D-Link DES-3828 Product Manual - Page 191

RIP Commands, <password 16> | disable] | tx_mode [disable | v1_only

Get D-Link DES-3828 - xStack Switch - Stackable PDF manuals and user guides
UPC - 790069276811
View all D-Link DES-3828 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 191 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual 26 RIP COMMANDS The RIP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command config rip enable rip disable rip config rip timer show rip Parameters [ipif | all] {authentication [enable | disable] | tx_mode [disable | v1_only | v1_compatible | v2_only] | rx_mode [v1_only | v2_only | v1_or_v2 | disable] state [enable | disable]} [update_interval | timeout_interval | garbage_collect_interval ] ipif Each command is listed, in detail, in the following sections. config rip Purpose Syntax Description Parameters Used to configure RIP on the Switch. config rip [ipif | all] {authentication [enable | disable] | tx_mode [disable | v1_only | v1_compatible | v2_only] | rx_mode [v1_only | v2_only | v1_or_v2 | disable] state [enable | disable]} This command is used to configure RIP on the Switch. − The name of the IP interface. all - To configure all RIP receiving mode for all IP interfaces. authentication [enable | disable] − Enables or disables authentication for RIP on the Switch. • − Allows the specification of a case-sensitive password. tx_mode − Determines how received RIP packets will be interpreted - as RIP version V1 only, V2 Only, or V1 Compatible (V1 and V2). This entry specifies which version of the RIP protocol will be used to transfer RIP packets. The disabled entry prevents the reception of RIP packets. • disable − Prevents the transmission of RIP packets. • v1_only − Specifies that only RIP v1 packets will be transmitted. • v1_compatible - Specifies that only RIP v1 compatible packets will be transmitted. • v2_only - Specifies that only RIP v2 packets will be transmitted. rx_mode − Determines how received RIP packets will be interpreted - as RIP version V1 only, V2 Only, or V1 or V2. This entry specifies which version of the RIP protocol will be used to receive RIP packets. The Disabled entry prevents the reception of RIP packets. • v1_only − Specifies that only RIP v1 packets will be transmitted. • v2_only - Specifies that only RIP v2 packets will be transmitted. • v1_or_v2 - Specifies that only RIP v1 or v2 packets will be transmitted. 187

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316
  • 317
  • 318
  • 319
  • 320
  • 321
  • 322
  • 323
  • 324
  • 325
  • 326
  • 327
  • 328
  • 329
  • 330
  • 331
  • 332
  • 333
  • 334
  • 335
  • 336
  • 337
  • 338
  • 339
  • 340
  • 341
  • 342
  • 343
  • 344
  • 345
  • 346
  • 347
  • 348
  • 349
  • 350
  • 351
  • 352
  • 353
  • 354
  • 355
  • 356
  • 357
  • 358
  • 359
  • 360
  • 361
  • 362
  • 363
  • 364
  • 365
  • 366
  • 367
  • 368
  • 369
  • 370
  • 371
  • 372
  • 373
  • 374
  • 375
  • 376
  • 377
  • 378
  • 379
  • 380
  • 381
  • 382
  • 383
  • 384
  • 385
  • 386
  • 387
  • 388
  • 389
  • 390
  • 391
  • 392
  • 393
  • 394
  • 395
  • 396
  • 397
  • 398
  • 399
  • 400
  • 401
  • 402
  • 403
  • 404
  • 405
  • 406
  • 407
  • 408
  • 409
  • 410
  • 411
  • 412
  • 413
  • 414
  • 415
  • 416
  • 417
  • 418
  • 419
  • 420
  • 421
  • 422
  • 423
  • 424
  • 425
  • 426
  • 427
  • 428
  • 429
  • 430
  • 431
  • 432
  • 433
  • 434
  • 435
  • 436
  • 437
  • 438
  • 439
  • 440
  • 441
  • 442
  • 443
  • 444
  • 445
  • 446
  • 447
  • 448
  • 449
  • 450
  • 451
  • 452
xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual
187
26
RIP
C
OMMANDS
The RIP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table.
Command
Parameters
config rip
[ipif <ipif_name 12> | all] {authentication [enable <password
16> | disable] | tx_mode [disable | v1_only | v1_compatible |
v2_only] | rx_mode [v1_only | v2_only | v1_or_v2 | disable]
state [enable | disable]}
enable rip
disable rip
config rip timer
[update_interval <sec 1-65535> | timeout_interval <sec 1-
65535> | garbage_collect_interval
<sec 1-65535>]
show rip
ipif <ipif_name 12>
Each command is listed, in detail, in the following sections.
config rip
Purpose
Used to configure RIP on the Switch.
Syntax
config rip [ipif <ipif_name 12> | all] {authentication [enable
<password 16> | disable] | tx_mode [disable | v1_only |
v1_compatible | v2_only] | rx_mode [v1_only | v2_only | v1_or_v2 |
disable] state [enable | disable]}
Description
This command is used to configure RIP on the Switch.
Parameters
<ipif_name 12>
−
The name of the IP interface.
all
– To configure all RIP receiving mode for all IP interfaces.
authentication [enable | disable]
−
Enables or disables authentication for
RIP on the Switch.
•
<password 16>
−
Allows the specification of a case-sensitive
password.
tx_mode
−
Determines how received RIP packets will be interpreted – as
RIP version
V1 only
,
V2 Only
,
or
V1 Compatible (V1 and V2)
.
This entry
specifies which version of the RIP protocol will be used to transfer RIP
packets. The disabled entry prevents the reception of RIP packets.
•
disable
−
Prevents the transmission of RIP packets.
•
v1_only
−
Specifies that only RIP v1 packets will be transmitted.
•
v1_compatible –
Specifies that only RIP v1 compatible packets
will be transmitted.
•
v2_only
- Specifies that only RIP v2 packets will be transmitted.
rx_mode
−
Determines how received RIP packets will be interpreted – as
RIP version
V1 only, V2 Only
,
or
V1 or V2
.
This entry specifies which
version of the RIP protocol will be used to receive RIP packets. The
Disabled entry prevents the reception of RIP packets.
•
v1_only
−
Specifies that only RIP v1 packets will be transmitted.
•
v2_only
- Specifies that only RIP v2 packets will be transmitted.
•
v1_or_v2
- Specifies that only RIP v1 or v2 packets will be
transmitted.