Home » D-Link Manuals » Hubs & Switches » D-Link DES-3828 » Manual Viewer

D-Link DES-3828 Product Manual - Page 65

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual, current_config

UPC - 790069276811

Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual show config Purpose Syntax Description Parameters Restrictions Used to display the current or saved version of the configuration settings of the switch. show config [current_config | config_in_nvram | information] Use this command to display all the configuration settings that are saved to NV RAM or display the configuration settings as they are currently configured. Use the keyboard to list settings one line at a time (Enter), one page at a time (Space) or view all (a). The configuration settings are listed by category in the following order: 1. Basic (serial port, Telnet and web management status) 2. storm control 3. IP group management 4. syslog 5. QoS 6. port mirroring 7. traffic segmentation 8. port 9. port lock 10. 8021x 11. SNMPv3 12. management (SNMP traps RMON) 13. vlan 14. FDB (forwarding data base) 15. MAC address table notification 16. STP 17. SSH 18. SSL 19. ACL 20. SNTP 21. IP route 22. LACP 23. ARP 24. IP 25. IGMP snooping 26. access authentication control (TACACS etc.) current_config - Entering this parameter will display configurations entered without being saved to NVRAM. config_in_NVRAM - Entering this parameter will display configurations entered and saved to NVRAM. • config_id 1-2 - Adding this parameter will allow the user to specify which configuration file out of the possible 2 files, are to be displayed. information - Entering this parameter will display information regarding configuration files loaded and saved on the Switch. None. 61

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443