CyberPower BRG1000AVRLCD User Manual

BRG850AVRLCD

BRG1000AVRLCD

User’s Manual

K01-0000351-03

Thank you for purchasing a CyberPower product. Please take a few minutes to register your product at

CyberPowerSystems.com/registration.

Registration certifies your product's warranty, confirms your ownership in the event of a

product loss or theft and entitles you to free technical support. Register your product now to receive the benefits of CyberPower

ownership.

(SAVE THESE INSTRUCTIONS)

This Manual Contains Important Instructions that should be followed during Installation and Maintenance of the UPS and batteries.

CAUTION!

To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of

conductive contaminants.

(Please see specifications for acceptable temperature and humidity range).

CAUTION!

To reduce the risk of electric shock, do not remove the cover except to service the battery. Turn off and unplug the unit

before servicing the batteries. There are no user serviceable parts inside except for the battery.

CAUTION!

Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected.

CAUTION!

The

UPS must be connected to an AC power outlet with fuse or circuit breaker protection.

Do not plug into an outlet

that is not grounded.

If you need to de-energize this equipment, turn off and unplug the unit.

CAUTION!

To avoid electric shock, turn off the unit and unplug it from the AC power source before servicing the battery.

CAUTION!

Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing

Equipment, ANSI/NFPA 75.

CAUTION!

To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum branch circuit over current

protection in accordance with the National Electric Code, ANSI/NFPA 70.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT!

CyberPower Systems does not sell products for life support or medical

applications.

DO NOT

use in any circumstance that would affect the operation and safety of life support equipment, medical

applications, or patient care.

DO NOT USE WITH OR NEAR AQUARIUMS!

To reduce the risk of fire or electric shock, do not use with or near an aquarium.

Condensation from the aquarium can cause the unit to short out.

DO NOT USE THE UPS ON ANY TRANSPORTATION!

To reduce the risk of fire or electric shock, do not use the unit on any

transportation such as airplanes or ships.

The effect of shock or vibration caused during transit and the damp environment can cause

the unit to short out.

INTRODUCTION

Thank you for selecting a CyberPower Systems UPS product. This UPS is designed to provide unsurpassed power protection, operation

and performance during the lifetime of the product.

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

(a) UPS (b) User’s manual (c) USB A+B type cable (d) Function Setup Guide

*PowerPanel® Personal software is available as a free download at:CyberPowerSystems.com/products/software.

OVERVIEW

The

BRG850AVRLCD/BRG1000AVRLCD provides complete power protection from utility power that is not always consistent. The

BRG850AVRLCD/BRG1000AVRLCD features 1080 Joules of surge protection. Both units provide long lasting battery backup during

power outages with maintenance free batteries. The BRG850AVRLCD/BRG1000AVRLCD ensures consistent power to your computer

system and includes software that will automatically save your open files and shutdown your computer system during a utility power

loss.

AUTOMATIC VOLTAGE REGULATOR

The

BRG850AVRLCD/BRG1000AVRLCD

stabilizes inconsistent utility power voltage to nominal

levels that are safe for equipment. Inconsistent incoming utility power may be damaging to

important data files and hardware, but with Automatic Voltage Regulation (AVR),

damaging

voltage levels are corrected to safe levels.

AVR automatically increases low utility power or

decreases high utility power to a consistent and safe 110/120 volts.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1.

Ensure that the equipment plugged into the outlet does not exceed the UPS’s rated capacity (850VA/510W for BRG850AVRLCD,

1000VA/600W for BRG1000AVRLCD). If the rated capacities of the units are exceeded, an overload condition may occur and cause

the UPS to shut down or the circuit breaker to trip.

2.

There are many factors that can affect the amount of power that your computer system will require.

It is suggested that the load

placed on the battery outlets not exceed 80% of the unit’s capacity.

HARDWARE INSTALLATION GUIDE

1.

Your new UPS may be used immediately upon receipt. However, after receiving a new UPS, to

ensure the battery’s maximum charge capacity, it is recommended that you charge the battery for

at least 8 hours. Your UPS is equipped with an auto-charge feature. When the UPS is plugged into

an AC outlet, the battery will automatically charge whether the UPS is turned on or off.

2.

Note: This UPS is designed with a safety feature to keep the system from being turned on during

shipment. The first time you turn the UPS on, you will need to have it connected to AC power or it

will not power up.

3.

With the UPS unit turned off and unplugged, connect your computer, monitor, and any other

peripherals requiring battery backup

into the battery power supplied outlets.

DO NOT plug a laser printer, paper shredder, copier, space

heater, vacuum, sump pump or other large electrical devices into the “Battery and Surge Protected

Outlets”. The power demands of these devices may overload and damage the UPS.

4.

Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet).

Make sure the wall branch

outlet is

protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. air

conditioner, copier, etc…).

The warranty prohibits the use of extension cords, outlet strips, and surge strips.

5.

Press the power switch to turn the unit on.

The Power On indicator light will illuminate and the unit will “beep”.

If an overload is detected, an audible alarm will sound and the unit will emit one long beep.

To correct this, turn the UPS off and

unplug at least one piece of equipment from the battery power supplied outlets.

Make sure the circuit breaker is depressed and

then turn the UPS on.

6.

To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

7.

To store the UPS for an extended period, cover it and store with the battery fully charged.

While in storage, recharge the battery

every three months to ensure battery life.

8.

Ensure the wall outlet and UPS are located near the equipment being attached for proper accessibility.

DESCRIPTION

1

Power Switch

Used as the master on/off switch for equipment connected to the battery power supplied outlets.

2

Power On Indicator

This LED is illuminated when the utility power is normal and the UPS outlets are providing power, free of surges and spikes.

3

LCD module display

The LCD display shows all the UPS information using icons and messages.

For more information please review the “Definitions

for Illuminated LCD Indicators” section below.

4

Down/Display Button

The button can be used to select the LCD display contents including Input Voltage, Output Voltage, and Estimated Run Time.

Short press the button to scroll down the function menu. Pressing the button for 2 seconds will keep the LCD display always on

or turn the LCD display off while in AC/Utility power mode. For more information about the Down/Display Button, please refer to

the

Function Setup Guide.

5

Up/Mute Button

Short press the button to scroll up the function menu. Holding the button for more than 2 seconds will silence the alarm. For

more information about the Up/Mute Button, please refer to the


6

Enter/Setup Button

Press the button for 2 seconds to enter the setup menu and then select the functions for configuration. For more information

about the Enter/Setup Button, please refer to the


7

USB Charging Ports

The USB Charging ports provide 5V 2.1A power output.

8

Battery and Surge Protected Outlets

The UPS has five battery powered/surge suppression outlets for connected equipment to ensure temporary uninterrupted

operation of your equipment during a power failure.

(DO NOT plug a laser printer, paper shredder, copier, space heater,

vacuum, sump pump or other large electrical devices into the “Battery and Surge Protected Outlets”. The power demands of

these devices may overload and damage the unit.)

9

Full-Time Surge Protection Outlets

The UPS has five surge suppression outlets to provide protection against surges and spikes.

10

Circuit Breaker

Located on the back of the UPS, the circuit breaker provides overload and fault protection.

11

Serial/USB Ports to PC

The USB port allows connection and communication between the USB port on the computer and the UPS.

12

Communication Protection Ports

Communication protection ports bi-directional, will protect a 10/100/1000 Ethernet connection (RJ45).

13

Wiring Fault Indicator (red)

This LED indicator will illuminate to warn the user that a wiring problem exists, such as bad ground, missing ground or reversed

wiring.

If this is illuminated, disconnect all electrical equipment from the outlet and have an electrician verify the outlet is

properly wired. The UPS will not provide surge protection without being plugged into a grounded and properly wired wall outlet.

14

Coax/Cable/DSS Surge Protection

The Coax/Cable/DSS protection ports will protect any cable modem, CATV converter, or DSS receiver.

REPLACING THE BATTERY

Replacement of batteries located in an

OPERATOR ACCESS AREA

.

1.

When replacing batteries, replace with the same number of the following battery: CyberPower / RB1280A for the BRG850AVRLCD

and CyberPower / RB1290 for the BRG1000AVRLCD.

2.

CAUTION!

Risk of Energy Hazard, 12V, maximum 9 Ampere-hour battery. Before replacing batteries, remove conductive jewelry

such as chains, wrist watches, and rings. High energy conducted through these materials could cause severe burns.

3.

CAUTION!

Do not dispose of batteries in a fire. The batteries may explode.

4.

CAUTION!

Do not open or mutilate batteries. Released material is harmful to the skin and eyes. It may be toxic.

5.

CAUTION:

A battery can present a risk of electrical shock and high short circuit current. The following precautions should be

observed when working on batteries:

1) Remove watches rings, or other metal objects.

2) Use tools with insulated handles.

CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO

LOCAL REGULATIONS.

BATTERY REPLACEMENT PROCEDURE:

1.

Turn off and unplug all connected equipment.

2.

Turn the UPS off and unplug it from the AC power source.

3.

Turn the UPS on its side.

4.

Remove the front panel retaining screws located on the bottom of the UPS.

5.

Slide the battery compartment cover (front panel) completely off of the unit.

6.

Disconnect the battery wires from the battery.

7.

Remove the battery from the compartment.

8.

Put the battery back into the compartment.

9.

Install the replacement battery by connecting the red wire (+) and black wire (-) to the same color connectors from the battery

pack.

10.

Slide back the battery compartment cover and tighten the retaining screws.

11.

Recharge the UPS for 8-16 hours to fully charge the battery.

REMINDER:

Batteries are considered

HAZARDOUS WASTE

and must be disposed of properly.

Most retailers that sell lead-acid

batteries collect used batteries for recycling, as required by local regulations.

1.

ONLINE:

The UPS is supplying utility power to connected equipment.

2.

BATTERY:

During a severe brownout or blackout, this icon appears and an alarm

sounds (two short beeps followed by a pause) to indicate the UPS is operating from

its internal batteries. During a prolonged brownout or blackout, the alarm will beep

rapidly every 1/2 second to indicate the UPS’s batteries are nearly out of power. You

should save files and turn off your equipment immediately or allow the software to

shut the system down.

3.

Energy-Saving:

The UPS is in energy-saving bypass mode. See “CyberPower

GreenPower UPS

TM

Technology” section for more information.

4.

LOAD capacity / Sensitivity setup:

LOAD capacity: This meter displays the

approximate output load level (in 20% increments) of the UPS battery outlets.

Sensitivity setup:

This meter is also used to setup the UPS sensitivity when you are in

the programming mode. If the connected equipment can tolerate more power events (example: unstable power often associated

with stormy weather), select Low Sensitivity and the UPS will go to Battery Mode less often. If the connected equipment is more

sensitive to power events, select High Sensitivity and the UPS will go to Battery Mode more often.

5.

BATTERY capacity:

This meter displays the approximate charge level (in 20% increments) of the UPS’s internal battery. During a

blackout or severe brownout, the UPS switches to battery power, the BATTERY icon appears, and the charge level decreases.

6.

FAULT:

This icon appears if there is a problem with the UPS. Press the POWER button to turn the UPS off.

F01: Battery Mode or AC/Utility Power Mode Overload fault

(Unplug at least one piece of equipment from battery outlets and

turn the UPS on again.)

F02: Battery Output Short fault

(Unplug at least one piece of equipment from battery outlets and turn the UPS on again.)

F03: Over charge or Charger Fail

(Contact CyberPower Systems for support.)

F04: Over temperature

(Contact CyberPower Systems for support.)

7.

OVER LOAD:

This icon appears and an alarm sounds to indicate the battery-supplied outlets are overloaded. To clear the

overload, unplug one piece of equipment from the battery-supplied outlets at a time until the icon turns off and the alarm stops.

8.

SCHEDULE:

Users can setup the schedule to turn on and shut down the computer and UPS through PowerPanel

®

Personal Edition

software. The LCD display will show how much time is left before the UPS will turn back on or shut down.

9.

ESTIMATED RUNTIME:

This displays the run time estimate of the UPS with current battery capacity and load.

10.

OUTPUT Meter:

This meter measure, in real time, the AC voltage that the UPS system is providing to the computer, such as

normal AC line mode, AVR mode, and battery backup mode. (Note: The OUTPUT meter shows the status of the battery backup

outlets in terms of load, frequency, and voltage.)

11.

INPUT Meter:

This meter measures the AC voltage that the UPS system is receiving from the utility wall outlet. The UPS is

designed, through the use of automatic voltage regulation, to continuously correct output voltage to connected equipment to a

safe 110/120 voltage output range. In the event of a complete power loss, severe brownout, or over-voltage, the UPS relies on

its internal battery to supply consistent 110/120 output voltage. The INPUT voltage meter can be used as a diagnostic tool to

identify poor-quality input power.

12.

EVENT:

This meter records the number of power outages.

13.

MUTE:

This icon appears whenever the UPS is in silent mode. However, when there is a problem with the UPS, the alarm will still

beep even in silent mode.

14.

AVR (Automatic Voltage Regulation):

This icon appears whenever your UPS is automatically correcting low or high AC line

voltage without using battery power. This is a normal, automatic operation of your UPS, and no action is required on your part.

For more information about functions setup, please refer to the

Function Setup Guide

.

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

IMPORTANT SAFETY INSTRUCTIONS

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

PRODUCT REGISTRATION

11

13

10

9

8

14

12

2

1

3

7

4

6

5

CyberPower BRG1000AVRLCD User Manual

CyberPower BRG1000AVRLCD Manual

CyberPower BRG1000AVRLCD manual content summary: