Home » D-Link Manuals » Hubs & Switches » D-Link DES-3828 » Manual Viewer

D-Link DES-3828 Product Manual - Page 110

create vlan, show vlan, Advertisement : Enabled

UPC - 790069276811

Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual Command show pvid auto_assign Parameters Each command is listed, in detail, in the following sections. create vlan Purpose Syntax Description Parameters Restrictions Used to create a VLAN on the Switch. create vlan {tag | advertisement} This command allows the creation of a VLAN on the Switch. − The name of the VLAN to be created. − The VLAN ID of the VLAN to be created. Allowed values = 1-4094 advertisement − Specifies that the VLAN is able to join GVRP. If this parameter is not set, the VLAN cannot be configured to have forbidden ports. Only Administrator or Operator-level users can issue this command.Each VLAN name can be up to 32 characters. If the VLAN is not given a tag, it will be a port-based VLAN. Up to 4k static VLANs may be created per configuration. Example usage: To create a VLAN v1, tag 2: DES-3800:admin#create vlan v1 tag 2 Command: create vlan v1 tag 2 Success. DES-3800:admin# show vlan Purpose Syntax Description Parameters Restrictions Used to display the current VLAN configuration on the Switch show vlan {} This command displays summary information about each VLAN including the VLAN ID, VLAN name, the Tagging/Untagging status, and the Member/Non-member/Forbidden status of each port that is a member of the VLAN. − The VLAN name of the VLAN for which to display a summary of settings. None. Example usage: To display the Switch's current VLAN settings: DES-3800:admin#show vlan Command: show vlan VID VLAN TYPE : 1 : static VLAN Name : default Advertisement : Enabled 106

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443