D-Link DES-3828 Product Manual - Page 71

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

67

ping

times <value 1-255>

- The number of individual ICMP echo

messages to be sent. A value of 0 will send an infinite ICMP echo

messages. The maximum value is 255. The default is 0.

timeout <sec 1-99>

- Defines the time-out period while waiting for a

response from the remote device. A value of 1 to 99 seconds can be

specified.

The default is 1 second

Restrictions

None.

Example usage:

To ping the IP address 10.48.74.121 four times:

DES-3800:admin#ping 10.48.74.121 times 4

Command: ping 10.48.74.121

Reply from 10.48.74.121, time<10ms




Ping statistics for 10.48.74.121

Packets: Sent =4, Received =4, Lost =0

DES-3800:admin#

traceroute

Purpose

Used to trace the routed path between the Switch and a destination

endstation.

Syntax

traceroute <ipaddr> {ttl <value 1-60> | port <value 30000-64900>

| timeout <sec 1-65535> | probe <value <1-9>}

Description

The traceroute command will trace a route between the Switch and

a give host on the network.

Parameters

<ipaddr>

- Specifies the IP address of the host.

ttl <value 1-60>

- The time to live value of the trace route request.

This is the maximum number of routers the traceroute command will

cross while seeking the network path between two devices.

port <value 30000-64900> -

The port number. Must be above

1024.The value range is from 30000 to 64900.

timeout <sec 1-65535>

- Defines the time-out period while waiting

for a response from the remote device. The user may choose an

entry between 1 and 65535 seconds.

probe <value 1-9>

- The probe value is the number of times the

Switch will send probe packets to the next hop on the intended

traceroute path. The default is 1.

Restrictions

Only Administrator-level users can issue this command.

Example usage:

To trace the routed path between the Switch and 10.48.74.121.

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

D-Link DES-3828 Product Manual - Page 71

traceroute, Packets: Sent =4, Received =4, Lost =0 - default ip address

Page 71 highlights