CyberPower BRG1000AVRLCD Function Setup Guide

1

2

FUNCTION SETUP GUIDE

BRG850/1000/1350/1500AVRLCD

K01-0000352-00

Power On:

Press the POWER button for approximately 2 seconds and you will hear a short

steady tone (1 second). Release the button after a short beep.

Power Off:

Press the POWER button for approximately 2 seconds and you will hear a short

steady tone (1 second). Release the button after 2 short beeps.

(

DISPLAY Button

)

:

(1) (

): Short press the button to scroll down the function / option menu and view the

information about the UPS.

(2) LCD On/Off: The default setting is the off position. The LCD display will dim if the buttons

are not touched in 60 seconds. In Line Mode, press the button for 2 seconds to keep the LCD

display always on. The LCD display will illuminate (and beep once). Press the button again

for 2 seconds to turn off the LCD display. The LCD display will be off (and beep twice).

In battery mode, the LCD is always on regardless of the settings.

(MUTE Button):

(1) (

)

:

Short press the button to scroll up the function / option menu and view the information about the UPS.

(2) Audible Alarm: Press the button for 2 seconds to enable the audible alarm (beeps once) or disable (beeps twice) the audible alarm.

The MUTE icon will appear on the LCD display when the audible alarm is disabled.

Note: The default setting for the alarm is the on position.

ENTER (SETUP Button):

Setup Mode: Press the button for 2 seconds to access the setup mode’s 9 functions: Utility Power, MAX O/P Voltage, MIN O/P Voltage,

Sensitivity, Low Battery Warning, Self Test, Event Reset, Return to Default Settings, and Return to Status Display.

Short press the button (

) or (

) to view the functions. When a function is selected, short press the ENTER button to access the

function’s options.

Short press the button (

) or (

) to view the options. When the desired option is selected, short press the ENTER button to

confirm the setting.

Note: If there is no action for 8 seconds during setup, the LCD will leave setup mode and go back to the status display. The setting will

not be confirmed.

DISPLAY + SETUP Button:

Pressing both buttons at the same time for 2 seconds will clear the EVENT counter (and beep twice).

You can also clear the EVENT counter in setup mode.

Refer to the following table for a detailed list of functions and their description.

Function

LCD Display

Options

Default

Description

Utility Power

(CUS)*

* Custom Setting: Only

when MIN or MAX O/P

Voltage is configured.

Poor (97V~135V)

Normal (100V~132V)

Good (103V~129V)

Escape to

Function

Menu

Normal

This function determines how the

UPS will switch to AVR or Battery

Mode.

3 different output voltage ranges

can be chosen according to the

quality of the AC utility service in

your location.

If your utility service is not stable,

you can select Poor (97V~135V).

The UPS will go to AVR or Battery

Mode less often to tolerate the

utility power fluctuations.

If your utility service is stable, you

can select Good (103V~129V). The

unit will go to AVR or Battery Mode

more often.

MAX O/P Voltage

*

= fine tune the

MAX O/P voltage

H129~H135

Escape to

Function

Menu

H132

In Utility Power settings, only 3

types of fixed voltage ranges can

be selected. However, you can fine

tune the MAX O/P voltage with this

option.

If the utility voltage is usually high

and the connected equipment can

work in this condition, you can set

the output voltage range higher to

reduce how often the UPS goes to

AVR Mode or Battery Mode.

MIN O/P Voltage

*

= fine tune the MIN

O/P voltage

L97~L103

Escape to

Function

Menu

L100

In Utility Power settings, only 3

types of voltage ranges can be

selected. However, you can fine

tune the MIN O/P voltage with this

option.

If the utility voltage is usually low

and the connected equipment can

work in this condition, you can set

the output voltage range lower to

reduce how often the UPS goes to

AVR Mode or Battery Mode.