CyberPower CP1500AVRLCD3 User Manual

SERIAL

COAX

REFER TO

BOTTOM OF

UNIT FOR

ELECTRICAL

CAUTIONS

YOUR ULTIMATE ALLY IN POWER

CP1350/1500AVRLCD3

USER MANUAL

Cyber Power Systems (USA), Inc.

4241 12th Avenue East, Suite 400 | Shakopee, MN 55379 | CyberPowerSystems.com

IMPORTANT SAFETY WARNINGS

(SAVE THESE INSTRUCTIONS)

When using electrical appliances, basic safety precautions should always be followed to

reduce the risk of fire, electric shock, and/or injury to persons including the following. This

Manual Contains Important Instructions that should be followed during installation and

maintenance of the UPS and batteries.

CAUTION!

To prevent the risk of fire or

electric shock, install in a temperature

and humidity controlled indoor area free

of conductive contaminants.

(Please see

specifications for acceptable temperature

and humidity range).

CAUTION!

To reduce the risk of electric

shock, do not remove the cover except to

service the battery. Turn off and unplug the

unit before servicing the batteries. There

are no user serviceable parts inside except

for the battery.

CAUTION!

Hazardous live parts inside can

be energized by the battery even when the

AC input power is disconnected.

CAUTION!

The UPS must be connected

to an AC power outlet with fuse or circuit

breaker protection. Do not plug into an

outlet that is not grounded. If you need to

de-energize this equipment, turn off and

unplug the unit.

CAUTION!

To avoid electric shock, turn off

the unit and unplug it from the AC power

source before servicing the battery.

CAUTION!

Not for use in a computer

room as defined in the Standard for the

Protection of Electronic Computer/Data

Processing Equipment, ANSI/NFPA 75.

CAUTION!

To reduce the risk of fire,

connect only to a circuit provided with

20 amperes maximum branch circuit over

current protection in accordance with the

National Electric Code, ANSI/NFPA 70.

DO NOT USE FOR MEDICAL OR LIFE

SUPPORT EQUIPMENT!

CyberPower

Systems does not sell products for life

support or medical applications.

DO NOT

use in any circumstance that would affect

the operation and safety of life support

equipment, medical applications, or patient

care.

DO NOT USE WITH OR NEAR

AQUARIUMS!

To reduce the risk of fire

or electric shock, do not use with or near

an aquarium.

Condensation from the

aquarium can cause the unit to short out.

DO NOT USE THE UPS ON ANY

TRANSPORTATION!

To reduce the risk of

fire or electric shock, do not use the unit

on any transportation such as airplanes

or ships. The effect of shock or vibration

caused during transit and the damp

environment can cause the unit to short

out.

INSTALLING YOUR UPS SYSTEM

UNPACKING

Inspect the UPS upon receipt.

The box should contain the following:

(a) UPS

(b) User’s manual

(c) USB A+B type cable

(d) Function Setup Guide

*PowerPanel® Personal software is

available on our website. Please visit

cyberpowersystems.com and go to the

Software Section for free download.

OVERVIEW

The CP1350/1500AVRLCD3 provides

complete power protection from utility

power that is not always consistent. The

CP1350/1500AVRLCD3 features 1500

Joules of surge protection. The unit

provides long lasting battery backup

during power outages with maintenance

free batteries. The CP1350/1500AVRLCD3

ensures consistent power to your computer

system and includes software that will

automatically save your open files and

shutdown your computer system during a

utility power loss.

AUTOMATIC VOLTAGE REGULATOR

The CP1350/1500AVRLCD3 stabilizes

inconsistent utility power voltage to

nominal levels that are safe for equipment.

Inconsistent incoming utility power may

be damaging to important data files and

hardware, but with Automatic Voltage

Regulation (AVR), damaging voltage

levels are corrected to safe levels.

AVR

automatically increases low utility power

to a consistent and safe 110/120 volts.

DETERMINE THE POWER REQUIREMENTS

OF YOUR EQUIPMENT

1 . Ensure that the equipment plugged into

the outlet does not exceed the UPS’s

rated capacity. If the rated capacity

of the unit is exceeded, an overload

condition may occur and cause the UPS

to shut down or the circuit breaker to

trip.

2 . There are many factors that can

affect the amount of power that your

computer system will require. It is

suggested that the load placed on the

battery outlets not exceed 80% of the

unit’s capacity.

REMINDER:

Batteries are considered

HAZARDOUS WASTE

and must be disposed of properly.

Most retailers that sell lead-acid batteries collect used batteries for recycling, as required by

local regulations.

K01-0000946-00

1 . Power Switch:

Used as the master on/

off switch for equipment connected to

the battery power supplied outlets.

2 . Power On Indicator:

This LED is

illuminated when the utility power

is normal and the UPS outlets are

providing power, free of surges and

spikes.

3 . LCD module display:

The LCD

display shows all the UPS information

using icons and messages.

For

more information please review the

“Definitions for Illuminated LCD

Indicators” section.

4 . Down/Display button:

The button

can be used to select the LCD display

contents including Input Voltage,

Output Voltage, and Estimated Run

Time. Short press the button to scroll

down the function menu. Pressing the

button for 2 seconds will keep the

LCD display always on or turn the LCD

display off while in AC/Utility power

mode. For more information about the

Down/Display Button, please refer to

the Function Setup Guide.

5 . Up/Mute button:

Short press the

button to scroll up the function menu.

Holding the button for more than 2

seconds will silence the alarm. For

more information about the Up/Mute

Button, please refer to the Function

Setup Guide.

6 . Enter/Setup button:

Press the button

for 2 seconds to enter the setup menu

and then select the functions for

configuration. For more information

about the Enter/Setup Button, please

refer to the Function Setup Guide.

7 . USB Charging Ports:

The USB

Charging ports provide 5Vdc,3A

Max(USB-C), and 5 Vdc, 2.4A

Max(USB-A). Total Output Current:4A

8 . Battery and Surge Protected

Outlets:

The UPS has six battery

powered/surge suppression outlets

for connected equipment to ensure

temporary uninterrupted operation

of your equipment during a power

failure.

(DO NOT plug a laser printer,

paper shredder, copier, space heater,

vacuum, sump pump or other large

electrical devices into the “Battery

and Surge Protected Outlets”. The

power demands of these devices may

overload and damage the unit.)

9 . Full-Time Surge Protection Outlets:

The UPS has six surge suppression

outlets.

10 . Circuit Breaker:

Located on the back

of the UPS, the circuit breaker serves to

provide overload and fault protection.

11. USB Port to PC:

The USB port allows

connection and communication

between the USB port on the computer

and the UPS unit.

DB9 Port:

The DB9 port is used for

connecting between the UPS and

equipment designed to operate with a

dry contact closure.

12. Wiring Fault Indicator (red):

This LED

indicator will illuminate to warn the

user that a wiring problem exists, such

as bad ground, missing ground or

reversed wiring.

If this is illuminated,

disconnect all electrical equipment

from the outlet and have an electrician

verify the outlet is properly wired. The

UPS will not provide surge protection

without being plugged into a grounded

and properly wired wall outlet.

13 . Communication Protection Ports

(RJ45):

Communication protection

ports, bi-directional, will protect a

10/100/1000 Ethernet connection.

14 . Coax/Cable/DSS Surge Protection:

The Coax/Cable/DSS protection ports

will protect any cable modem, CATV

converter, or DSS receiver.

BASIC OPERATION

HARDWARE INSTALLATION GUIDE

1 . Your new UPS may be used

immediately upon receipt. However,

after receiving a new UPS, to ensure

the battery’s maximum charge capacity,

it is recommended that you charge the

battery for at least 8 hours. Your UPS is

equipped with an auto-charge feature.

When the UPS is plugged into an AC

outlet, the battery will automatically

charge whether the UPS is turned on or

off.

Note:

This UPS is designed with a

safety feature to keep the system from

being turned on during shipment. The

first time you turn the UPS on, you will

need to have it connected to AC power

or it will not power up.

2 .

With the UPS

unit turned off

and unplugged,

connect your

computer, monitor,

and any other peripherals requiring

battery backup into the battery power

supplied outlets.

DO NOT plug a

laser printer, paper shredder, copier,

space heater, vacuum, sump pump

or other large electrical devices into

the “Battery and Surge Protected

Outlets”. The power demands of these

devices may overload and damage the

UPS.

3 . Plug the UPS into a 2 pole, 3 wire

grounded receptacle (wall outlet).

Make sure the wall branch outlet is

protected by a fuse or circuit breaker

and does not service equipment with

large electrical demands (e.g. air

conditioner, copier, etc.).

The warranty

prohibits the use of extension cords,

outlet strips, and surge strips.

4 . Press the power switch to turn the unit

on.

The Power On indicator light will

illuminate and the unit will “beep”. If an

overload is detected, an audible alarm

will sound and the unit will emit one

long beep.

To correct this, turn the

UPS off and unplug at least one piece

of equipment from the battery power

supplied outlets.

Make sure the circuit

breaker is depressed and then turn the

UPS on.

5 . To maintain optimal battery charge,

leave the UPS plugged into an AC

outlet at all times.

6 . To store the UPS for an extended

period, cover it and store with the

battery fully charged.

While in storage,

recharge the battery every three

months to ensure battery life.

7 . Ensure the wall outlet and UPS are

located near the equipment being

attached for proper accessibility.

INSTALLING YOUR UPS SYSTEM - Continued

PLUG IN

PRODUCT REGISTRATION

Thank you for purchasing a CyberPower product. Please take a few minutes to register your product at: cyberpowersystems.com/registration. Registration certifies your product's warranty,

confirms your ownership in the event of a product loss or theft and entitles you to free technical support. Register your product now to receive the benefits of CyberPower ownership.

FEATURES

1 . Power Switch

2 . Power On Indicator

3 . LCD module display

4 . Down/Display button

5 . Up/Mute button

6 . Enter/Setup button

7 . USB Charging Ports

8 . Battery and Surge Protected Outlets

9 . Full-Time Surge Protection Outlets

10 . Circuit Breaker

1 1 . USB Port to PC/DB9 Port

12 . Wiring Fault Indicator (red)

13 . Communication Protection Ports

14 . Coax/Cable/DSS Surge Protection

3

1

4

5

6

13

7

2

11

12

10

9

14

8

Replacement of batteries located in an

OPERATOR ACCESS AREA

.

1 . When replacing batteries, replace with the same number of the following battery:

CyberPower / RB1290x2E

2 .

CAUTION!

Risk of Energy Hazard, 24 V, maximum 9 Ampere-hour battery. Before

replacing batteries, remove conductive jewelry such as chains, wrist watches, and rings.

High energy conducted through these materials could cause severe burns.

3 .

CAUTION!

Do not dispose of batteries in a fire. The batteries may explode.

4 .

CAUTION!

Do not open or mutilate batteries. Released material is harmful to the skin

and eyes. It may be toxic.

5 .

CAUTION:

A battery can present a risk of electrical shock and high short circuit current.

The following precautions should be observed when working on batteries:

1 ) Remove watches rings, or other metal objects.

2) Use tools with insulated handles.

CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO LOCAL REGULATIONS.

REPLACING THE BATTERY

BATTERY REPLACEMENT PROCEDURE

1 . Switch off and unplug all the connected equipment.

2 . Switch off the UPS and disconnect it from the wall outlet.

3 . Place the product on its side, on a solid and stable surface.

4 . Loosen the battery compartment cover screws.

5 . Press on the locking latch and slide the battery compartment cover.

6 . Using the handles on both sides of the battery pack, lift the battery pack 30 degrees

upward to expose the battery connector. Connect the wires as shown above.

7 . Replace the new battery pack into the unit and connect the wires as above steps

8 . Align the side rails on the cover with the rails on the UPS and slide the cover till it locks

and screws in position.

9 . Recharge the UPS for 8-16 hours to fully charge the battery.

(+) RED

(-) BLACK

CONNECT BATTERY

1

2

3

4

5

CyberPower CP1500AVRLCD3 User Manual

CyberPower CP1500AVRLCD3 Manual

CyberPower CP1500AVRLCD3 manual content summary: