Compaq ProLiant ML330 Setup and Installation Guide System Board Components Figure 1-5 and Table 1-4 show the components and connectors on the ProLiant ML330 system board. 14 13 15 16 12 11 9 8 10 7 6 5 4 3 21 17 18 19 20 21 22 24 23 Figure 1-5. Identifying system board components Table - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 18
Server Features 1-7 Processors and System Memory Pentium III processor with integrated 256-KB Cache Single Processor capability ECC for memory error detection and correction 64-MB, PC133-MHz ECC registered SDRAM DIMM system memory, expandable to 2 GB Support for 64-MB, 128-MB, 256-MB, or 512-MB, - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 19
1-8 Compaq ProLiant ML330 Setup and Installation Guide BIOS ROMPaq Utility for BIOS firmware upgrade BIOS Setup Utility for system configuration Server Feature Board Components Figure 1-6 and Table 1-5 show the components on the ProLiant ML330 Server Feature Board. 2 1 9 3 8 4 7 6 5 - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 20
included with your server Server Configuration and Management The ProLiant ML330 offers an extensive set of features and optional tools to support effective server management and configuration, including: BIOS Setup Utility Compaq SmartStart and Support Software Compaq Insight Manager Diagnostic - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 21
ROMPaq utilities to upgrade flash BIOS Compaq SmartStart and Support Software SmartStart, located on the SmartStart and Support Software CD, is the intelligent way to set up your Compaq server. SmartStart includes: Driver updates Assisted operating system installations For information concerning - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 22
on Password Diskette Drive Control Diskette Write Control Diskette Boot Override CD Boot Override Intruder Alert Most security features are established through the Compaq BIOS Setup Utility. For information concerning server security features, refer to the SmartStart and Support Software CD included - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 23
2 Chapter Overview of Server Installation The following instructions are provided as an overview for first-time installation of your ProLiant ML330. If you have any problems, contact your Compaq authorized reseller. WARNING: To reduce the risk of electric shock or damage to the equipment: Do not - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 24
with your ProLiant ML330: Keyboard Mouse Power cord Documentation label inside the server (most of the option installation and setup instructions are Phillips screwdriver Options or peripherals, such as expansion boards, monitors, uninterruptible power supply (UPS), memory, or drives Application - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 25
cord and peripheral devices to the connectors located on the rear panel of the server as indicated in Figure 2-1 and Table 2-1. See Chapter 3, "Hardware Options Installation," or see the options kits for detailed instructions. WARNING: To reduce the risk of electrical shock or fire, do not plug - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 26
2-4 Compaq ProLiant ML330 Setup and Installation Guide Installation Sequence CAUTION: If your server has a factory-installed operating system, configure it using the instructions in the following section. Otherwise, follow the instructions in the "Operating System Purchased Separately" section later - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 27
drive bay door open. c. Press the center of the power button on the front of the server. 2 1 3 Figure 2-2. Powering up the server 2. Follow the screen instructions to complete the factory-installed operating system process. 3. Refer to Chapter 5, "Server Configuration and Utilities," and the Compaq - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 28
2-6 Compaq ProLiant ML330 Setup and Installation Guide Operating System Purchased Separately If you purchased your operating system (OS) separately, you must install it using the SmartStart and Support Software CD. Refer to the Server Setup and Management pack for instructions on using SmartStart. - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 29
the Server The BIOS Setup Utility can be used to configure the server and options. To invoke the setup utility, press the F10 key when prompted during the startup process. The SmartStart and Support Software CD contains the ROMPaq and updated drivers, and assists with the operating system - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 30
Installation This chapter provides procedures for installing, removing, and replacing hardware options on the ProLiant ML330. CAUTION: Electrostatic discharge can damage electronic components. Be sure you are properly grounded before beginning any installation procedure. NOTE: As a security measure - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 31
3-2 Compaq ProLiant ML330 Setup and Installation Guide Shutting Down the Server Before installing or removing options, prepare your server by following these steps: CAUTION: Failure to follow these directions could result in damage to equipment or loss of information. 1. Back up your server data and - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 32
Hardware Options Installation 3-3 Removing the Front Bezel To remove the front bezel: CAUTION: Before removing the front bezel, make sure that the server is powered down, all cables are disconnected from the back of the server, and the power cord is disconnected from the grounded (earthed) AC outlet - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 33
3-4 Compaq ProLiant ML330 Setup and Installation Guide Removing the Access Panel To remove the access panel: WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching. CAUTION: Before removing the access panel, make sure that the - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 34
Hardware Options Installation 3-5 Removing the Bezel Blanks To remove a bezel blank from the front bezel: CAUTION: Before removing the front bezel, make sure that the server is powered down, all cables are disconnected from the server, and the power cord is disconnected from the grounded AC. 1. - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 35
3-6 Compaq ProLiant ML330 Setup and Installation Guide Removing a Drive Tray NOTE: The drive trays in the removable media bays may be used to mount internal 3.5-inch hard drives. The rails mounted inside the drive trays may be removed, and used to mount other devices in the removable media bays. To - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 36
Hardware Options Installation 3-7 Storage Devices This section discusses removal and replacement procedures for the storage devices supported on the ProLiant ML330. Drive Positions The ProLiant ML330 supports a maximum of seven internal drive bays. Figure 3-5 and Table 3-1 show the drive - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 37
3-8 Compaq ProLiant ML330 Setup and Installation Guide Installing a Hard Drive To install a 3.5-inch hard drive: CAUTION: Before removing the front bezel, make sure that the server is powered down, all cables are disconnected from the server, and the power cord is disconnected from the grounded AC. - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 38
hard drive 7. Slide the drive compartment back into the chassis. 8. Connect the power and data cables to the back of all devices. Figure 3-8. Connecting the hard drive cables 9. Replace the access panel and the front bezel. 10. Restore power to the server. NOTE: Using a non-Ultra2 drive impacts SCSI - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 39
3-10 Compaq ProLiant ML330 Setup and Installation Guide Removing a Hard Drive To remove a 3.5-inch hard drive: CAUTION: Before removing the access panel, make sure that the server is powered down, all cables are disconnected from the server, and the power cord is disconnected from the grounded AC. - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 40
the access panel and the front bezel. 8. Restore power to the server. Installing a Hard Drive in a Removable Media Bay IMPORTANT: If you are installing a hard drive into a removable media drive bay, you must use a drive tray. This drive tray can be found in the removable media bay. See "Removing - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 41
3-12 Compaq ProLiant ML330 Setup and Installation Guide 2. Set the drive into the drive tray. 3. Tighten the screws on the bottom of the drive tray to secure the drive into the drive tray. 1 2 Figure 3-11. Installing a hard drive into removable media bay drive tray 4. Slide the drive tray into the - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 42
must manually set the SCSI device ID on each device to a unique value in the range of 0 to 6 for each SCSI bus. Refer to the documentation provided with the drive for instructions on how to set the SCSI device ID. 3. Remove all terminating jumpers from third-party SCSI devices. (Compaq SCSI cables - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 43
the beginning of this chapter. 2. To configure the device, set the SCSI device ID. You must manually set the SCSI device ID on each device to a unique value in the range of 0 to 6 for each SCSI bus. Refer to the documentation provided with the drive for instructions on how to set the SCSI device ID. - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 44
the Bezel Blanks" earlier in this chapter. 6. Replace the access panel and the front bezel. 7. Restore power to the server. Removing a Tape Drive or Other Device from the Removable Media Bay To remove a tape drive or other device: CAUTION: Before removing the access panel, make sure that the - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 45
3-16 Compaq ProLiant ML330 Setup and Installation Guide 2. Disconnect the power and data cables from removable media bay 5. Install another device or a drive tray. Replace the bezel blank(s). See "Removing the Bezel Blanks" and "Removing a Drive Tray" earlier in this chapter. 6. Replace the access - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 46
Hardware Options Installation 3-17 Expansion Slots Figure 3-17 and Table 3-2 identify the location of expansion slots. 1 2 3 4 5 6 Figure 3-17. Locating expansion slots Table 3-2 Expansion Slots Item Slot Type 64-bit PCI (half-length) 64-bit PCI 32-bit PCI (Server Feature Board) 32-bit PCI - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 47
3-18 Compaq ProLiant ML330 Setup and Installation Guide Installing an Expansion Board To install an expansion board: CAUTION: Before removing the access panel, make sure that the server is powered down, all cables are disconnected from the back of the server, and the power cord is disconnected from - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 48
Hardware Options Installation 3-19 3. Insert the expansion board into the system. However, interrupt conflicts may occur between PCI devices. NOTE: Interrupt sharing does not present a problem for like devices, such as two network interface controllers. BIOS Setup Utility NOTE: Interrupt settings - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 49
3-20 Compaq ProLiant ML330 Setup and Installation Guide Memory Modules Technical Information and Important Guidelines for DIMM Installation CAUTION: Before removing the access panel, make sure that the server is powered down, all cables are disconnected from the back of the server, and the power - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 50
Hardware Options Installation 3-21 Installing a Memory Module The ProLiant ML330 supports PC133-MHz registered ECC SDRAM DIMMs. Additional DIMMs (64-MB, 128-MB, 256-MB, or 512-MB) are available to upgrade the memory. The server has four DIMM slots located on the system board. DIMMs do not need to be - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 51
3-22 Compaq ProLiant ML330 Setup and Installation Guide To install a DIMM: 1. Follow the steps in "Removing the Access Panel" at the beginning of this chapter. 2. Press outward on both latches of the DIMM - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 52
Hardware Options Installation 3-23 Removing a Memory Module To remove a DIMM: 1. Follow the steps in "Removing the Access Panel" at the beginning of this chapter. 2. Press outward on both latches of the - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 53
3-24 Compaq ProLiant ML330 Setup and Installation Guide Replacing the Battery The ProLiant ML330 has nonvolatile memory, which requires a battery to retain system information. There is a battery on the system board and a battery on the Server Feature Board. These batteries are required to maintain - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 54
holder. Lift the battery away from the holder. 1 2 Figure 3-24. Removing the battery from the system board 4. Slide the replacement battery into the proper position with the positive (+) side up. IMPORTANT: Positive polarity should be positioned up. 5. Run the BIOS Setup Utility to reconfigure your - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 55
3-26 Compaq ProLiant ML330 Setup and Installation Guide Replacing the Server Feature Board Battery WARNING: The Server Feature Board contains a lithium outlet. CAUTION: Static electricity can damage electronic components of the server. Before beginning these procedures, be sure you are discharged of - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 56
up. Figure 3-25. Replacing the Server Feature Board battery 5. Replace the Server Feature Board in expansion slot 3. See "Installing an Expansion Board" earlier in this chapter. 6. Replace the server access panel and connect cables to the server. 7. Run the BIOS Setup Utility to reconfigure your - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 57
, as well as information about all critical system cabling. Consider the following guidelines when adding SCSI devices: As a general rule, a maximum of seven devices may be added per channel. Your server is equipped with one Wide-Ultra2 SCSI channel. Be sure to remove all terminating jumpers from - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 58
4-2 Compaq ProLiant ML330 Setup and Installation Guide Identifying the Internal SCSI Components The SCSI cable shown in Figure 4-1 is included with your server. 1 Figure 4-1. Identifying the SCSI cable with terminator The SCSI cable shown in this illustration supports up to five SCSI devices and - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 59
cabling the server, note the removable media and hard drive compartment locations as shown in Figure 4-2 and Table 4-1. For additional information about installing optional SCSI devices, refer to the documentation included with the SCSI devices. 1 2 3 Figure 4-2. Internal SCSI components Number - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 60
Compaq ProLiant ML330 Setup and Installation Guide Identifying and Connecting a Fast SCSI-2 Device (Narrow) Some SCSI devices require a special adapter, which is not standard with your server, to connect with the SCSI cable included with your server. Figure 4-3. 68-to-50 pin (wide-to-narrow) SCSI - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 61
Device in a Removable Media Bay" in Chapter 3. 2. Make sure the SCSI ID is uniquely set for each device. 3. Locate the Wide-Ultra2 SCSI cable attached to the SCSI connector. 4. Install the next available connector to the hard drive or SCSI device. 5. Install the next available power connector to the - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 62
4-6 Compaq ProLiant ML330 Setup and Installation Guide Connecting Internal Hard Drives to Smart Array Controllers Many configurations are possible when adding multiple SCSI controllers. This section outlines the cabling procedure for the Smart Array Controller. Refer to the Smart Array Controller - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 63
Guidelines 4-7 4. Reconnect the Wide-Ultra2 SCSI cable to the Smart Array Controller. Figure 4-6. Connecting the Wide-Ultra2 SCSI cable to the Smart Array Controller NOTE: The SCSI connector on the Server Feature Board is self-terminating. If you choose not to use the SCSI connector, you do not need - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 64
Compaq ProLiant ML330 Setup and Installation Guide Connecting the Server Management Information Cable (SMIC) The Server Management Information Cable (SMIC) provides system critical management information to the operating system. Proper SMIC connections help avoid potential system failure and BIOS - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 65
about the utilities and tools provided with the ProLiant ML330. The following tools and utilities are described in this chapter: BIOS Setup Utility ROMPaq SmartStart Compaq Insight Manager SmartStart Diskette Builder Compaq Survey Utility Compaq Diagnostics Utility Automatic Server Recovery (ASR) - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 66
Utility are not required in the setup of your server. The options in this utility are designed to assist with specific server configuration issues. The BIOS Setup Utility is separated into a series of menu selections designed to configure specific areas of the system. The primary menus are the File - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 67
MB diskette in the diskette drive and stores the configuration in the system. This can be used to restore the system to an archived configuration. Set Defaults and Exit restores default configuration values for the system. This option can be used if the system has been incorrectly configured. Ignore - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 68
5-4 Compaq ProLiant ML330 Setup and Installation Guide The System Menu The System menu is used for overall system configuration settings. The following is a list of selections found in this menu with an explanation of each option: System Information displays the current system configuration. This - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 69
and to select which device the system scans first. Hard Drive Controller Order allows manual selection of the controller. When the system displays the "attempting to Boot from C:" message, the system searches the selected controller for an operating system. Whenever an additional storage adapter is - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 70
IDE controller. IMPORTANT: Compaq recommends that you do not disable the embedded SCSI controller. Doing so disables certain system management features. PCI IRQ Configuration allows a manual interrupt request (IRQ) for a specific PCI device. The system automatically assigns IRQ settings for all PCI - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 71
and disables the wake support (PME), such as Wake On LAN ROMPaq Using Flash ROM in Compaq servers allows the firmware (BIOS) to be upgraded with system or option ROMPaq utilities. To upgrade the BIOS, insert a ROMPaq diskette into the diskette drive, then remove power from the system, and then power - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 72
a factory-installed operating system. Refer to the Compaq Factory-Installed Operating System Software User Guide. To install the SmartStart and Support Software CD, run F10 setup (BIOS Setup Utility) and configure the primary operating system. Next, follow these steps: 1. With your server powered up - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 73
Builder utility; however, if the system does not support the "auto-run" feature, use Windows Explorer to run [CD-ROM DRIVE]:\DSKBLDR\DSKBLDR.EXE. Compaq Survey Utility The Compaq Survey Utility is an online information gathering agent that runs on servers, collecting critical hardware and software - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 74
Survey Utility diskettes. To install the Compaq Survey Utility from the Compaq Management CD on a NetWare server, enter the following at the NetWare system prompt: Load [CD-ROM DRIVE]:\Survey\Netware\Eng\Sinstall Running Survey Once the Compaq Survey Utility is installed, it gathers information - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 75
is a feature in ProLiant servers that causes the system to restart in the event of a catastrophic OS error like a blue-screen, ABEND (abnormal end), or panic. A system failsafe timer, the ASR timer, is started when the Compaq System Management driver, also known as the health driver, is loaded. The - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 76
compliance certifications and identification, your server is assigned a Compaq series number. The Compaq series number for the ProLiant ML330 is Series ES1014. The series number can be found on the interference potential of the device as well as additional operating instructions for the user. - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 77
A-2 Compaq ProLiant ML330 Setup and Installation Guide The rating label on the device shows which class (A or B) radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 78
: Compaq Computer Corporation P. O. Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 Or, call 1-800-652-6672 (1-800-OK-COMPAQ). Compaq Computer Corporation P. O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 Or, call 281-514-3333 To identify this product, refer to the Part, Series - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 79
A-4 Compaq ProLiant ML330 Setup and Installation Guide Mouse Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 80
Japanese Notice Regulatory Compliance Notices A-5 Taiwanese Notice - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 81
A-6 Compaq ProLiant ML330 Setup and Installation Guide Battery Replacement Notice Your computer is provided with a recycling or proper disposal, use the public collection system or return them to Compaq, your Compaq authorized service resellers or authorized service providers, or their agents. - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 82
The CD-ROM drive contains a laser diode of gallium aluminum arsenide (GaAlAs) emitting in the wavelength range of 780 +/- 35 nm. All Compaq systems equipped with a laser device comply with safety standards, including International Electrotechnical Commission (IEC) 825. With specific regard to the - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 83
A-8 Compaq ProLiant ML330 Setup and Installation Guide Power Cords If you were not provided with m (12 feet). If you have questions about the type of power cord to use, contact your Compaq authorized service provider. A power cord should be routed so that it is not likely to be walked on or pinched - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 84
, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 85
B-2 Compaq ProLiant ML330 Setup and Installation Guide Grounding Methods There are several methods for grounding. when standing on conductive floors or dissipating floor mats. Use conductive field service tools. Use a portable field service kit with a folding static-dissipating work mat. If you do - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 86
with running the BIOS Setup Utility. Switch Settings The ProLiant ML330 system board has two switches that are used to set configuration and processor speed options on your server. The Server Feature Board has a switch, that is used to set configuration options on the Server Feature Board. Refer - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 87
C-2 Compaq ProLiant ML330 Setup and Installation Guide System Board Switch Settings The following tables define the function for each switch setting: Table C-1 Processor Speed Switch Settings (SW1) Switch 1 2 3 4 Function Reserved Reserved Reserved Reserved Table C-2 System Configuration Switch - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 88
SCSI controller can have the same SCSI ID. If another SCSI device is connected to the same controller, check its SCSI ID before beginning the installation procedure for the additional device. The SCSI ID is set by jumpers located on each SCSI device. Refer to your SCSI device option documentation - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 89
ASR advanced menu 5-7 disabling 5-11 authorized resellers, locating xi Automatic Server Recover See ASR B batteries dangers of A-6 disposal methods A-6 information bezel blanks removing 3-5 removing, illustrated 3-5 replacing 3-5 BIOS Setup Utility changing interrupts 3-19 configuration 1-10, 2-7, - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 90
1-8 system board 1-6 boot order, storage menu 5-5 C cabling devices, illustrated 3-16 FCC Rules and Regulations A-3 guidelines 4-1 hard drives, illustrated 3-9, 3-10, 3-12 instructions 4-5 server 4-1 Server Management Information Cable 4-8 Smart Array Controller 4-6 Wide-Ultra2 SCSI integrated - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 91
configuration archive 5-3 data back up 5-3 default values 5-3 information, recording 3-2 PCI devices 3-19 restore system settings 5-3 server 5-1 server with BIOS Setup Utility 2-7 tools 1-9 connecting Fast SCSI-2 device 4-4 hard drive to Smart Array Controller 4-6 peripheral devices 2-3 power cord - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 92
4 Compaq ProLiant ML330 Setup and Installation Guide controllers disk 1-7 IDE 5-5 network interface (NIC) 1-7 Wide-Ultra2 SCSI, integrated 4-5 D data back up 3-2, 5-3 date and time, system menu 5-4 dealers, locating xi device installation in 5.25-inch drive bay, illustrated 3-13 diagnostic tools ASR - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 93
getting help x grounding methods B-1, B-2 guidelines cabling 4-1 PCI devices 5-6 SCSI devices 4-1 Index 5 H hard drive controller order, storage menu 5-5 hard drives installing 3-8, 3-11 installing, illustrated 3-9 number supported 1-3 removing 3-10 removing, illustrated 3-11 Smart Array Controller - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 94
x, xi technical support telephone numbers x I icons, used on equipment ix illustrations battery location 3-25 cabling Wide-Ultra2 SCSI integrated controller 4-5 Compaq ProLiant ML330 1-2 connecting hard drive cables 3-9, 3-12 hard drives to Smart Array Controller 4-7 Server Management Information - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 95
hard drive 3-8 hard drive in removable media bay drive tray, illustrated 3-12 hard drive using drive tray 3-11 hardware options 3-1 operating system 2-6 other device 3-13 preconfigured operating system 2-4 server 2-1 SmartStart 5-8 tape drive 3-13, 3-14 interrupt See also IRQ changing 3-19 settings - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 96
3-24 front bezel 3-3 hard drives 3-10 hardware options 3-1 media device 3-15 memory modules 3-23 tape drive 3-15 replacing access panel 3-4 battery 3-24 bezel blanks 3-5 drive tray 3-6 front bezel 3-3 resellers, locating xi reset, interrupt settings 3-19 restoring system settings from floppy 5-3 RJ - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 97
SCSI connector 4-7 SCSI devices adapter specifications 4-4 additional information 4-3 connecting Wide-Ultra2 SCSI integrated controller 4-5 Fast SCSI-2, connecting 4-4 guidelines 4-1 jumper settings C-3 security features 1-11 server cabling guidelines 4-1 Compaq series number A-1 configuration 2-7, - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 98
Board Components 1-8 Server Feature Board Configuration Switch Settings (SW1) C-3 System Board Components 1-6 System Configuration Switch Settings (SW2) C-2 Taiwanese Notice A-5 tape drive installation 3-14 installation, illustrated 3-15 removing 3-15 technical support Compaq website x telephone - Compaq ProLiant 400 | ProLiant ML330 Setup and Installation Guide - Page 99
removing all power from system 2-1 RJ-45 receptacle ix warranty, server 1-9 wattage, power supply 1-9 website address, Compaq x, xi Wide-Ultra2 SCSI cable connecting 4-7 removing, illustrated 4-6 Wide-Ultra2 SCSI integrated controller 4-5 Wide-Ultra2 SCSI integrated controller cabling, illustrated
ProLiant ML330
Setup and Installation Guide
First Edition (April 2000)
Part Number 173868-001
Compaq Computer Corporation