Home » Craftsman Manuals » Tools » Craftsman 21500 » Manual Viewer

Craftsman 21500 Operation Manual

Craftsman 21500 - Oscillating Spindle Sander Manual

View all Craftsman 21500 manuals

Add to My Manuals
Save this manual to your list of manuals

Craftsman 21500 manual content summary:

Craftsman 21500 | Operation Manual - Page 1
Manual Oscillating Spindle SANDER Model No. 351.215000 CAUTION: Read and follow all Safety Rules and Operating Instructions before First Use of this Product. Keep this manual with tool. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com/craftsman 25759.00 Draft (01/22/08) PARTS
Craftsman 21500 | Operation Manual - Page 2
Troubleshooting 7 Parts Illustration and List 8-9 Español 12-19 WARRANTY ONE-YEAR FULL WARRANTY ON CRAFTSMAN TOOL If this Craftsman tool Sears, Roebuck and Co., Hoffman Estates, IL 60179 SAFETY RULES WARNING: For your own safety, read all of the instructions and precautions before operating tool.
Craftsman 21500 | Operation Manual - Page 3
to operate tool until it is completely assembled according to the instructions. UNPACKING Refer to Figure 1. Check for shipping damage. If damage has occurred, a claim must be filled with carrier. Check for completeness. Immediately report missing parts to dealer. The sander comes assembled
Craftsman 21500 | Operation Manual - Page 4
not connect sander to instructions are not understood or if in doubt as to whether the tool is properly grounded. • This tool tool cords periodically, and if damaged, have repaired by an authorized service box or a properly grounded wire system. • Many cover plate screws, water pipes and outlet boxes
Craftsman 21500 | Operation Manual - Page 5
Remove the key to prevent unauthorized use. OPERATION Refer to Figures 9 and 10. DESCRIPTION The Craftsman Oscillating Spindle Sander makes sanding irregular shapes and curves in wood easy and convenient. Sander features a large 18″ cast iron table, dust port and onboard storage of durms, inserts
Craftsman 21500 | Operation Manual - Page 6
the rear side of the sander. The dust port is sized to fit the vacuum hose of Craftsman wet/dry vacuums. The use of dust collection is highly recommended. Sawdust buildup beneath the table may prevent the spindle from oscillating completely, causing damage to the tool. Figure 10 - Location of Dust
Craftsman 21500 | Operation Manual - Page 7
TROUBLESHOOTING SYMPTOM Motor will not start POSSIBLE CAUSE(S) 1. Low voltage 2. Open oscillating mechanism Excessive noise Note: Normally operating sander does make some noise Spindle Tighten spindle knob Replace sandpaper 1. Remove sawdust with vacuum 2. Inspect mechanism. Contact Sears Service
Craftsman 21500 | Operation Manual - Page 8
Model 351.215000 Figure 11 - Replacement Parts Illustration for Sander 37 22 33 39 37 37 36 40 41 42 1 2 3 4 5 6 43 66 55 47 45 46 9 57 59 58 44 45 46 47 48 49
Craftsman 21500 | Operation Manual - Page 9
PARTS LIST FOR SANDER KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 PART Bearing* 1 Bearing Retainer 1 Spindle 1 5-0.8mm Fiber Hex Nut* Base 1 Switch 1 Capacitor 1 Operator's Manual 1 Recommended Accessories Δ ¾″ Abrasive Sleeves,
Craftsman 21500 | Operation Manual - Page 10
Service Record Craftsman Oscillating Spindle Sander DATE MAINTENANCE PERFORMED REPLACEMENT PARTS REQUIRED 10
Craftsman 21500 | Operation Manual - Page 11
NOTES 11
Craftsman 21500 | Operation Manual - Page 12
, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and