Home » D-Link Manuals » Hubs & Switches » D-Link DES-3828 » Manual Viewer

D-Link DES-3828 Product Manual - Page 138

show 802.1x auth_state, Authentication Protocol : Radius_Eap

UPC - 790069276811

Add to My Manuals
Save this manual to your list of manuals

Page 138 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual Example usage: To display the 802.1x authentication states: DES-3800:admin#show 802.1x auth_configuration ports 1 Command: show 802.1x auth_configuration ports 1 802.1X : Enabled Authentication Mode : Port_based Authentication Protocol : Radius_Eap Port number : 1 Capability : None AdminCrlDir : Both OpenCrlDir : Both Port Control : Auto QuietPeriod : 60 sec TxPeriod : 30 sec SuppTimeout : 30 sec ServerTimeout : 30 sec MaxReq : 2 times ReAuthPeriod : 3600 sec ReAuthenticate : Disabled CTRL+C ESC q Quit SPACE n Next Page Enter Next Entry a All show 802.1x auth_state Purpose Used to display the current authentication state of the 802.1x server on the Switch. Syntax show 802.1x auth_state {ports } Description The show 802.1x auth_state command is used to display the current authentication state of the 802.1x Port-based or MAC-based Network Access Control server application on the Switch. Parameters ports − Specifies a port or range of ports to be viewed. The following details what is displayed: Port number − Shows the physical port number on the Switch. Auth PAE State: Initialize / Disconnected / Connecting / Authenticating / Authenticated / Held / ForceAuth / ForceUnauth − Shows the current state of the Authenticator PAE. Backend State: Request / Response / Fail / Idle / Initialize / Success / Timeout − Shows the current state of the Backend Authenticator. Port Status: Authorized / Unauthorized − Shows the result of the authentication process. Authorized means that the user was authenticated, and can access the network. Unauthorized means that the user was not authenticated, and cannot access the network. Restrictions None. Example usage: To display the 802.1x auth state for Port-based 802.1x: DES-3800:admin#show 802.1x auth_state Command: show 802.1x auth_state Port ---1 2 3 Auth PAE State ForceAuth ForceAuth ForceAuth Backend State Success Success Success 134 Port Status ----------- Authorized Authorized Authorized

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

Match case Limit results 1 per page

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

134

Example usage:

To display the 802.1x authentication states:

DES-3800:admin#show 802.1x auth_configuration ports 1

Command: show 802.1x auth_configuration ports 1

802.1X

: Enabled

Authentication Mode

: Port_based

Authentication Protocol : Radius_Eap

Port number

: 1

Capability

: None

AdminCrlDir

: Both

OpenCrlDir

: Both

Port Control

: Auto

QuietPeriod

: 60

sec

TxPeriod

: 30

sec

SuppTimeout

: 30

sec

ServerTimeout

: 30

sec

MaxReq

: 2

times

ReAuthPeriod

: 3600

sec

ReAuthenticate : Disabled

CTRL+C ESC q

Quit

SPACE n

Enter

All

show 802.1x auth_state

Purpose

Used to display the current authentication state of the 802.1x server on the

Switch.

Syntax

show 802.1x auth_state {ports <portlist>}

Description

The

show 802.1x auth_state

command is used to display the current

authentication state of the 802.1x Port-based or MAC-based Network

Access Control server application on the Switch.

Parameters

ports <portlist>

−

Specifies a port or range of ports to be viewed.

The following details what is displayed:

Port number

−

Shows the physical port number on the Switch.

Auth PAE State: Initialize / Disconnected / Connecting / Authenticating /

Authenticated / Held / ForceAuth / ForceUnauth

−

Shows the current state

of the Authenticator PAE.

Backend State: Request / Response / Fail / Idle / Initialize / Success /

Timeout

−

Shows the current state of the Backend Authenticator.

Port Status: Authorized / Unauthorized

−

Shows the result of the

authentication process. Authorized means that the user was

authenticated, and can access the network. Unauthorized means that the

user was not authenticated, and cannot access the network.

Restrictions

None.

Example usage:

To display the 802.1x auth state for Port-based 802.1x:

DES-3800:admin#show 802.1x auth_state

Command: show 802.1x auth_state

Port

Auth

PAE State

Backend State

Port Status

----

----------------

-------------

-----------

ForceAuth

Success

Authorized

ForceAuth

Success

Authorized

ForceAuth

Success

Authorized