Compaq R6000 HP Uninterruptible Power System R6000 Models Installation Instruc
Compaq R6000 - UPS - Lead Acid Expandable Manual
UPC - 743172638854
View all Compaq R6000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Compaq R6000 manual content summary:
- Compaq R6000 | HP Uninterruptible Power System R6000 Models Installation Instruc - Page 1
. hp uninterruptible power system R6000 models installation instructions Second Edition (December 2002) Part Number 347222-003 About This Device These instructions show how to install an uninterruptible power system (UPS). For detailed information about the UPS, refer to the UPS user guide on - Compaq R6000 | HP Uninterruptible Power System R6000 Models Installation Instruc - Page 2
rack where it will be assembled, following the instructions on the carton. Verify that all components are present. Mounting the Rails The UPS must be mounted on the fixed rails supplied with the unit. Before beginning this installation process, review and adhere to the following precautions. WARNING - Compaq R6000 | HP Uninterruptible Power System R6000 Models Installation Instruc - Page 3
the cage nuts in the rear rack-mounting rails. Installing the UPS in the Rack Before attempting to install the UPS, review and adhere to all warnings provided in the "Important Safety Information" section of this document. To install the UPS in the rack: 1. With one person on each side of the - Compaq R6000 | HP Uninterruptible Power System R6000 Models Installation Instruc - Page 4
the screws and the cage nuts supplied with the rack. NOTE: After installing the UPS chassis, insert additional screws for support if any screw holes are unoccupied. 6. Verify that the UPS is disconnected from utility power. Wiring the UPS WARNING: To prevent personal injury, use a Lockout/Tagout - Compaq R6000 | HP Uninterruptible Power System R6000 Models Installation Instruc - Page 5
NOTE: For ease of service and maintenance, use screws are tightened to torque specifications found on the diagram immediately Replace the input terminal block cover. Completing the UPS Assembly Installing and Connecting the Battery Modules WARNING: To prevent personal injury, be sure that the battery - Compaq R6000 | HP Uninterruptible Power System R6000 Models Installation Instruc - Page 6
discard. c. Replace the connector cover screw to secure sheet metal. NOTE: When attaching battery cable connectors, installation are complete. 1. Attach the connector for the front panel to the electronics module receptacles (1). 2. Lift the front top bezel into place (2). 4. Secure the batteries - Compaq R6000 | HP Uninterruptible Power System R6000 Models Installation Instruc - Page 7
personal injury or damage to the equipment, the ERMs must be installed by a trained service technician. The ERM can be connected directly to an R6000 model or to another ERM. Up to two ERM units can be connected. Depending on the load, one ERM can extend the available UPS runtime by up to 15 - Compaq R6000 | HP Uninterruptible Power System R6000 Models Installation Instruc - Page 8
to charge before putting the UPS into service. IMPORTANT: The battery modules charge to: • 90% of their capacity within 3 hours • 100% of their capacity within 48 hours Charge the batteries for at least 24 hours before supplying backup power to the devices. Placing the UPS in Operate Mode Press
HP CONFIDENTIAL Writer: Kerri Morgan Codename:Arcuda
hp uninterruptible
power system R6000
models
installation instructions
Read instructions completely before beginning
installation procedure.
© 1999, 2002 Hewlett-Packard Development Company, L.P.
Hewlett-Packard Company shall not be liable for technical or editorial errors or
omissions contained herein. The information in this document is provided “as is”
without warranty of any kind and is subject to change without notice. The warranties
for HP products are set forth in the express limited warranty statements
accompanying such products. Nothing herein should be construed as constituting an
additional warranty.
hp uninterruptible power system R6000 models installation instructions
Second Edition (December 2002)
Part Number 347222-003
347222- 003
About This Device
These instructions show how to install an uninterruptible power
system (UPS). For detailed information about the UPS, refer to the
UPS user guide on the Power Products Documentation CD.
Important Safety Information
Before installing this product, read the
Important Safety
Information
guide included with the UPS kit.
Regulatory Compliance Identification
Numbers
For regulatory compliance certifications and identification
purposes, the UPS models are assigned a series number, also
identified on the Regulatory Compliance label located on the side
of the UPS. For certification information, always refer to the series
number EO3001.
NOTE:
The rating label on the device provides the class (A or B) of the
equipment. Class B devices have a Federal Communications Commission
(FCC) logo or FCC ID on the label. Class A devices do not have an FCC logo
or FCC ID on the label. After you determine the class of the device, refer to
the UPS user guide for complete regulatory compliance notices.
Weight
136 kg
300 lb
WARNING:
The UPS weighs 136 kg (300 lb) when fully
assembled. To prevent personal injury or damage to the
equipment:
•
Observe local occupational health and safety
requirements and guidelines for manual material
handling.
•
Obtain adequate assistance to lift and stabilize the
product during installation or removal. The UPS is
unstable when not fastened to the rails.
•
Remove the battery module to reduce the overall
weight of the product.
Position
WARNING: To prevent personal injury or damage to the
equipment, take the following precautions when installing the
equipment:
•
The UPS must be installed at the bottom of the rack. If
placed in the rack with existing equipment, the rack must be
reconfigured to allow installation of the UPS at the bottom
of the rack.
•
The UPS must be mounted on the rails included in the UPS
kit. Use the rack template tool included in the kit to align
the rails.