Home » D-Link Manuals » Hubs & Switches » D-Link DES-3828 » Manual Viewer

D-Link DES-3828 Product Manual - Page 12

Line Editing Key Usage, Multiple Display Control Keys, braces} - review

UPC - 790069276811

Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual {braces} Purpose Syntax Description Example command Encloses an optional value or set of optional arguments. reset {[config | system]} In the above syntax example, you have the option to specify config or detail. It is not necessary to specify either optional value, however the effect of the system reset is dependent on which, if any, value is specified. Therefore, with this example there are three possible outcomes of performing a system reset. See the following chapter, Basic Commands for more details about the reset command. reset config Line Editing Key Usage Delete Deletes the character under the cursor and then shifts the remaining characters in the line to the left. Backspace Deletes the character to the left of the cursor and then shifts the remaining characters in the line to the left. Insert or Ctrl+R Toggle on and off. When toggled on, inserts text and shifts previous text to the right. Left Arrow Moves the cursor to the left. Right Arrow Moves the cursor to the right. Up Arrow Repeats the previously entered command. Each time the up arrow is pressed, the command previous to that displayed appears. This way it is possible to review the command history for the current session. Use the down arrow to progress sequentially forward through the command history list. Down Arrow The down arrow will display the next command in the command history entered in the current session. This displays each command sequentially as it was entered. Use the up arrow to review previous commands. Tab Shifts the cursor to the next field to the left. Multiple Page Display Control Keys Space Displays the next page. CTRL+c Stops the display of remaining pages when multiple pages are to be displayed. ESC Stops the display of remaining pages when multiple pages are to be displayed. n Displays the next page. p Displays the previous page. q Stops the display of remaining pages when multiple pages are to be displayed. r Refreshes the pages currently displayed. a Displays the remaining pages without pausing between pages. Enter Displays the next line or table entry. 8

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

Match case Limit results 1 per page

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

{braces}

Purpose

Encloses an optional value or set of optional arguments.

Syntax

reset {[config | system]}

Description

In the above syntax example, you have the option to specify

config

detail

. It

is not necessary to specify either optional value, however the effect of the

system reset is dependent on which, if any, value is specified. Therefore, with

this example there are three possible outcomes of performing a system reset.

See the following chapter, Basic Commands for more details about the reset

command.

Example

command

reset config

Line Editing Key Usage

Delete

Deletes the character under the cursor and then shifts the remaining characters

in the line to the left.

Backspace

Deletes the character to the left of the cursor and then shifts the remaining

characters in the line to the left.

Insert or Ctrl+R

Toggle on and off. When toggled on, inserts text and shifts previous text to the

right.

Left Arrow

Moves the cursor to the left.

Right Arrow

Moves the cursor to the right.

Up Arrow

Repeats the previously entered command. Each time the up arrow is pressed,

the command previous to that displayed appears. This way it is possible to

review the command history for the current session. Use the down arrow to

progress sequentially forward through the command history list.

Down Arrow

The down arrow will display the next command in the command history entered

in the current session. This displays each command sequentially as it was

entered. Use the up arrow to review previous commands.

Tab

Shifts the cursor to the next field to the left.

Multiple Page Display Control Keys

Space

Displays the next page.

CTRL+c

Stops the display of remaining pages when multiple pages are to be displayed.

ESC

Stops the display of remaining pages when multiple pages are to be displayed.

Displays the next page.

Displays the previous page.

Stops the display of remaining pages when multiple pages are to be displayed.

Refreshes the pages currently displayed.

Displays the remaining pages without pausing between pages.

Enter

Displays the next line or table entry.