Home » Cub Cadet Manuals » Lawn Mowers » Cub Cadet RZT L 50 KH » Manual Viewer

Cub Cadet RZT L 50 KH RZT L 50 KH Operator's Manual

Cub Cadet RZT L 50 KH Manual

View all Cub Cadet RZT L 50 KH manuals

Add to My Manuals
Save this manual to your list of manuals

Cub Cadet RZT L 50 KH manual content summary:

Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 1
• Service • Troubleshooting • Warranty Operator's Manual RZT L Series Tractor WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. Printed In USA CUB CADET LLC
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 2
To The Owner 1 Thank You Thank you for purchasing a Cub Cadet Zero-Turn Tractor. It was carefully engineered to provide excellent performance when properly operated and maintained. Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set up,
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 3
during machine. Children 14 and over should read and understand operation and while performing an adjustment or repair the instructions and safe operation practices in this manual to protect your eyes. Thrown objects which ricochet can and on the machine and should be trained and supervised
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 4
in this manual, use care and good judgment. Contact your customer service representative for serious injury could result. 20. Slow down before turning. Operate the machine smoothly. Do: Avoid erratic operation , understand 5. and follow all instructions provided with the approved accessory or
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 5
in watchful care of a responsible adult other than the operator. b. Be alert and turn machine off if a child enters the area. c. To avoid back-over accidents, instructions and safe operation practices in this manual and on the machine and should be trained and supervised by an adult. Service Safe
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 6
. Never tamper listed in this manual. "Use of parts which do 13. Maintain or replace safety and instruction labels, as necessary. may include the Safety Commission Customer Support for information regarding machine inspected annually by an authorized service dealer to ensure that all mechanical and
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 7
on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR'S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate WARNING- ROTATING BLADES Do not put hands or feet near rotating parts or
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 8
8 Slope Gauge Section 2 - Safe Operation Practices (OK) Figure 1 15° Slope (TOO STEEP) Figure 2 15° Slope 15° dashed line USE THIS SLOPE GAUGE TO DETERMINE IF A SLOPE IS TOO STEEP FOR SAFE OPERATION! To check the slope, proceed as follows: 1. Remove this page and fold along the dashed line.
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 9
Assembly & Set-Up 3 Contents of Crate • One RZT L Tractor • One Tractor Operator's Manual • One Oil Drain Tube • One Engine Operator's Manual • One Deck Wash Hose Coupler • One Hardware Pack NOTE: This Operator's Manual covers several models. Tractor features may vary by model. Not all features
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 10
the positive battery terminal to help protect it from corrosion. NOTE: If the battery is put into service after the date shown on top/side of battery, charge the battery as instructed in the Maintenance section your Operator's Manual prior to operating the tractor. 10 Section 2- Assembly & Set-Up
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 11
the desired position; then release the adjustment lever. Make sure seat is locked into position before operating the tractor. See Figure 3-8. 50" Deck Shown Flange Lock Nuts Push Nuts Carriage Bolts Figure 3-8 Figure 3-6 3. Install the discharge chute deflector using the carriage bolts, push
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 12
Rod NOTE: This Operator's Manual covers several models. Tractor features may vary by model. Not all features in this manual are applicable to all tractor , and will take some practice to master. Refer to Operation for instructions on using the control levers. Deck Height Index The deck height index
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 13
by hand. Refer to the Assembly & Set-Up section for instructions on using the bypass feature. CAUTION: Never tow your tractor. Towing tank. Push the cap downward on the fuel tank fill neck and turn approximately 1⁄4 turn clockwise to tighten. Always re-install the fuel cap tightly onto the
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 14
the instructions in this manual and the engine manual. When key is turned to five minutes after every 50 hours of recorded operation. The maintenance interval lasts for two hours (from 50-52, 100-102, for possible causes and/or contact your Cub Cadet dealer. Oil Pressure Indicator (If Engine
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 15
INSTRUCTION - Entirely read this operator's manual Wait for all movement to stop before servicing or cleaning. • Operate the drive control Slow down before turning and come to a complete stop before any zero turn maneuver. • Do the tractor. Contact your authorized Cub Cadet Dealer. • The safety
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 16
Insert the key into the ignition switch and turn the key clockwise to the start position and release . Have the tractor inspected by your Cub Cadet dealer. Cold Weather Starting When starting disabled tractor following the normal starting instructions previously provided; then disconnect the jumper
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 17
conventional type riding tractor. Although and because a zero turn tractor is more maneuverable, getting used to operating levers are not even in the neutral position, refer to Maintenance & Adjustments for instructions to adjust the levers so that they are even. WARNING! Always maintain your
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 18
the tractor while driving forward, move the control levers as necessary so that one lever is rearward of the other. The tractor will turn in the direction of the rearward control lever. 1. To turn to the left, move the left drive control lever rearward of the right lever. See Fig. 5-4. Forward Left
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 19
in reverse, move the left drive control lever forward of the right lever. See Fig. 5-7. Executing a Zero Turn WARNING! When executing a zero turn, the tractor MUST BE STOPPED. Executing a zero turn while the tractor is moving can significantly reduce your control of the tractor and will cause
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 20
the ground speed with the control levers. 6. When approaching the other end of the strip, slow down or stop before turning. A U-turn is recommended unless a pivot or zero turn is required. 7. Align the mower with an edge of the mowed strip and overlap approximately 3". 8. Direct the tractor on each
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 21
as designed, contact you Cub Cadet dealer to have the tractor inspected. DO NOT operate the tractor if any safety circuit is not functioning properly. To check the safety circuits, proceed as follows: 1. Pull the PTO switch upward to the engaged position. Momentarily turn
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 22
Manual for all engine maintenance intervals, procedures, specifications and instructions. Lubrication • Using a pressure lubricating gun, lubricate the front castor wheel axles with Cub Cadet 251H EP grease after every 10 hours of service Deck Wash Nozzle Figure 6-1 Turn on the water supply. From
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 23
50 hours of operation or weekly. Keep the tires inflated to the recommended pressures. Improper inflation will shorten the tire service clips to the battery while the charger is turned on, as it can cause sparks. • bypass rod that will allow you to manually move the tractor short distances. WARNING!
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 24
instructions provided in the engine manual packed with this manual problems. b. Using a fuel stabilizer such as STA-BIL® for storage between 30 and 90 days: • Read the product manufacturer's instructions and reduce serviceability. Removing The pivot bracket. 2. While supporting the control lever to
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 25
remove, the hex bolt on the rear left deck hanger link. See Figure 6-4. 4. Using a wrench, raise or lower the left side of the deck by turning the adjustment gear. See Figure 6-4. The deck is properly leveled when both blade tip measurements are equal. Retighten the hex bolt on the front left
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 26
Adjusting the Front Gauge Wheels WARNING!: Keep hands and feet away from the discharge opening of the cutting deck. The front gauge wheels on the mower deck are an anti-scalp feature, and should not ride on the ground. The front gauge wheels should be approximately 1⁄4-1⁄2" above the ground when the
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 27
a furnace, water heater, clothes dryer, etc. 2. Service the engine as instructed in the seperate engine manual. 3. Engines stored between 30 and 90 days need one ounce of oil into each cylinder. Crank the engine one or two turns to spread the oil evenly on the cylinder walls. Replace the spark plugs
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 28
Figure 7-2. Voltmeter Reading 12.7 12.4 12.2 12.0 State of Charge 100% 75% 50% 25% Charging Time Full Charge 90 Min. 180 Min. 280 Min. Hex Washer If you have a recurring problem with blown fuses, have the tractor's electrical system checked by your Cub Cadet Service Dealer. Relays and Switches
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 29
3. Pull the left side of the belt rearward and downward while manually turning the PTO pulley to the right until the belt rides out onto the belt up and over the idler pulley. See Figure 7-4. 46/50/54" Decks Moveable Idler Pulley 42" Decks Moveable Idler Pulley PTO 7-3. Section 7 - Service 29
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 30
has been routed properly. 8. Place the deck lift handle into the highest mowing position and slide the deck out from beneath the tractor. 30 Section 7- Service
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 31
Figure 7-8. Flat Washer Hex Screw Figure 7-11 NOTE: Take note of the position of the belt guard to ensure they are properly re-installed. Section 7 - Service 31
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 32
Route the belt as shown in Figure 7-10 and then reinstall the deck (refer to Deck Installation on page 30). 50" & 54" Deck 1. Remove the deck from beneath the tractor, (refer to Deck Removal on page 28). 2. Remove reinstall the deck (refer to Deck Installation on page 30). 32 Section 7- Service
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 33
turn the ignition key to the "OFF" position and remove the key from the switch. Protect your hands by using heavy gloves when handling the blades. When servicing to change the tractor's transmission drive belt. See your Cub Cadet dealer to have the transmission drive belt replaced. Tractor Creeping
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 34
Troubleshooting Problem Excessive vibration Uneven cut Mower will not mulch grass (If Equipped w/Mulching Kit) Cause 1. Cutting blade loose or unbalanced. 2. Damaged or bent cutting blade. 1. Deck
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 35
918-04125B 618-06978 Deck Spindle, RZT L42 Deck Spindle, RZT L46 Deck Spindle, RZT L50 Deck Spindle, RZT L54 734-04155 Deck Wheel 925-1707D Battery 951-12179B Fuel Tank Cap Phone (800) 965-4CUB to order replacement parts or a complete Parts Manual (have your full model number and serial
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 36
., RZT L50 Discharge Chute Assy., RZT L54 634-04293-0931 Wheel Assembly, RZT L42/46 634-04128-0931 Wheel Assembly, RZT L50 & RZT L54 634-04212B 634-04711 Caster Wheel Assy., RZT L42 Caster Wheel Assy., RZT L46/50/54 Phone (800) 965-4CUB to order replacement parts or a complete Parts Manual (have
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 37
and accessories are compatible with your Cub Cadet RZT L tractor. See your Cub Cadet dealer or the retailer from which you 22216 42" & 46" Bagger w/ Weight Kit 50" Bagger w/ Weight Kit 54" Twin Bagger w/ Weight Kit 42" Mulch Kit 46" Mulch Kit 50" Mulch Kit 54" Mulch Kit Rear Engine Guard
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 38
manual problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question regarding your warranty coverage, you should contact the MTD Consumer Group Inc Service Department at 1-800-800-7310 or at http://support written instructions
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 39
10. Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted add-on or modified parts by the ultimate purchaser will be grounds for disallowing a warranty claims. MTD Consumer Group Inc will not be liable to warrant failures of warranted
Cub Cadet RZT L 50 KH | RZT L 50 KH Operator's Manual - Page 40
CUB CADET LLC MANUFACTURER'S LIMITED WARRANTY FOR RESIDENTIAL ZERO-TURN ("RZT") MOWERS IMPORTANT: To obtain warranty coverage owner must present an original proof of purchase and applicable maintenance records to the servicing dealer. Please see the operator's manual for information on required