Craftsman 372LM User Guide

Craftsman 372LM - Sears Lift-Master Chamberlain 315 MHz Remote Control Manual

Get Craftsman 372LM - Sears Lift-Master Chamberlain 315 MHz Remote Control PDF manuals and user guides
UPC - 753182407586
View all Craftsman 372LM manuals
Add to My Manuals
Save this manual to your list of manuals

Craftsman 372LM manual content summary:

  • Craftsman 372LM | User Guide - Page 1
    Model 372LM and 372LMC Security✚® 2-Button Remote Control The 372LM and 372LMC remote control can activate two separate 315MHz residential or commercial garage door openers and/or gate openers. The instructions for programming garage door openers are illustrated below. Please refer to the original
  • Craftsman 372LM | User Guide - Page 2
    .) Yellow Indicator Light FCC Label 5. The right button is now sending the same identical Yellow Indicator coded signal as Remote Light Control X. This code will Remote Control X remain inside the 372LM and 372LMC until replaced with another new code by repeating steps 1-4 above, or by
  • Craftsman 372LM | User Guide - Page 3
    372LM et 372LMC La télécommande 372LM et 372LMC peut actionner deux dispositifs séparés 315MHz d'ouverture de portes de garage AVERTISSEMENT AVERTISSEMENT AVERT et/ou de clôture résidentielles ou commerciales. Les instructions elle est bouton mauve «Learn». Le code dynamique transmis entre ces
  • Craftsman 372LM | User Guide - Page 4
    29B137 372LMC clignote très rapidement, ce qui signifie qu'elle a appris le code. (Si la télécommande X est également un 372LM ou 372LMC, enfoncer et retenir le bouton-poussoir droit.) Témoin lumineux jaune Télécommande X POUR LE SERVICE, PRIÈRE DE COMPOSER NOTRE NUMÉRO SANS FRAIS: US: 1-800-528
  • 1
  • 2
  • 3
  • 4
To deactivate any unwanted remote, first erase all codes:
Press and the hold “learn” button on motor unit until the learn indicator light goes out
(approximately 6 seconds). All previous codes are now erased. Reprogram each remote or
keyless entry you wish to use.
Model 372LM and 372LMC Security
✚
®
2-Button Remote Control
The 372LM and 372LMC remote control can activate two
separate 315MHz residential or commercial garage door
openers and/or gate openers.
The instructions for
programming garage door openers are illustrated below.
Please refer to the original receiver programming for
commercial and gate products.
Both push buttons are factory programmed to work with
315MHz Security
✚
®
receivers having a purple “learn”
button. The rolling code between these buttons and the
receiver changes with each use, randomly accessing over
100 billion new codes.
As an added feature, the push button on the right is
capable of learning or being trained to duplicate or match
another CGI manufactured fixed code or billion-code
remote. This feature is normally used when several
remotes are required to operate one fixed code device
such as a gate opener or commercial dock door. In this
case, the code transmitted to the receiver remains
constant or fixed, not using the Security
✚
®
format.
NOTE:
The push button on the left cannot be changed
from Security
✚
®
, only the right button is trainable.
1
2
3
1
2
1.Press and release the “learn” button
on the motor unit. The learn
indicator light will glow steadily for
30 seconds.
2. Within 30 seconds, press and hold
the button on the hand-held remote
that you wish to operate your
garage door.
3. Release the button when the motor
unit light blink. It has learned the
code. If light bulbs are not installed,
two clicks will be heard.
2
3
1
KG
KG
Instructions are described and illustrated below.
Figure 1
Right
Push Button
(Multi-use)
2
3
1
KG
KG
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
To prevent possible SERIOUS INJURY or DEATH from a
moving gate or garage door:
• ALWAYS keep remote controls out of reach of children.
NEVER permit children to operate, or play with remote
control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to door
travel.
• ALWAYS keep gate or garage door in sight until completely
closed. NEVER permit anyone to cross path of moving gate
or door.
WARNING
To Erase All Codes From Motor Unit Memory