D-Link DAP-2610 User Manual

D-Link DAP-2610 Manual

Get D-Link DAP-2610 PDF manuals and user guides View all D-Link DAP-2610 manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DAP-2610 manual content summary:

  • D-Link DAP-2610 | User Manual - Page 1
    Document Created by Nick Schuster
  • D-Link DAP-2610 | User Manual - Page 2
    D-Link DAP-2610 User Manual Table of Contents Product Overview 4 Introduction 4 Features 5 Package Contents 6 System Requirements 6 Hardware Overview 7 LEDs...7 Connections 7 Basic Installation 8 Hardware Setup 8 Method 1 - PoE with PoE Switch or Router 8 Method 2 - PoE without PoE
  • D-Link DAP-2610 | User Manual - Page 3
    D-Link DAP-2610 User Manual Login Page Upload 60 IP Filter Settings 61 MAC Bypass 62 DHCP Server 63 Dynamic Pool Settings 63 Static Pool Setting 64 Current IP Mapping List 65 Filters 66 Wireless MAC ACL 66 WLAN Partition 67 Traffic Control 68 Uplink/Downlink Setting 68 QoS 69 Traffic
  • D-Link DAP-2610 | User Manual - Page 4
    Wi-Fi Multimedia™ (WMM) Quality of Service features, makes it an ideal access point for audio, video, and voice applications. Security To help maintain a secure wireless network, the DAP-2610 provides the latest in wireless security technologies by supporting both Personal and Enterprise versions of
  • D-Link DAP-2610 | User Manual - Page 5
    D-Link DAP-2610 User Manual Features yy Provide Ethernet to Wireless LAN bridge fully IEEE for reliability, optimized throughput and transmission range yy Web-based configuration and management yy Supports 802.3af PoE yy Supports 802.3az yy Supports one Gigabit Ethernet port yy AP Mode, WDS Mode,
  • D-Link DAP-2610 | User Manual - Page 6
    D-Link DAP-2610 User Manual • DAP-2610 Access Point • Power Adapter • Mounting Plate and Hardware • Ethernet Cable Package Contents Note: Using a power supply with a different voltage rating than the one included with the DAP-2610 will cause damage and void the warranty for this product. System
  • D-Link DAP-2610 | User Manual - Page 7
    that the DAP-2610 is working properly. 2 Power Receptor Connect the supplied power adapter. 3 LAN (PoE) Port Connect to a Power over Ethernet (PoE) switch or router via an Ethernet cable. Press and hold for five seconds to reset the access point to 4 Reset Button the factory default settings
  • D-Link DAP-2610 | User Manual - Page 8
    D-Link DAP-2610 User Manual Basic Installation Hardware Setup To power the access point, you can use one of the following 3 methods: Method 1 - Use if you have a PoE switch or router. Method 2 - Use if you do not have a PoE switch or router and do not have a power outlet near the location of the
  • D-Link DAP-2610 | User Manual - Page 9
    D-Link DAP-2610 User Manual Method 2 - PoE without PoE Switch or Router 1. Connect one end of an Ethernet cable into the Data In port on the PoE base unit and the other end into one port on your switch, router, or computer. 2. Connect one end of an Ethernet cable into the P+Data Out port on the PoE
  • D-Link DAP-2610 | User Manual - Page 10
    D-Link DAP-2610 User Manual Method 3 - No PoE 1. Connect one end of your Ethernet cable into the LAN (PoE) port and then connect the other end to a switch, router, or computer. 2. Use the supplied power adapter. Connect the power adapter to the Power receptor
  • D-Link DAP-2610 | User Manual - Page 11
    D-Link DAP-2610 User Manual Web User Interface The DAP-2610 supports an elaborate web user interface where the user can configure and monitor the device. Launch a web browser, type the IP address of the access point (Default setting is http://192.168.0.50 or https://192.168.0.50) and then press
  • D-Link DAP-2610 | User Manual - Page 12
    D-Link DAP-2610 User Manual Wireless On the wireless settings page, you can setup the basic wireless configuration for the access point. Name (SSID): Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSID's factory default setting is dlink.
  • D-Link DAP-2610 | User Manual - Page 13
    D-Link DAP-2610 User Manual Channel: To change the channel, first toggle the Auto Channel Selection setting to Disable, and then use the drop-down menu to make the desired
  • D-Link DAP-2610 | User Manual - Page 14
    Link DAP-2610 User Manual WDS with AP Mode Wireless Band: Select either 2.4GHz or 5GHz from the drop-down menu. Mode: WDS with AP mode is selected from the drop-down menu. Network Name (SSID): Service Set Identifier (SSID) is the name designated for a specific wireless local is not supported in WDS
  • D-Link DAP-2610 | User Manual - Page 15
    D-Link DAP-2610 User Manual Remote AP MAC Address: Enter the MAC addresses of the APs on your network that will serve as bridges to wirelessly connect multiple networks. Site
  • D-Link DAP-2610 | User Manual - Page 16
    DAP-2610 User Manual WDS Mode Wireless Band: Select either 2.4GHz or 5GHz from the drop-down menu. Mode: WDS is selected from the drop-down menu. Network Name (SSID): Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSID's factory default
  • D-Link DAP-2610 | User Manual - Page 17
    D-Link DAP-2610 User Manual Site Survey: Click on the Scan button to search for available wireless networks, then click on the available network that you want to connect with.
  • D-Link DAP-2610 | User Manual - Page 18
    D-Link DAP-2610 User Manual Wireless Client Mode Wireless Band: Select either 2.4 GHz or 5 GHz from the drop-down menu. Mode: Wireless Client is selected from the drop-down menu. Network Name (SSID): Service Set Identifier (SSID) is the name designated for a specific wireless local area network (
  • D-Link DAP-2610 | User Manual - Page 19
    D-Link DAP-2610 User Manual Wireless Security Wireless security is a key concern for any wireless client. Shared Key will send a request to the access point and if the key used matches the one configured on the access point, the access point will send a challenge to the client. The client will then
  • D-Link DAP-2610 | User Manual - Page 20
    D-Link DAP-2610 User Manual Wi-Fi Protected Access (WPA / WPA2) WPA was created by the Wi Group Key Update: Select the interval during which the group key will be valid. The default value of 1800 is recommended. Pass Phrase: When you selectWPA-Personal, please enter a Pass Phrase in the corresponding
  • D-Link DAP-2610 | User Manual - Page 21
    D-Link DAP-2610 User Manual WPA Mode: When WPA-Enterprise is selected, you must also select a rates. Network Access Protection: Enable or disable Microsoft Network Access Protection. RADIUS Server: Enter the IP address of the RADIUS server. RADIUS Port: Enter the RADIUS port. RADIUS Secret: Enter the
  • D-Link DAP-2610 | User Manual - Page 22
    D-Link DAP-2610 User Manual LAN LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for the DAP-2610. These settings may be referred to as private settings. You may change the LAN IP address if needed. The LAN IP address is
  • D-Link DAP-2610 | User Manual - Page 23
    D-Link DAP-2610 User Manual IPv6 Enable IPv6: Check to enable the IPv6 Get IP From: Auto is chosen here. Choose this option the DAP-2610 can get IPv6 address automatically or use Static to set IPv6 address manually. When Auto is selected, the other fields here will be grayed out. IP Address: Enter
  • D-Link DAP-2610 | User Manual - Page 24
    D-Link DAP-2610 User Manual Advanced Settings In the Advanced Settings Section the user can configure advanced settings concerning Performance, Multiple SSID, VLAN, Security, Quality of Service, AP Array, Web Redirection, DHCP Server, Filters and Scheduling. The following pages will explain settings
  • D-Link DAP-2610 | User Manual - Page 25
    D-Link DAP-2610 User Manual Performance On the Performance Settings page the users can configure more advanced settings an access point to synchronize a wireless network. Specify a value in milliseconds. The default (100) is recommended. Setting a higher beacon interval can help to save the
  • D-Link DAP-2610 | User Manual - Page 26
    D-Link DAP-2610 User Manual Transmit Power: This setting determines the power level of messages passing through the AP. Multicast Rate: Adjust the multicast packet data rate here. The multicast rate is supported in AP mode, (2.4 GHZ and 5 GHZ) and WDS with AP mode, including Multi-SSIDs. Multicast
  • D-Link DAP-2610 | User Manual - Page 27
    D-Link DAP-2610 User Manual Wireless Resource Control The Wireless Resource Control window is used to configure the wireless connection settings so that the device can detect the better wireless connection in your environment. Wireless band: Select 2.4GHz or 5GHz. Band Steering:
  • D-Link DAP-2610 | User Manual - Page 28
    D-Link DAP-2610 User Manual 11n Preferred: Use the drop-down menu to Enable the 11n Preferred function. The wireless clients with 802.11n protocol will have higher priority to connect to the device. Network Utilization: Set the maximum utilization of this access point for service. The DAP-2610
  • D-Link DAP-2610 | User Manual - Page 29
    D-Link DAP-2610 User Manual Multi-SSID The device supports up to four multiple Service Set Identifiers. You can set the Primary SSID in the Basic > Wireless section. The SSID's factory default setting is dlink. The SSID can be easily changed to connect to an existing wireless network or to establish
  • D-Link DAP-2610 | User Manual - Page 30
    Link DAP-2610 User Manual Encryption: When you select Open System, toggle between Enable and Disable. If Enable is selected, the Key Type, Key Size, Key Index (1~4), Key, and Confirm Keys must also be configured . The default value of IP address of the RADIUS server. In addition, you must configure
  • D-Link DAP-2610 | User Manual - Page 31
    D-Link DAP-2610 User Manual VLAN VLAN List The DAP-2610 supports VLANs. VLANs can be created with a Name and VID. Mgmt (TCP stack), LAN, Primary/Multiple SSID, and WDS connection can be assigned to VLANs as they are physical ports. Any packet which enters the DAP-2610 without a VLAN tag will have a
  • D-Link DAP-2610 | User Manual - Page 32
    D-Link DAP-2610 User Manual Port List The Port List tab displays the current ports. If you want to configure the guest and internal networks on a Virtual LAN (VLAN), the switch and DHCP server you are using must also support VLANs. As a prerequisite step, configure a port on the switch for handling
  • D-Link DAP-2610 | User Manual - Page 33
    D-Link DAP-2610 User Manual Add/Edit VLAN The Add/Edit VLAN tab is used to configure VLANs. Once you have made the desired changes, click the Save button to let your changes take effect. VLAN Status: Use the radio button to
  • D-Link DAP-2610 | User Manual - Page 34
    D-Link DAP-2610 User Manual PVID Settings The PVID Setting tab is used to enable/disable the Port VLAN Identifier Auto Assign Status as well as to configure various types of PVID settings. Click the Save button to let your changes take effect. VLAN Status: Use the radio button to toggle between
  • D-Link DAP-2610 | User Manual - Page 35
    D-Link DAP-2610 User Manual Intrusion The Wireless Intrusion Protection window is used to set APs as All, Valid, Neighborhood, Rogue, and New. Click the Save button to let your
  • D-Link DAP-2610 | User Manual - Page 36
    D-Link DAP-2610 User Manual Schedule The Wireless Schedule Settings window is used to add and modify scheduling rules on the device. Click the Save button to let your changes
  • D-Link DAP-2610 | User Manual - Page 37
    D-Link DAP-2610 User Manual Internal RADIUS Server The DAP-2610 features a built-in RADIUS server. Once you have finished adding a RADIUS account, click the Save button to let your changes take effect. The newly-created
  • D-Link DAP-2610 | User Manual - Page 38
    D-Link DAP-2610 User Manual ARP Spoofing Prevention The ARP Spoofing Prevention feature allows users to add IP/MAC address mapping to prevent arp spoofing attack. ARP Spoofing Prevention: This check box allows you to enable the arp spoofing prevention function. Gateway IP Address: Enter a gateway IP
  • D-Link DAP-2610 | User Manual - Page 39
    D-Link DAP-2610 User Manual Bandwidth Optimization The Bandwidth Optimization window allows the user to manage the bandwidth of the device and arrange the bandwidth for various wireless clients. When
  • D-Link DAP-2610 | User Manual - Page 40
    D-Link DAP-2610 User Manual Band: Use the drop-down menu to toggle the wireless band between 2.4GHz and 5GHz. SSID Index: Use the drop-down menu to select the
  • D-Link DAP-2610 | User Manual - Page 41
    D-Link DAP-2610 User Manual AP Array AP Array Scan The AP Array window is used to create up to 32 APs on a local network to be Master IP, MAC, Master, Backup Master, Slave, and Total. Current Members: This table displays all the current array members. The DAP-2610 AP array feature supports up
  • D-Link DAP-2610 | User Manual - Page 42
    D-Link DAP-2610 User Manual Configuration Settings In the AP array configuration settings windows, users can the changes made. Enable AP Array Select to Enable or Disable the AP array configure Configuration: feature here. Wireless Basic Select this option to specify the basic wireless Settings
  • D-Link DAP-2610 | User Manual - Page 43
    D-Link DAP-2610 User Manual Wireless Basic Settings Network Name (SSID): Select this option to use the same SSID. SSID Visibility: Select this option to enable SSID visibility. Auto Channel
  • D-Link DAP-2610 | User Manual - Page 44
    D-Link DAP-2610 User Manual Short GI: Select this option to use the same short GI settings. Link Integrity: Select this option to use the same link settings. QoS Settings: Select this option to use the same Quality of Service settings. Log Settings: Select this option to use the same log settings.
  • D-Link DAP-2610 | User Manual - Page 45
    D-Link DAP-2610 User Manual ARP Spoofing Select this option to use the same ARP spoofing prevention settings. Prevention: Bandwidth Select this option to use the same bandwidth optimization settings.
  • D-Link DAP-2610 | User Manual - Page 46
    D-Link DAP-2610 User Manual Auto-RF In this windows, users can view and configure the automatic radio frequency settings as well as configure the the auto-initiate period and threshold values. Click the Save button to accept the changes made. Enable: Auto-RF: Select to Enable or Disable
  • D-Link DAP-2610 | User Manual - Page 47
    D-Link DAP-2610 User Manual Load Balance In this window, users can view and configure the AP array's load balancing settings. Click the Save button to accept the changes made. Enable Load Balance: Select to Enable or Disable the load
  • D-Link DAP-2610 | User Manual - Page 48
    Link DAP-2610 User Manual Captive Portal Authentication Settings-Web Redirection Only The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication page. In this window, user can view and configure Default
  • D-Link DAP-2610 | User Manual - Page 49
    D-Link DAP-2610 User Manual IP Address : Assign a static IP address that is within the IP address range of your network. Subnet Mask : Enter the subnet mask. All devices in the network must share the same subnet mask. Gateway : Enter the IP address of the gateway/router in your network. DNS : Enter
  • D-Link DAP-2610 | User Manual - Page 50
    Link DAP-2610 User Manual Authentication Settings- Username/Password The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication page. In this window, user can view and configure State : Default is Disable
  • D-Link DAP-2610 | User Manual - Page 51
    D-Link DAP-2610 User Manual IP (DHCP) is selected, the other fields here will be grayed out. Please allow about 2 minutes for the DHCP client to be functional once this selection is made. IP Address : Assign a static IP address that is within the IP address range of your network. Subnet Mask : Enter
  • D-Link DAP-2610 | User Manual - Page 52
    Link DAP-2610 User Manual Authentication Settings- Passcode The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication page. In this window, user can view and configure State : Default is Disable
  • D-Link DAP-2610 | User Manual - Page 53
    D-Link DAP-2610 User Manual grayed out. Please allow about 2 minutes for the DHCP client to be functional once this selection is made. IP Address : Assign a static IP address that is within the IP address range of your network. Subnet Mask : Enter the subnet mask. All devices in the network must
  • D-Link DAP-2610 | User Manual - Page 54
    Link DAP-2610 User Manual Authentication Settings- Remote RADIUS The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication page. In this window, user can view and configure State : Default is Disable or
  • D-Link DAP-2610 | User Manual - Page 55
    D-Link DAP-2610 User Manual IP Address : Assign a static IP address that is within the IP address range of your network. Subnet Mask : Enter the subnet mask. All devices in the network must share the same subnet mask. Gateway : Enter the IP address of the gateway/router in your network. DNS : Enter
  • D-Link DAP-2610 | User Manual - Page 56
    Link DAP-2610 User Manual Authentication Settings- LDAP The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication page. In this window, user can view and configure Redirection State : Default is Disable or
  • D-Link DAP-2610 | User Manual - Page 57
    D-Link DAP-2610 User Manual Subnet Mask : Enter the subnet mask. All devices in the network must share the same subnet mask. Gateway : Enter the IP address of the gateway/router in your network. DNS : Enter a DNS server IP address. This is usually the local IP address of your gateway/router. Server:
  • D-Link DAP-2610 | User Manual - Page 58
    Link DAP-2610 User Manual Authentication Settings- POP3 The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication page. In this window, user can view and configure Redirection State : Default is Disable or
  • D-Link DAP-2610 | User Manual - Page 59
    D-Link DAP-2610 User Manual (DHCP) is selected, the other fields here will be grayed out. Please allow about 2 minutes for the DHCP client to be functional once this selection is made. IP Address : Assign a static IP address that is within the IP address range of your network. Subnet Mask : Enter
  • D-Link DAP-2610 | User Manual - Page 60
    D-Link DAP-2610 User Manual Login Page Upload In this window, users can upload a field the path to the login style file, that will From Local Hard Drive: be uploaded, will be displayed. Alternatively, the path can be manually entered here. Login Page Style List : Select the wireless band and
  • D-Link DAP-2610 | User Manual - Page 61
    D-Link DAP-2610 User Manual IP Filter Settings Enter the IP address or network address that will be used in the IP filter rule. For example, an IP address like 192.168.70.66 or a network address like 192.168.70.0. This IP address or network will be inaccessible to wireless clients in this network.
  • D-Link DAP-2610 | User Manual - Page 62
    D-Link DAP-2610 User Manual MAC Bypass The DAP-2610 features a wireless MAC Bypass. Once a user is finished with these settings, click on the computer, and then click Upload. Load MAC File to Local To download MAC bypass list file, click Download Hard Driver: and to save the MAC bypass list. 62
  • D-Link DAP-2610 | User Manual - Page 63
    Host Configuration Protocol (DHCP) assigns dynamic IP addresses to devices on the network. This protocol simplifies network management and allows new wireless devices to receive IP addresses automatically without the need to manually assign new IP addresses. Select Enable to allow the DAP-2610 to
  • D-Link DAP-2610 | User Manual - Page 64
    D-Link DAP-2610 User Manual Static Pool Setting The DHCP address pool defines the range of IP addresses that can be assigned to stations on the network. A static pool allows specific wireless stations to receive a fixed IP without time control. Function Enable/Disable: Dynamic Host Configuration
  • D-Link DAP-2610 | User Manual - Page 65
    D-Link DAP-2610 User Manual Current IP Mapping List This window displays information about the current assigned DHCP dynamic and static IP address pools. This information is available when you enable DHCP server on the AP and assign dynamic and static IP address pools. Current DHCP Dynamic These are
  • D-Link DAP-2610 | User Manual - Page 66
    D-Link DAP-2610 User Manual Filters Wireless MAC ACL This page allows the user to configure Wireless MAC ACL settings for access control. Wireless Band: Displays the current wireless band rate. Access Control List: Select Disable to disable the filters function.
  • D-Link DAP-2610 | User Manual - Page 67
    D-Link DAP-2610 User Manual This page allows the user to configure a WLAN Partition. WLAN Partition Wireless Band: Displays the current wireless band. Link Integrity: Select Enable or Disable. If the Ethernet connection between the LAN and the AP is disconnected, enabling this feature will cause
  • D-Link DAP-2610 | User Manual - Page 68
    D-Link DAP-2610 User Manual Traffic Control Uplink/Downlink Setting The uplink/downlink setting allows users to customize the downlink and uplink interfaces including specifying downlink/uplink bandwidth rates in
  • D-Link DAP-2610 | User Manual - Page 69
    D-Link DAP-2610 User Manual QoS Quality of Service (QoS) enhances the experience of using a network by prioritizing the traffic of different applications. The DAP-2610 supports four priority levels. Once the desired QoS settings are finished, click the Save button to let your changes take effect.
  • D-Link DAP-2610 | User Manual - Page 70
    D-Link DAP-2610 User Manual Traffic Manager The traffic manager feature allows users to create traffic management rules that specify how to deal with listed client traffic and specify downlink/
  • D-Link DAP-2610 | User Manual - Page 71
    D-Link DAP-2610 User Manual Status In the Status Section the user can monitor and view configuration settings of the access point. Here the user can also view statistics about client information, WDS information and more. The following pages will explain settings
  • D-Link DAP-2610 | User Manual - Page 72
    D-Link DAP-2610 User Manual Device Information This page displays the current information like firmware version, Ethernet and wireless parameters, as well as the information regarding CPU and memory utilization. Device Information: This read-only window displays the configuration settings of the
  • D-Link DAP-2610 | User Manual - Page 73
    D-Link DAP-2610 User Manual Client Information This page displays the associated clients SSID, MAC, band, authentication method, signal strength, and power saving mode for the DAP-2610 network. Client Information: This window displays the wireless client information for clients currently connected
  • D-Link DAP-2610 | User Manual - Page 74
    D-Link DAP-2610 User Manual WDS Information Page This page displays the access points SSID, MAC, band, authentication method, signal strength, and status for the DAP-2610's Wireless Distribution System network. WDS Information: ThiswindowdisplaystheWirelessDistribution System information for clients
  • D-Link DAP-2610 | User Manual - Page 75
    D-Link DAP-2610 User Manual Channel Analyze Wireless Band: Select either 2.4Ghz or 5GHz. Detect: Click the Detect button to scan. AP List: This will list the transmitting channels and quality. 75
  • D-Link DAP-2610 | User Manual - Page 76
    D-Link DAP-2610 User Manual Stats Page Ethernet Traffic Statistics Displays wired interface network traffic information. Ethernet Traffic Statistics: This page displays transmitted and received count statistics for packets and bytes. 76
  • D-Link DAP-2610 | User Manual - Page 77
    D-Link DAP-2610 User Manual WLAN Traffic Statistics Displays throughput, transmitted frame, received frame, and WEP frame error information for the AP network. WLAN Traffic Statistics: This page displays wireless
  • D-Link DAP-2610 | User Manual - Page 78
    D-Link DAP-2610 User Manual Log View Log The AP's embedded memory holds logs here. The log information includes but is not limited to the following items: cold start AP, upgrading firmware, client associate and disassociate with AP, and web login. The web page holds up to 500 logs. View Log: The
  • D-Link DAP-2610 | User Manual - Page 79
    D-Link DAP-2610 User Manual Log Settings Enter the log server's IP address to send the log to that server. Check or uncheck System Activity, Wireless Activity, or Notice to specify what kind of log type you want it to log. Log Server/IP Address: Enter the IP address of the server you would like to
  • D-Link DAP-2610 | User Manual - Page 80
    D-Link DAP-2610 User Manual Maintenance Section In the Status Section the user can monitor and view configuration settings of the access point. Here the user can also view statistics about client information, WDS information and more. The following pages will explain settings
  • D-Link DAP-2610 | User Manual - Page 81
    D-Link DAP-2610 User Manual Administration Limit Administrator Check one or more of the administrator will be allowed to log in from. Limit Administrator IP: Check to enable the Limit Administrator IP address. IP Range: Enter the IP address range that the administrator will be allowed to log in from
  • D-Link DAP-2610 | User Manual - Page 82
    D-Link DAP-2610 User Manual System Name Settings Each of the five main categories display various hidden administrator parameters and settings. System Name: The name of the device. The default name is D-Link DAP-2610. Location: The physical location of the device, e.g. 72nd Floor, D-Link HQ. Login
  • D-Link DAP-2610 | User Manual - Page 83
    D-Link DAP-2610 User Manual SNMP Settings Each of the five main categories display various hidden administrator parameters and settings. Status: Check the box to enable the SNMP functions. This is enabled by default. Public Community String: Enter the public SNMP community string. Private Community
  • D-Link DAP-2610 | User Manual - Page 84
    D-Link DAP-2610 User Manual Administration Central WiFiManager Settings The Central WiFiManager section is used to create a set of APs on the Internet to be organized into a single group in
  • D-Link DAP-2610 | User Manual - Page 85
    D-Link DAP-2610 User Manual Firmware and SSL Upload This page allows the user to perform a firmware upgrade. A Firmware upgrade is a function that upgrade the running software used by the access point. This is a useful feature that prevents future bugs and allows for new
  • D-Link DAP-2610 | User Manual - Page 86
    Open" and "Upload" to update the configuration. Download Configuration File: Click "Download" to save the current configuration file to your local disk. Note that if you save one configuration file with the administrator's password now, after resetting your DAP-2610 and then updating to this saved
  • D-Link DAP-2610 | User Manual - Page 87
    D-Link DAP-2610 User Manual Time and Date Settings Enter the NTP server IP, choose the time zone, and enable or menu to select the Dates: correct Daylight Saving offset. Set the Date and Time Manually: A user can either manually set the time for the AP here, or click the Copy Your Computer's Time
  • D-Link DAP-2610 | User Manual - Page 88
    D-Link DAP-2610 User Manual Configuration and System These options are the remaining option to choose from in the top menu. Configuration allows the user to save and activate or discard the configurations done. System allows the user to restart the unit, perform a factory reset or clear the language
  • D-Link DAP-2610 | User Manual - Page 89
    D-Link DAP-2610 User Manual System Settings On this page the user can restart the unit, perform a factory reset of the access point or clear the added language pack. Restart the Device: Click Restart to restart the DAP-2610. Restore to Factory Default Click Restore to restore the DAP-2610 Settings:
  • D-Link DAP-2610 | User Manual - Page 90
    D-Link DAP-2610 User Manual Help The help page is useful to view a brief description of a function available on the access point in case the manual is not present. Help: Scroll down the Help page for topics and explanations. 90
  • D-Link DAP-2610 | User Manual - Page 91
    Inexpensive solution - wireless network devices are as competitively priced as conventional Ethernet network devices. The DAP-2610 saves money by providing users with multi-functionality configurable in four different modes. • Scalability - Configurations can be easily changed and range from Peer-to
  • D-Link DAP-2610 | User Manual - Page 92
    D-Link DAP-2610 User Manual Wireless Installation Considerations The D-Link Access Point lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however,
  • D-Link DAP-2610 | User Manual - Page 93
    D-Link DAP-2610 User Manual Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DAP-2610. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different
  • D-Link DAP-2610 | User Manual - Page 94
    D-Link DAP-2610 User Manual How to check your IP address? After you install your network adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start >
  • D-Link DAP-2610 | User Manual - Page 95
    D-Link DAP-2610 User Manual How to statically assign an IP address? If you are not using a DHCP capable gateway/router, or you need to assign a static IP network. Set Default Gateway the same as the LAN IP address of your router (192.168.0.1). Set Primary DNS the same as the LAN IP address of your
  • D-Link DAP-2610 | User Manual - Page 96
    D-Link DAP-2610 User Manual Standards • IEEE 802. (HTTP, Secure HTTP (HTTPS)) • Central WiFiManager • SNMP Support (Private MIB) • Command Line Interface (Telnet, Secure SSH W = 170 mm • H = 28 mm Operating Voltage • 802.3af PoE or 12V/1A Antenna Type • 2 internal dual-band 3 dBi omni antennas 96
  • D-Link DAP-2610 | User Manual - Page 97
    D-Link DAP-2610 User Manual Antenna Pattern Orientation 2.4 GHz Ceiling Mounted Antenna Pattern H-Plane E-Plane 2.4 GHz Wall Mounted 5 GHz Ceiling Mounted 5 GHz Wall Mounted 97
  • D-Link DAP-2610 | User Manual - Page 98
    D-Link DAP-2610 User Manual Warranty Subject to the terms and conditions set forth herein, D-Link Systems, Inc. ("D-Link") provides this Limited Warranty: • Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and • Only for
  • D-Link DAP-2610 | User Manual - Page 99
    Link DAP-2610 User Manual Limited Software Warranty: D-Link warrants that the software portion of the product ("Software") will substantially conform to D-Link Link's functional specifications for the Software or to refund the portion of the actual purchase price from D-Link Technical Support (USA
  • D-Link DAP-2610 | User Manual - Page 100
    D-Link DAP-2610 User Manual • After an RMA number is issued, the defective product must be software, firmware or other products or services provided by anyone other than D-Link; and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the
  • D-Link DAP-2610 | User Manual - Page 101
    Link DAP-2610 User Manual While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link Service PRODUCT. THE MAXIMUM LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE
  • D-Link DAP-2610 | User Manual - Page 102
    Link DAP-2610 User Manual derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link and used in accordance with the instructions, may cause harmful interference to of this product in the U.S.A. is firmware-limited to channels 1 through 11.
  • D-Link DAP-2610 | User Manual - Page 103
    D-Link DAP-2610 User Manual For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link office. This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter
  • D-Link DAP-2610 | User Manual - Page 104
    D-Link DAP-2610 User Manual Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.01 March 29, 2017 104
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Document Created by Nick Schuster