Cub Cadet PRO Z 972 SDL Operation Manual
Cub Cadet PRO Z 972 SDL Manual
 |
View all Cub Cadet PRO Z 972 SDL manuals
Add to My Manuals
Save this manual to your list of manuals |
Cub Cadet PRO Z 972 SDL manual content summary:
- Cub Cadet PRO Z 972 SDL | Operation Manual - Page 1
Practices • Set-Up • Operation • Service • Troubleshooting Operator's Manual Pro Z 900 Series Steering Wheel Table of INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. NOTE: This Operator's Manual - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 2
and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in safety signs. 3. All operators and mechanics should be trained to operate or service the equipment. The owner is responsible for training them. 4. Never let - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 3
which are not covered in this manual use care and good judgement. Contact your customer service representative for assistance. Slope Operation Children 16 and over should read and understand the instructions and safe operation practices in this manual and on the machine and should be trained and - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 4
Towing 1. Do not tow heavy tow-behind attachments (e.g. loaded dump cart, lawn roller, etc.) on slopes greater than 5 degrees. 2. Tow only with a machine that has a hitch designed for towing. Do not attach towed equipment except at the hitch point. 3. Follow the manufacturer's recommendation for - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 5
this manual. If the safety interlock system does not function properly, have your machine serviced. the engine. 14. Maintain or replace safety and instruction labels, as necessary. 15. Observe proper disposal laws canister. Please contact Customer Support for information regarding the evaporative - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 6
on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR'S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate WARNING - ROTATING BLADES Do not put hands or feet near rotating parts or - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 7
Figure 1 and Figure 2). 5. If there is a gap below the gauge, the slope is too steep for safe operation (See Figure 2 above). Use this page as a guide to determine slopes where you may not operate safely. WARNING DO not operate your lawn mower on such slopes. Do not mow on inclines with - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 8
. Please read this entire manual prior to operating the equipment. It instructs you how to safely and problems or questions concerning the machine, phone your local authorized service dealer or contact us directly. We want to ensure your complete satisfaction at all times. Throughout this manual - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 9
and secure the seat into place with the hardware as shown in Figure 2-7. 3. Remove the shoulder screw (a) and flange lock nut (b) from manual bag and install the seat lockout bracket (c) as shown in Figure 2-8. (b) (a) (c) Figure 2-8 4. Insert the wiring harness (a) into the bottom of the seat - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 10
under the seat on the right side (see a in Figure 2-14). On SDL models it is located prominently on the right side ( see b in Figure 2-14 when the seat is in the desired position. See Figure 2-14. To vary the lumbar support (700 and 900 series) move the lever on the right of the seat up and down - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 11
prop. Remove the bolts and hex nuts from the manual bag. Note: The positive battery terminal is marked SD models follow the instructions below in (a). For SDL Models follow the instructions below in (b): a. 2-22. Note: If the battery is put into service after the date shown on top/side of battery, - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 12
of the actual hours of operation to assure all maintenance procedures are completed according to the instructions in this Operator's Manual and the Engine Operator's Manual. The hour meter and service minder is equipped with a MODE button that can toggle between available functions and can be used - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 13
Assembly & Set-Up section for instructions on adjusting the lumbar support. Self-Leveling Seat (Not Shown, the operators seat on SD models. For SDL models, the latch is located on either side models. See the Product Care section of this manual for more information on the transmission oil expansion - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 14
receptacles (SD models) or one receptacle (SDL models) for optional accessories are on the Check the engine oil level as instructed in the Engine Operator's manual. 5. Check the transmission oil , refer to the Service section. 10. Lubricate all pivot points listed in the Service section. 11. Adjust - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 15
Fuel Injection) Engines section. Manual Throttle/Choke or Throttle/Automatic noise persists, take the tractor to your authorized service dealer. Cold Weather Starting When starting the engine Refer to the Assembly & Set-Up section for instructions on adjusting the seat. 4. Adjust the steering wheel - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 16
WARNING Always maintain a firm grip on the steering wheel. 7. To drive the tractor, firmly grasp the steering wheel with your right and left hands and continue with Driving the Tractor Forward. Driving the Tractor Forward WARNING Keep all movement of the drive pedals slow and smooth. Abrupt movement - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 17
1. Use the deck lift pedal (a) or push down on the back of the electric deck lift switch (b) to raise the deck to its highest position, place the clevis pin (c) attached to the tractor into the desired index hole on the deck height index, then slowly release the deck lift pedal (a) or slowly lower - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 18
Standard set-up Stems (Dandelion, Bahia, Buckhorn, etc.) Very Lush &/or tall grass Low cut height (1 to 2") Mulch Material collection Abrasive (sandy), dry Wet Reconfigurable Mower Inner Baffle Installed Removed Removed Installed Installed Installed Removed Installed Discharge Baffle Installed - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 19
Product Care Maintenance Schedule Check gasoline level Check hydraulic hoses for leaks Check tires & tire pressure Check deck, mower and hydro drive belts Check blades and blade bolt tightness Check safety switches for proper operation Check fluid level in transmission oil expansion reservoir Check/ - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 20
Lid Hinges (If Mower is so equipped) Engine Oil • Shell Rotella® T Triple Protection™ 15W40 • Shell Rimula® 15W40 • Reference your engine manual for other approved options Hydrostatic Fluid • Drive System Fluid Plus (Shell TT-SB) • Castrol™ (Syntec®) Edge™ 5W50 General Purpose Lubrication: Use - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 21
skin. Exercise caution to avoid burns. Maintain oil level as instructed in Engine Operator's Manual. Be careful not to spill oil on any of the belts been run flat or seriously under inflated. Have it inspected and serviced by a qualified tire mechanic. Battery Information WARNING Should battery acid - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 22
battery by repeating the above steps in the reverse order. Removing the Battery (SDL Models) 1. Flip the seat all the way forward. 2. Remove the hex transmissions are equipped with a bypass rod that will allow you to manually move the tractor short distances. WARNING Do not tow the tractor, - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 23
the instructions provided in the Engine Operator's Manual packed with this manual. WARNING cause serious starting problems. • Read the product manufacturer's instructions and recommendations. • will result in shortened life and reduce serviceability. Removing The Tractor From Storage 1. Check - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 24
tractor following the normal starting instructions previously provided; then disconnect the seat switch must be replaced. See your authorized service dealer. With the drive pedals in the neutral This electric clutch is a normally trouble free device. If a problem develops and the blades do not - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 25
right side of the mower and remove. 9. To install reverse the process. Replacing the PTO Belt 1. Remove the PTO belt (a) from the deck as instructed in the Deck Removal section then remove it from around the PTO clutch. See Figure 4-22. (a) (b) (d) (c) Figure 4-22 2. Route the PTO belt (a) as shown - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 26
the key from the switch. Protect your hands by using heavy gloves when handling the blades. When servicing the mower deck, be careful not to cut yourself on the sharpened blades. 1. Remove the deck as instructed in the Deck Removal section on page 24. 2. For easier access, flip the deck over, then - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 27
assemblies (d) and the support plates (f) to the deck shell (g). See Figure 4-29. Note: The deck support plate (h) does not If your mower creeps, see your authorized service dealer. Troubleshooting Excessive vibration 1. Cutting blade loose or Engine Operator's Manual. Section 4 - Product Care 27 - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 28
Replacement Parts 5 Part Number Description 954-04327 954-04319 Deck Belt (54" Decks) Deck Belt (60/72" Decks) 954-05127 954-05128 954-05129 PTO Belt (54" Deck) PTO Belt (60" Deck) PTO Belt (72" Deck) 954-05037 Drive Belt 942-04416 942-04415 942-05179 Hi-Lift Blade, 19.0 (54" Deck) Hi- - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 29
Notes 29 - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 30
30 Notes - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 31
manual for warranties covering Emission Control Systems. Scope of the Limited Warranty Cub Cadet Rotary Spreader Gas Blowers, PRO HW PRO Z 500/700/900, TANK LZ/SZ PRO Z 100, Z-Force Commercial (7) years from the date of its initial sale to an Initial Purchaser, whichever comes first. 3) The - Cub Cadet PRO Z 972 SDL | Operation Manual - Page 32
Website at www.cubcadet.ca. This limited product warranty is provided by Cub Cadet LLC and is the only product warranty provided by Cub Cadet LLC for the Product. A COPY OF YOUR SALES RECEIPT IS REQUIRED FOR WARRANTY SERVICE. What This Limited Warranty Does Not Cover This limited warranty does not
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
 |
 |
Safe Operation Practices • Set-Up • Operation • Service • Troubleshooting
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
O
PERATOR
’
S
M
ANUAL
Form No. 769-18490B
(October 22, 2019)
Safe Operation Practices
........................................
2
Assembly & Set-Up
..................................................
8
Controls & Operation
.............................................
12
Product Care
...........................................................
19
Replacement Parts
................................................
28
Attachments & Accessories
..................................
28
Warranty
.................................................................
31
Table of Contents
NOTE:
This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to all
models and the model depicted may differ from yours.
Pro Z 900 Series
Steering Wheel