D-Link DES-3828 Product Manual - Page 205

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

201

30

DVMRP

C

OMMANDS

The DVMRP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following

table.

Command

Parameters

config dvmrp

[ipif <ipif_name 12> | all] {metric <value 1-31> | probe <sec

1-65535> | neighbor_timeout <sec 1-65535> | state [enable

| disable]}

enable dvmrp

disable dvmrp

show dvmrp neighbor

{ipif <ipif_name 12> | ipaddress <network_address>}

show dvmrp nexthop

{ipaddress <network_address> | ipif <ipif_name 12>}

show dvmrp routing_table

{ipaddress <network_address>}

show dvmrp

{ipif <ipif_name 12>}

Each command is listed, in detail, in the following sections.

config dvmrp

Purpose

Used to configure DVMRP on the Switch.

Syntax

config dvmrp [ipif <ipif_name 12> | all] {metric <value 1-31> | probe

<sec 1-65535> | neighbor_timeout <sec 1-65535> | state [enable |

disable]}

Description

This command is used to configure DVMRP on the Switch.

Parameters

ipif <ipif_name 12>

−

The name of the IP interface for which DVMRP is

to be configured.

all

−

Specifies that DVMRP is to be configured for all IP interfaces on

the Switch.

metric <value 1-31>

−

Allows the assignment of a DVMRP route cost to

the above IP interface. A DVMRP route cost is a relative number that

represents the real cost of using this route in the construction of a

multicast delivery tree. It is similar to, but not defined as, the hop count

in RIP. The default is 1.

probe <second 1-65535>

−

DVMRP defined an extension to IGMP that

allows routers to query other routers to determine if a DVMRP neighbor

is present on a given subnetwork or not. This is referred to as a ‘probe’.

This entry will set an intermittent probe (in seconds) on the device that

will transmit dvmrp messages, depending on the time specified. This

probe is also used to “keep alive” the connection between DVMRP

enabled devices. The default value is 10 seconds.

neighbor_timeout <second 1-65535>

−

The time period for which

DVMRP will hold Neighbor Router reports before issuing poison route

messages. The default value is 35 seconds.

state [enable | disable]

−

Allows DVMRP to be enabled or disabled.

Restrictions

Only Administrator or Operator-level users can issue this command.

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

D-Link DES-3828 Product Manual - Page 205

DVMRP Commands, <sec 1-65535> | neighbor_timeout <sec 1-65535> | state [enable

Page 205 highlights