Compaq ProSignia 300 Compaq ProSignia 300 Servers Maintenance and Service Guid
Compaq ProSignia 300 Manual
View all Compaq ProSignia 300 manuals
Add to My Manuals
Save this manual to your list of manuals |
Compaq ProSignia 300 manual content summary:
- Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 1
in accordance with the terms of the agreement. Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies. MAINTENANCE AND SERVICE GUIDE COMPAQ PROSIGNIA 300 SERVERS First Edition (December 1994) Text Number 137786-001 - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 2
Preface This Maintenance and Service Guide is a troubleshooting guide that can be used for reference when servicing the Compaq ProSignia 300 Server. Compaq Computer Corporation reserves the right to make changes without notice. Symbols The following text and symbols mark special messages throughout - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 3
, plug the AC power cord into a properly grounded AC outlet only Locating Additional Information The following documentation is available to support these products: o User Documentation o Compaq Service Quick Reference Guide o Service Training Guides o Compaq Service Advisories and Bulletins - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 4
Chapter 1. Illustrated Parts Catalog Chapter 1.0 Introduction This chapter provides the illustrated parts breakdown and a spares parts list for the Compaq ProSignia 300 Server. Chapter 1.1 Exploded View and Spares Parts List - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 5
Table 1-1. Spares Parts List - Compaq ProSignia 300 Ref Description Part Number CHASSIS: -------- 1 Chassis 194491-001 2 J Hood 197836-001 3 Side CD and Diskette Drive rails) 197841-001 8 System Fan with Bracket and Guard 211442-001 9 Board Guide and Speaker Holder 197835-001 - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 6
16 Power Supply 200W 197416-001 BOARDS: ------17 System Board I/O 184359-001 18 Processor Board for 5/75 MHz Processor (not included) 211454-001 19 Processor Board for 5/90 MHz Processor (not included) 211450-001 20 5/75 MHz Processor Chip with Heatsink 211455-001 21 5/90 MHz Processor - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 7
27 2.1 GB Fast-Wide SCSI-2 Drive 28 4.3 GB Fast-Wide SCSI-2 Drive 29 Tray Load CD-ROM Drive (Internal) 30 Tray Load CD-ROM Drive (External) 31 1.44 MB, 3.5" Diskette Drive 32 1.2 MB, 5.25" Diskette Drive 33 2/8 GB DAT Drive with Compression 34 525 MB ACA Tape Drive 35 1.2 GB ACA Tape Drive 36 4/16 - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 8
160648-117 * 45 Keyboard, Belgian 160648-118 * 46 Mouse 141189-201 * Ref Description Part Number MISCELLANEOUS: 47 Battery 160274-001 48 Maintenance and Service Guide 211462-001 * 49 System ROMpaq 143198-001 * 50 Option ROMpaq 142207-001 * 51 Shipping Boxes 211444-001 - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 9
support software guide for procedures on using the Compaq System Configuration utility when installing or removing expansion boards, mass storage devices, and Extended Industry Standard Architecture (EISA) or Peripheral Component Interconnect (PCI) options. To service the Compaq ProSignia 300 Server - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 10
the AC power cord from the AC outlet, then from the system unit. 3. Disconnect all external peripheral devices from the server. Chapter 2.3 Side Access Panel/Front Bezel WARNING High voltage present. Extreme care must be taken when running the Compaq ProSignia 300 Server without the system - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 11
To remove the Side Access Panel 1. Loosen thumb screws (3) on back bezel. 2. Slide side access panel back and then out. To remove the Front Bezel 1. Remove front bezel retaining screw (1). 2. Push friction tabs up (located underneath bottom edge of bezel) and pull forward. 3. Pull bezel forward at - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 12
the ProSignia 300 Server without the air baffle installed. NOTE: It is not necessary to remove the air baffle to remove any of the server's components except the system I/O board. 1. Press the retaining latch (A) and swing the air baffle out away from the chassis. 2. Place a flat bladed screw driver - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 13
The ProSignia 300 Server has two 3 1/2 drive bays and three 5 1/4 drive bays. - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 14
front bezel. 2. Disconnect power and signal cables from rear of drive. 3. Remove retaining screws (2). 4. Slide mass storage device out. 5. Reverse steps to install replacement. IMPORTANT: When replacing hard drives remove rails before returning the hard drive to Compaq. Replacement rails are not - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 15
- Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 16
Chapter 2.7 Boards This section describes how to remove and replace the processor board, memory modules, option boards, and the system board. Processor Board - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 17
1. Remove retaining screw and pull board straight out. 2. Reverse steps for processor board installation. Memory - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 18
if installed memory size has changed. The Compaq ProSignia 300 Server comes standard with 16 MB of ECC system memory. Memory can be expanded to a maximum of 208 MB by installing combinations of 4, 8, 16, or 32 MB 60 or 70 ns industry-standard SIMM modules in the six SIMM sockets on the processor - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 19
. Non-JEDEC SIMMs may adversely affect data integrity. Table 2-1 shows a sample of typical memory configurations for the Compaq ProSignia 300 Server. Table 2-1. Example of SIMM Upgrade Combinations Processor Board Total Memory * Bank 1 Bank 2 Bank 3 24 MB 2x4 MB 32 MB 2x8 MB 48 - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 20
1. Remove any cables connected to board. 2. Remove retaining screw and pull board straight out. System Board - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 21
1. Remove all expansion boards. 2. Label and disconnect all cables from system board. 3. Remove retaining screws (5). 4. Gently press the I/O panel release tabs and slide the system board forward far enough to clear the retaining stops. WARNING Care should be taken when handling the thin metal - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 22
External Battery 1. Make sure that the power to the system is off. 2. Secure battery to chassis (it is secured by Velcro tape) and reconnect the battery cable to fire. Use only replacement battery/clock modules supplied by Compaq Computer Corporation. Disposal of the battery/clock module should be - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 23
return methods Power Supply - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 24
's from bracket. 6. Remove screws at rear and top of power supply (4). 7. Lift power supply out pulling switch and cable through chassis. 8. Reverse order for replacement. NOTE: When replacing power supply, make sure that the power switch cable is properly threaded through the bracket strain relief - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 25
shown) out of the way. WARNING The microprocessor can be HOT. Allow sufficient time for the microprocessor and the processor board to cool before handling 3. Remove the processor board. 4. Remove clamp by pressing down and lifting up (1). 5. Unlock the connector by lifting on the release lever - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 26
Zero Insertion Force (ZIF) Socket. 2. Press the microprocessor into the microprocessor socket. 3. Lock the release lever. IMPORTANT: Avoid excessive force when installing the new microprocessor into the ZIF socket. If the microprocessor does not easily press into place, check the alignment of the - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 27
tools available for the Compaq Server products. These include: o Power-On Self-Test (POST) o Diagnostics (DIAGS) o Drive Array Advanced Diagnostics (DAAD) o Automatic Server Recovery o ROMPaq utilities to upgrade flash ROMs Chapter 3.1 Utility Access The SmartStart Installation Program CD contains - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 28
) POST is a series of diagnostic tests that run automatically on Compaq computers when the system is turned on. POST checks the following assemblies to ensure that the computer system is functioning properly: o Keyboard o Power supply o System board o Memory o Memory expansion boards o Controllers - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 29
follow the instructions in Table 3-1. The error messages and codes listed in Table 3-1 include all codes generated by Compaq products. Problem Action A Critical Error None A catastrophic system Run Diagnostics. occurred prior to error, which caused Replace failed this power-up the server - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 30
. Error Probable Source Code Beeps of Problem Action 175 - None EISA or PCI Processor None Processor type or step Run the System Configuration does not match Configuration Invalid configuration memory. Utility and correct. 179 - System None A board was installed - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 31
during installation or settings. Incorrectly upgrade. 212 - System 1 Short Processor in slot x Run Diagnostics Processor failed. and replace Failed/Mapped out failed processor. 213 - Cache size None Invalid optional cache Replace cache with Error size. 256K cache. (ProSignia - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 32
Fixture Installed keyboard. Error Probable Source Code Beeps of Problem mouse controller Authorized Error failure. Compaq Reseller. 304 - Keyboard or Video display Replace the Adapter Failure 2 Short controller. video board. Error Probable Source Code Beeps of Problem - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 33
fans. failure detected installed or spinning. 1612 - Primary 2 Short Primary power supply Replace power power supply has failed supply as soon as failure. possible. 1730 - Fixed Disk None Fixed disk drive error. Run the System 0 does not Configuration support DMA Mode Utility - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 34
Source Code Beeps of Problem Action 1751 - Fixed Disk None Fixed disk drive error. Run the System 1 failed Identify Configuration command Utility and correct. 1760 - Fixed Disk None Fixed disk drive error. Run the System 0 does not Configuration support Block Utility and - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 35
ProSignia VS alert or open side failure or side Drive Subsystem panel. panel open. Error Error Probable Source Code Beeps of Problem your service provider. Error Probable Source Code Beeps of Problem Action 1782 - Disk Controller Failure None Hard disk drive - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 36
Probable Source Code Beeps of Problem Action 1786 - Drive None Drives are not Reinstall the Incorrect Drive installed in their drives correctly Replaced: Drive X disabled. See note restart the replaced: Drive Y below. computer with Select "F1" to the drive array continue - - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 37
routing. Error Probable Source Code Beeps of Problem Action 1789 - Drive not None Cable if configured for fault tolerance. 1790 - Disk 0 None Hard drive error or Run orderly system will Accelerator memory. shut-downs to automatically be Power was then restored avoid - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 38
, power was eight to ten days. Battery Depleted interrupted while Perform orderly - Data Lost data was in the Array system shut-downs (Error message Accelerator memory. Run the System disabled. Configuration Utility to re-configure the Compaq IDA-2 without the Array Accelerator. - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 39
in continue with Disabled due to posted-writes memory. logical drives Array Accelerator disabled or F2 Data Long Power is cycled. Check fans. beeps 2 Short Temperature too hot. Processor fan not installed or a problem while running the Diagnostics program. These error codes help identify - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 40
problem isolation procedures: 1. Ensure that there is proper ventilation. The computer should Enter key. 5. If you do not have access to the password, you must disable the power-on password by using the Password Disable switch on the system board. 6. Install an loopback plug when instructed - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 41
battery and re-test. 199 - xx Installed devices test failed The following steps processor board and re-test. 6. Replace the system board and re-test Table 3-3. Memory Test Error Codes Error Description Recommended Action Code 200 - xx Invalid memory configuration Reinsert memory - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 42
processor board and re-test. 210 - xx Random pattern test failed 3. Replace the memory If disconnected, self-test failed turn off the computer and connect the keyboard. 304 - xx Keyboard 2. Check the power to the printer. 498 - xx Printer failed or not 3. Install the loopback connected - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 43
Video 40 x 25 mode test failed 508 - xx Video 320 x 200 mode color set 0 test failed 509 - xx Video 320 x 200 mode color set 1 test failed 510 - xx Video 640 x 200 mode test failed 511 - xx Video screen memory page test failed 512 - xx Video write/read/compute diskette power and signal test - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 44
to 699 - xx error codes: 1. Replace the media. 2. Run the Configuration utility Table 3-8. Monochrome Video Board Test Error Codes Error Description Recommended Action Code 802 - xx Video memory test failed The following steps apply to error codes 802 - xx and 824 - xx Monochrome - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 45
documentation for correct test failed setup procedures. 2. Check the disk read test failed 2. Replace the fixed disk drive signal and power cables and 1703 - xx Fixed disk write/read/ re-test. compare test failed 3. Replace the fixed disk drive controller and re-test. 1704 - xx Fixed disk - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 46
reset controller test failed 1710 - xx Fixed disk park head test failed 1715 - xx Fixed disk head select test failed 1716 - xx Fixed disk conditional format test failed 1717 - xx Fixed disk ECC * test failed 1719 - xx Fixed disk drive power mode test failed 1736 - xx Drive Monitoring failed 1799 - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 47
and re-test. 2408 - xx Video 320 x 320 mode color set 0 test failed 2409 - xx Video 320 x 320 mode color set 1 test failed 2410 - xx Video 640 x 200 mode test failed 2411 - xx Video screen memory page test failed 2412 - xx Video gray scale test failed 2414 - xx Video white screen test failed - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 48
Video noise pattern test failed 2417 - xx Lightpen text mode test failed, no response 2418 - xx ECG/VGC memory test failed 2419 - xx ECG/VGC ROM checksum test failed 2420 - xx ECG/VGC attribute test failed 2421 - xx ECG/VGC 640 x 200 VGA Data Path Test 1. Run Setup. 2. Replace the system board - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 49
RAM) 7000 - 15 Processor (8570 RTC) 7000 - 21 Memory 7000 - 22 Memory Write/Read 7000 - 23 Memory Address 7000 - 24 Memory Refresh Alert 7000 - 25 Memory Increment 7000 - 26 Memory Random Data 7000 - 27 Memory Disturb Address 7000 - 28 Memory HBM Replace the Server Manager/R board and - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 50
codes. 7000 - 78 Host ADC Measurements Replace the Server Manager/R board battery for 7000 - 78 and 7000 - 79 Battery 7000 - 79 error codes. Table 3-17. Pointing (DAAD) is a DOS-based tool designed to run on all Compaq products that contain a Smart SCSI Array Controller using - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 51
Diagnostics User Guide for complete details and procedures about this diagnostic tool. DAAD works by issuing multiple commands to the array controllers to determine if a problem exists. This data can then be saved to a file and, for severe situations, this file can be sent to Compaq for analysis - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 52
installed onto the IDA-2 board. You may need to run the Compaq System Configuration Utility and disable the array accelerator board to get this message off the screen Accelerator error log This is a list of the last 32 parity errors on transfers between the IDA-2 board transfer buffer and memory - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 53
data loss was detected during power-up due to all of the batteries being below the sufficient voltage memory at re-initialization. The data will be flushed to disk. This is not an error or data loss condition. No action needs to be taken Accelerator status: Warranty alert A catastrophic problem - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 54
When DAAD was verifying this interface, a serious problem was detected. A hardware problem has occurred and you should replace the IDA latest recommended version. Call your Authorized Compaq Reseller to obtain the latest upgraded firmware Controller firmware needs upgrading (DAAD Error 102) You have - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 55
controller returned an error from its internal Power-On Self Tests. Replace the controller installed in the computer has firmware version 2.30 or 2.31. Replace the drive Drive Monitoring features are unattainable DAAD was unable to get the monitor and performance data due to a fatal command problem - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 56
upgrade the firmware to a version that supports monitor and performance, if desired Drive Monitoring is NOT enabled for drive bay X The monitor and performance features have not been enabled. Run the Compaq instructions memory error Data could not be written to the array accelerator board in - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 57
X is non-Compaq supplied The installed drive was not supplied by Compaq. If problems exist with this drive, replace it with a Compaq drive Identify controller It could also occur if the firmware on the controller has been upgraded and the System Configuration Utility was not run. Check the identify - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 58
recovery mode and is vulnerable. Replace the failed drive as soon as possible Logical Drive X status = LOOSE CABLE DETECTED A physical drive has a cabling problem. Turn the system off and attempt to reattach the cable onto the drive. If this does not work, replace the cable Logical Drive X status - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 59
data miscompare Data was found at re-initialization in the posted write memory, however, the mirror data compare test failed resulting in data being bad, loose, or disconnected. Turn on the system and attempt to reconnect data/power cable to the drive. If this does not work, replace the cable. If - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 60
, the firmware running is not present on all drives. This could be caused by the addition of new drives in the system. Run the Compaq Upgrade Utility to place the latest firmware on all drives Threshold for drive (bay) X violated This message indicates that a monitor and performance threshold for - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 61
of the problem Wrong Accelerator Services The Compaq ProSignia 300 provides rapid recovery services for diagnosing and recovering from errors. These tools are available for local and remote diagnosis and recovery. The following topics are discussed here: o Automatic Server Recovery (ASR) o Server - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 62
want the Server to recover from critical system faults, and specify when to monitor. This selection process is accomplished through the SmartStart installation process and can be modified through the Compaq System Configuration Utility. The ASR depends on an operating system driver that routinely - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 63
Recovery For local or remote installations where it is desirable to supervise the recovery, ASR will log the error information to the Critical Error Log, reset the Server, test all memory, automatically de-allocate any bad memory blocks found, page you, boot the Compaq Utilities from the hard drive - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 64
The standard Compaq ProSignia 300 security password features function differently during Automatic Server Recovery-2 than during a typical system startup. During ASR the system will not prompt for the Power-On Password. This allows the ASR to restart the Operating System or Compaq Utilities without - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 65
History Table Some errors can be resolved by reviewing changes to the Compaq ProSignia 300 configuration. The Server has an Automatic Revision Tracking (ART) feature that helps you review recent changes to the Server's configuration. One ART feature is the Revision History Table, which contains the - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 66
configuration. This feature allows correlation of hardware changes with Server failure. The following information is stored in the Revision History Compaq ProSignia 300 and in certain options controllers allows the firmware (BIOS) to be upgraded with system or option ROMPaq utilities. To upgrade - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 67
CAUTION Do not turn the power off during a firmware upgrade. A loss of power during upgrade may corrupt the upgrade. - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 68
for the Compaq ProSignia 300 Server. Chapter 4.1 System Board Compaq ProSignia 300 switch locations on the system board are shown in the figure below. Switch SW1 is a six-position switch bank (S1-S6), which sets the security features and configuration of certain computer functions. System - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 69
and the integrated ON DISABLED video is disabled if ROM detects an optional video board installed. S2 CONFIGURATION LOCK OFF * bay. Figure 4-2 shows the physical locations of jumpers ID2, ID1, and ID0 on supported SCSI options. Table 4-2. Jumper Settings For SCSI ID Pin 3 Pin 2 Pin - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 70
- Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 71
and performance specifications for the following: o System Unit o Power Supply o SIMMs o Diskette Drives o Fast SCSI-2 Hard Drives o Fast-Wide SCSI-2 Hard Drives o SMART SCSI Array Controller o Integrated 32-Bit Fast-SCSI-2/P Controller o Fast-Wide SCSI-2 Controller o Compaq NetFlex-Controllers - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 72
Humidity (non condensing): Operating 20% to 80% 20% to 80% Non operating 5% to 90% 5% to 90% Chapter 5.2 Power Supply Specifications Table 5-2. Power Supply Specifications English Metric Input Specifications: Nominal Line Voltage 100 to 120 VAC 220 to 240 VAC Range Input - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 73
Specifications Table 5-3. SIMM Specifications Size 4, 8, 16, 32 MB Speed 60, 70 ns Width 32 Bits Upgrade Requirement Any matched pair of SIMMs Maximum Capacity 208 MB * The Compaq ProSignia 300 supports a maximum of 208 MB of system RAM. JEDEC standard SIMMs must be installed - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 74
to 10 MB Buffer Size 256 KB RPM 5400 rpm Average Access 9.5 ms Chapter 5.6 1.05 GB Fast-SCSI-2 Drive Specifications Table 5-6. 1.05 GB Fast-SCSI-2 Drive Specifications Capacity 1050.1 MB Block Size 512 Bytes Interface Single-Ended Fast-SCSI-2 Synchronous Transfer Up to 10 MB - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 75
ms 9.0 ms Chapter 5.8 4.3 GB Drive Specifications Table 5-8. 4.3 GB Drive Specifications Fast-SCSI-2 Fast-Wide SCSI-2 Capacity 4293.6 Controller Table 5-9. Integrated 32-Bit Fast-SCSI-2/P Controller Devices Supported Seven * Data Transfer Method 32-bit bus master SCSI Bus - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 76
SCSI Termination Active termination SCSI Connectors 1 external 2 internal (Fast-SCSI-2 and Fast-Wide SCSI-2) Table 5-11. Compaq 32-Bit Fast-Wide SCSI-2 Controller/P Drives Supported Up to seven total (internal and external) Data Transfer Method 32-bit bus master SCSI Channel - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 77
LED Indicators Cache Memory for Accelerator 4 MB Mirrored Batteries Yes Battery without Power Yes Charge Trickle Chapter 5.12 NetFlex Controllers Table 5-13. NetFlex-L ENET Specifications Network Topology Ethernet IEEE 802.3 Compliant Supported Connectors RJ-45 - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 78
EISA bus master Max. Transfer Rate on EISA bus 33 MB/s Table 5-16. NetFlex-2 TR Specifications Network Topology Ethernet IEEE 802.5 Compliant Supported Connectors RJ-45 DB-9 Processor TI TMS380C26 Coprocessor TI Packet Blaster (TMS380FPA) Data Transfer Method 32-bit Local Bus - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 79
) Data Transfer Method 32-bit EISA bus master Max. Transfer Rate on EISA bus 33 MB/s Chapter 5.13 NetFlex Connector Specifications Table 5-18. DB-9 Pinout Assignments Pin Token Ring Signal Wire Color 1 Receive Data (-) (Red) 2 GND 3 Fused +5 volts 4 GND 5 Transmit Data - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 80
8 Not Used 9 CI(-) 10 DO(-) 11 GND 12 DI(-) 13 Fused +12 volts 14 GND 15 Not Used Table 5-21. DB-26 Breakout Connector Pinout Assignments Pin Ethernet Signal Port 1 Port 2 1 CI(-1) 2 GND(1) 3 DO(+1) 4 Not Used 5 CI(-2) 6 Not Used 7 DO(+2) 8 Shield (2) 9 Fused - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 81
Table 5-23. NetFlex ENET-TR and NetFlex-2 ENET-TR Cable Specifications Ethernet cable specifications - Twisted Pair - (10Base-T) Connector type RJ-45, 8-pin Cable type Unshielded twisted pair (UTP) 22-26AWG, 100 Ohm @ 1 MHz Distance Up to 100 meters from node to concentrator Ethernet - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 82
10Base-T) Connector type RJ-45, 8-pin Cable type Unshielded twisted pair (UTP) 22-26AWG, 100 Ohm @ 1 MHz Distance Up to 100 meters from node to concentrator Ethernet cable specifications - AUI Connector type DB-15 Cable type AUI cable to external transceiver Distance Up to 50 meters - Compaq ProSignia 300 | Compaq ProSignia 300 Servers Maintenance and Service Guid - Page 83
Connector type BNC Cable type RG 58 A/U or RG 58 C/U Distance 185 meters Max length
Notice
The information in this guide is subject to change without notice.
Compaq Computer Corporation shall not be liable for technical or editorial
errors or omissions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance, or use of this
material.
This guide contains information protected by copyright. No part of this
guide may be photocopied or reproduced in any form without prior written
consent from Compaq Computer Corporation.
Copyright 1994 Compaq Computer Corporation.
All rights reserved. Printed in the U.S.A.
Compaq, Systempro, Deskpro, Compaq Insight Manager,
Registered U.S. Patent and Trademark Office.
ProSignia, Systempro/XL, ProLiant, NetFlex, ROMPaq, and QVision are
trademarks of Compaq Computer Corporation.
The software described in this guide is furnished under a license agreement
or nondisclosure agreement. The software may be used or copied only in
accordance with the terms of the agreement.
Product names mentioned herein may be trademarks and/or registered
trademarks of their respective companies.
MAINTENANCE AND SERVICE GUIDE
COMPAQ PROSIGNIA 300 SERVERS
First Edition (December 1994)
Text Number 137786-001