Home » D-Link Manuals » Hubs & Switches » D-Link DES-3828 » Manual Viewer

D-Link DES-3828 Product Manual - Page 196

config igmp, config igmp [ipif <ipif_name 12> | all] {version <value 1-3&gt

UPC - 790069276811

Add to My Manuals
Save this manual to your list of manuals

Page 196 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual config igmp Purpose Syntax Description Parameters Restrictions Used to configure IGMP on the Switch. config igmp [ipif | all] {version | query_interval | max_response_time | robustness_variable | last_member_query_interval | state [enable | disable]} This command allows users to configure IGMP on the Switch. − The name of the IP interface for which you want to configure IGMP. all − Specifies all the IP interfaces on the Switch. version − Select the IGMP version number. query_interval − The time in seconds between general query transmissions, in seconds. max_response_time − Enter the maximum time in seconds that the Switch will wait for reports from members. robustness_variable − This value states the permitted packet loss that guarantees IGMP. last_member_query_interval − The Max Response Time inserted into Group-Specific Queries and Group-and-Source specific queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query and Group-and-Source specific query messages. The default is 1 second state [enable | disable] − Enables or disables IGMP for the specified IP interface. Only Administrator or Operator-level users can issue this command. Example Usage: To configure the IGMPv2 for all IP interfaces. DES-3800:admin#config igmp all version 2 Command: config igmp all version 2 Success. DES-3800:admin# 192

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443