D-Link DGS-1008T User Guide
D-Link DGS-1008T Manual
 |
View all D-Link DGS-1008T manuals
Add to My Manuals
Save this manual to your list of manuals |
D-Link DGS-1008T manual content summary:
- D-Link DGS-1008T | User Guide - Page 1
DGS-1008T 8-Port 10/100/1000Mbps Gigabit Ethernet Switch User's Guide - D-Link DGS-1008T | User Guide - Page 2
TABLE OF CONTENTS ABOUT THIS GUIDE 1 T ERMS 1 OVERVIEW OF THIS USER'S GUIDE 1 INTRODUCTIO N 3 GIGABIT ETHERNET T ECHNOLOGY 3 SWITCHING T ECHNOLOGY 4 FEATURES 5 UNPACKING AND SETUP 7 UNPACKING 7 SETUP 7 DESKTOP OR SHELF INSTALLATION 8 RACK INSTALLATION 9 IDENTIFYING EXTERNAL COMPONENTS - D-Link DGS-1008T | User Guide - Page 3
) to refer to the 8-Port 10/100/1000Mbps Gigabit Ethernet Switch, and "switch" (first letter lower case) to refer to all Ethernet switches, including the 8-Port 10/100/1000Mbps Gigabit Ethernet Switch. Overview of this User's Guide ♦ Introduction. Describes the Switch and its features. ♦ Unpacking - D-Link DGS-1008T | User Guide - Page 4
of the 8-Port 10/100/1000Mbps Gigabit Ethernet Switch, as well as giving some background information about Gigabit Ethernet and switching technology. Gigabit Ethernet Technology Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the same packet structure, format, and support for CSMA - D-Link DGS-1008T | User Guide - Page 5
supports video conferencing, complex imaging, and similar data-intensive applications. Likewise, since data transfers occur 10 times faster than Fast Ethernet, servers outfitted with Gigabit Ethernet NIC's are able to perform 10 times the number of operations in the same amount of time. Switching - D-Link DGS-1008T | User Guide - Page 6
Auto-MDI Ethernet ports u Full/half duplex transfer mode for 10Mbps and 100Mbps u Full duplex transfer mode for 1000Mbps u Wire speed reception and transmission u Store-and-Forward switching method u Integrated address Look-Up Engine, supports 8K absolute MAC addresses u Supports 512K Bytes data - D-Link DGS-1008T | User Guide - Page 7
feet with adhesive backing ♦ One AC power cord ♦ User's guide If any item is found missing or damaged, please contact your local reseller for replacement. Setup The setup of the Switch can be performed using the following steps: ♦ The surface must support at least 5 kg. ♦ The power outlet should be - D-Link DGS-1008T | User Guide - Page 8
connector. ♦ Make sure that there is proper heat dissipation from and adequate ventilation around the Switch. Do not place heavy objects on the Switch. Desktop or Shelf Installation When installing the Switch on a desktop or shelf, the rubber feet included with the device must be first attached - D-Link DGS-1008T | User Guide - Page 9
19-inch rack, which can be placed in a wiring closet with other equipment. To install, attach the mounting brackets on the switch's front panel (one on each side) and secure them with the screws provided. Attaching the mounting brackets to the Switch Then, use the screws provided with the equipment - D-Link DGS-1008T | User Guide - Page 10
the front panel, rear panel and LED indicators of the Switch Front Panel The front panel of the Switch consists of 8 1000BASE-T ports and LED indicators. Front panel view of the Switch ♦ Eight Gigabit Ethernet ports of 10/100/1000Mbps AutoNegotiation interface. ♦ Comprehensive LED indicators that - D-Link DGS-1008T | User Guide - Page 11
provided power cord into this connector, and the male into a power outlet. Supported input voltages range from 100 ~ 240 VAC at 50 ~ 60 Hz. LED Indicators The LED indicators of the Switch include Power, 10/100/1000M Link/Act, and Full-Duplex/Collision. The following shows the LED indicators for the - D-Link DGS-1008T | User Guide - Page 12
unit: ♦ Power This indicator lights green when the Switch is receiving power, otherwise, it is off. Per port: ♦ 1000M LINK/ACT. These LED indicators are lit when there is a secure connection (or link) to 1000Mbps Gigabit Ethernet device at any of the ports. The LED indicators blink whenever there is - D-Link DGS-1008T | User Guide - Page 13
TECHNICAL SPECIFICATIONS Standards: Protocol: Data Transfer Rate: Topology: Network Cables: Number of Ports: General IEEE 802.3ab 1000BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3 10BASE-T CSMA Cat. 5, EIA/TIA568 100-ohm screened twistedpair (STP) Eight (8) 10/100/1000Mbps Auto-Negotiation ports 11 - D-Link DGS-1008T | User Guide - Page 14
: RAM Buffer: Filtering Address Table: Packet Filtering/Forwarding Rate: MAC Address Learning: Store-and-forward 512K Bytes per device 8K MAC address per device Full wire speed Self-learning, auto-aging 12
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
 |
 |
DGS-1008T
8-Port 10/100/1000Mbps
Gigabit Ethernet Switch
User’s Guide