Home » D-Link Manuals » Hubs & Switches » D-Link DES-3828 » Manual Viewer

D-Link DES-3828 Product Manual - Page 415

create/delete dhcp pool manual_binding

UPC - 790069276811

Add to My Manuals
Save this manual to your list of manuals

Page 415 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual create/delete dhcp pool manual_binding Purpose Syntax Description Parameters Restrictions Specifies the distinct identification of the client in dotted-hexadecimal notation or harware address, for example, 0122.b708.1388,where 01 represents the Ethernet media type and the IP address pair. create dhcp pool manual_binding < ipaddr> hardware_address {type [ethernet | ieee802]} delete dhcp pool manual_binding [ | all] An address binding is a mapping between the IP address and MAC address of a client. The IP address of a client can be assigned manually by an administrator or assigned automatically from a pool by a DHCP server. The dynamic binding entry will be created when an IP address is assigned to the client from the pool network's address. For the create dhcp pool manual_binding command, if the type is not specified, the the type will be ethernet . For the match operation, the hardward type and the hardware address field in the protocol fields will be used to match against the entry. The IP address specified in the manual binding entry must be ranged within the network used by the DHCP pool. If the user specifies a conflict IP address, error message will be returned. If a number of manual binding entries are created, and the network address for the pool is changed such that conflict are generated, those manual binding entries which are conflict with the new network address will be automatically deleted. - Pool's name. - Hardware address. type - either eithernet or ieee802 can be specified. - IP address which will be assigned to specified client. Only Administrator or Operator-level users can issue this command. Usage Example: To configuring manual bindings: DES-3800:admin#create dhcp pool manual_binding engineering 10.10.10.1 hardware_address 00-80-C8-0202-02 type ethernet Command: create dhcp pool manual_binding engineering 10.10.10.1 hardware_address 00-80-C8-02-02-02 type ethernet Success. DES-3800:admin# 411

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

Match case Limit results 1 per page

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

411

create/delete dhcp pool manual_binding

Purpose

Specifies the distinct identification of the client in dotted-hexadecimal

notation or harware address, for example, 0122.b708.1388,where 01

represents the Ethernet media type and the IP address pair.

Syntax

create dhcp pool manual_binding <pool_name 12> < ipaddr>

hardware_address <macaddr> {type [ethernet | ieee802]} delete

dhcp pool manual_binding <pool_name 12> [<ipaddr> | all]

Description

An address binding is a mapping between the IP address and MAC

address of a client. The IP address of a client can be assigned

manually by an administrator or assigned automatically from a pool by

a DHCP server.

The dynamic binding entry will be created when an IP address is

assigned to the client from the pool network’s address.

For the create dhcp pool manual_binding command, if the type is not

specified, the the type will be ethernet . For the match operation, the

hardward type and the hardware address field in the protocol fields

will be used to match against the entry.

The IP address specified in the manual binding entry must be ranged

within the network used by the DHCP pool. If the user specifies a

conflict IP address, error message will be returned.

If a number of manual binding entries are created, and the network

address for the pool is changed such that conflict are generated,

those manual binding entries which are conflict with the new network

address will be automatically deleted.

Parameters

<pool_name 12>

- Pool’s name.

- Hardware address.

type

- either eithernet or ieee802 can be specified.

- IP address which will be assigned to specified client.

Restrictions

Only Administrator or Operator-level users can issue this command.

Usage Example:

To configuring manual bindings:

DES-3800:admin#create dhcp pool manual_binding

engineering 10.10.10.1 hardware_address 00-80-C8-02-

02-02 type ethernet

Command: create dhcp pool manual_binding engineering

10.10.10.1 hardware_address 00-80-C8-02-02-02 type

ethernet

Success.

DES-3800:admin#