Home » D-Link Manuals » Hubs & Switches » D-Link DES-3828 » Manual Viewer

D-Link DES-3828 Product Manual - Page 389

config pim register_probe_time, config pim, register_suppression_time

UPC - 790069276811

Add to My Manuals
Save this manual to your list of manuals

Page 389 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual config pim register_probe_time Purpose Syntax Description Parameters Restrictions Used to set a time to send a probe message from the DR to the RP before the Register Suppression time expires. config pim register_probe_time This command is used to set a time to send a probe message from the DR to the RP before the Register Suppression time expires. If a Register Stop message is received by the DR, the Register Suppression Time will be restarted. If no Register Stop message is received within the probe time, Register Packets will be resent to the RP. This command is for PIM-SM configurations only. - Configure this field to set a time to send a probe message from the DR to the RP before the Register Suppression time expires. The user may configure a time between 1-127 seconds with a default setting of 5 seconds. Only Administrator or Operator-level users can issue this command. Example usage: To configure the register probe time: DES-3800:admin#config pim register_probe_time 5 Command: config pim register_probe_time 5 Success. DES-3800:admin# config pim register_suppression_time Purpose Syntax Description Parameters Restrictions Used to configure the interval between the sending of register packets for the PIM protocol. config pim register_suppression_time This command is to be configured for the first hop router from the source. After this router sends out a register message to the RP, and the RP replies with a register stop message, it will wait for the time configured here to send out another register message to the RP. This command is for PIM-SM configurations only. - The user may set an interval time between 3-255 with a default setting of 60 seconds for the sending of register suppression time packets. The default value is 60 seconds. Only Administrator or Operator-level users can issue this command. Example usage: To configure the register suppression time: DES-3800:admin#config pim register_suppression_time 15 Command: config pim register_suppression time_15 Success. DES-3800:admin# 385

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

Match case Limit results 1 per page

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

385

config pim register_probe_time

Purpose

Used to set a time to send a probe message from the DR to the RP before

the Register Suppression time expires.

Syntax

config pim register_probe_time <value 1-127>

Description

This command is used to set a time to send a probe message from the DR

to the RP before the Register Suppression time expires. If a Register Stop

message is received by the DR, the Register Suppression Time will be

restarted. If no Register Stop message is received within the probe time,

configurations only.

Parameters

<value 1-127> -

Configure this field to set a time to send a probe message

from the DR to the RP before the Register Suppression time expires. The

user may configure a time between 1-127 seconds with a default setting of

5 seconds.

Restrictions

Only Administrator or Operator-level users can issue this command.

Example usage:

To configure the register probe time:

DES-3800:admin#config pim register_probe_time 5

Command: config pim register_probe_time 5

Success.

DES-3800:admin#

config pim

register_suppression_time

Purpose

Used to configure the interval between the sending of register packets for

the PIM protocol.

Syntax

config pim register_suppression_time <value 3-255>

Description

This command is to be configured for the first hop router from the source.

After this router sends out a register message to the RP, and the RP replies

with a register stop message, it will wait for the time configured here to send

out another register message to the RP. This command is for PIM-SM

configurations only.

Parameters

<value 3-255> -

The user may set an interval time between 3-255 with a

default setting of 60 seconds for the sending of register suppression time

packets. The default value is 60 seconds.

Restrictions

Only Administrator or Operator-level users can issue this command.

Example usage:

To configure the register suppression time:

DES-3800:admin#config pim register_suppression_time 15

Command: config pim register_suppression time_15

Success.

DES-3800:admin#