Home » D-Link Manuals » Hubs & Switches » D-Link DES-3828 » Manual Viewer

D-Link DES-3828 Product Manual - Page 227

show ospf ipif, show ospf all

UPC - 790069276811

Add to My Manuals
Save this manual to your list of manuals

Page 227 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual show ospf ipif Syntax Description Parameters Restrictions show ospf ipif {} This command will display the current OSPF interface settings for the specified interface name. − The IP interface name for which to display the current OSPF interface settings. None. Usage Example: To display the current OSPF interface settings, for a specific OSPF interface: DES-3800:admin#show ospf ipif ipif2 Command: show ospf ipif ipif2 Interface Name: ipif2 ((Link Up) Network Medium Type: BROADCAST Area ID: 1.0.0.0 Priority: 1 DR Address: 123.234.12.34 Hello Interval: 10 Transmit Delay: 1 Authentication: None Total Entries: 1 IP Address: 123.234.12.34/24 Metric: 1 Administrative State: Enabled DR State: DR Backup DR Address: None Dead Interval: 40 Retransmit Time: 5 DES-3800:admin# show ospf all Purpose Syntax Description Parameters Restrictions Used to display the current OSPF settings of all the OSPF interfaces on the Switch. show ospf all This command will display the current OSPF settings for all OSPF interfaces on the Switch. None. Only Administrator or Operator-level users can issue this command. Usage example: To display the current OSPF interface settings, for all OSPF interfaces on the Switch: DES-3800:admin#show ospf all Command: show ospf all Interface Name: System Network Medium Type: BROADCAST Area ID: 0.0.0.0 Priority: 1 DR Address: 10.42.73.10 Hello Interval: 10 Transmit Delay: 1 Authentication: None IP Address: 10.42.73.10/8 (Link Up) Metric: 1 Administrative State: Enabled DR State: DR Backup DR Address: None Dead Interval: 40 Retransmit Time: 5 Interface Name: ipif2 IP Address: 123.234.12.34/24 (Link Up) Network Medium Type: BROADCAST Metric: 1 223

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

Match case Limit results 1 per page

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

223

show ospf ipif

Syntax

show ospf ipif {<ipif_name 12>}

Description

This command will display the current OSPF interface settings for the

specified interface name.

Parameters

<ipif_name 12>

−

The IP interface name for which to display the current

OSPF interface settings.

Restrictions

None.

Usage Example:

To display the current OSPF interface settings, for a specific OSPF interface:

DES-3800:admin#show ospf ipif ipif2

Command: show ospf ipif ipif2

Interface Name:

ipif2

IP Address: 123.234.12.34/24

((Link Up)

Network Medium Type: BROADCAST

Metric:

Area ID:

1.0.0.0

Administrative State:

Enabled

Priority:

DR State:

DR Address:

123.234.12.34

Backup DR Address:

None

Hello Interval:

Dead Interval:

Transmit Delay:

Retransmit Time:

Authentication:

None

Total Entries: 1

DES-3800:admin#

show ospf all

Purpose

Used to display the current OSPF settings of all the OSPF interfaces on

the Switch.

Syntax

show ospf all

Description

This command will display the current OSPF settings for all OSPF

interfaces on the Switch.

Parameters

None.

Restrictions

Only Administrator or Operator-level users can issue this command.

Usage example:

To display the current OSPF interface settings, for all OSPF interfaces on the Switch:

DES-3800:admin#show ospf all

Command: show ospf all

Interface Name: System

IP Address:

10.42.73.10/8 (Link Up)

Network Medium Type: BROADCAST

Metric:

Area ID:

0.0.0.0

Administrative State:

Enabled

Priority:

DR State:

DR Address:

10.42.73.10

Backup DR Address:

None

Hello Interval:

Dead Interval:

Transmit Delay:

Retransmit Time:

Authentication:

None

Interface Name:

ipif2

IP Address: 123.234.12.34/24 (Link Up)

Network Medium Type: BROADCAST

Metric: