D-Link DGS-3630-52PC WEB Reference Guide

D-Link DGS-3630-52PC Manual

Get D-Link DGS-3630-52PC PDF manuals and user guides View all D-Link DGS-3630-52PC manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DGS-3630-52PC manual content summary:

  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 1
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 2
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Table of Contents 1. Introduction...1 2. Basic CLI Commands ...9 3. Access Management Commands ...25 4. Authentication, Authorization, and Accounting (AAA) Commands 41 5. Basic IPv4 Commands ...61 6. Command Logging Commands ...
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 3
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 1. Introduction This manual's command descriptions are based on the software release 2.10, running in the OpenFlow Mode. The commands listed here are the subset of commands that are supported by the DGS-3630 Series switch. Audience This
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 4
    or loss of data and tells you how to avoid the problem. CAUTION: A caution indicates a potential for property damage, personal injury, or death. Command Descriptions The information pertaining to each command in this reference guide is presented using a number of template fields. The fields are
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 5
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide  Users with advanced user, power-user, operator or administrator level accounts will log into the Switch in the Privileged EXEC Mode. Therefore, the User EXEC
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 6
    15. Users logged in with this command mode can monitor all system information and change any system configuration settings mentioned in this Configuration Guide. The method to enter privileged EXEC mode at administrator level is to log into the Switch with a user account that has a privilege level
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 7
    -3630 Layer 3 Stackable Managed Switch CLI Reference Guide  The username admin privilege 15 command assigns module plugged into the open module slot of the Switch. The DGS-3630 Series switch doesn't support any open modules slots, thus this parameter will always be zero for this switch series.
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 8
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide In summary, the above example will configure the stacked ^marker Switch# Editing Features The command line interface of this switch supports the following keyboard keystroke editing features. Keystroke Delete Backspace Left Arrow Right
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 9
    ESC DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Escapes from the displaying page. Display Result Output Modifiers Results displayed by show commands can be filtered using the following parameters:  begin FILTER-STRING - This
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 10
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Switch#show running-config | exclude ! Building configuration... Current configuration : 1341 bytes line console line telnet line ssh interface Mgmt0 interface ethernet 1/0/1 interface ethernet 1/0/2 interface ethernet 1/0/3
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 11
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 2. Basic CLI Commands 2-1 help This command is used to display a brief description of the help system. Use the help command in any command mode. help
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 12
    Switch#help DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide The switch CLI provides advanced help feature. 1. Help is available when you are ready to enter a command argument (e.g. 'show ?') and want to know each possible
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 13
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Command Default Level Level: 1. Usage Guideline If the privileged level requires a password, enter it in the field provided. Only
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 14
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to change the privilege level of the active CLI login session to privilege level 1. Switch# show privilege Current privilege level
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 15
    Default None. DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Command Default Level Level: 1. Usage Guideline Use this command to change the login account. Three attempts are allowed to
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 16
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline For Console and Telnet access, when AAA is enabled, the line uses rules configured by the AAA module. When AAA is disabled, the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 17
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide This example shows how to configure the login method as login local. Switch# configure terminal Switch(config)# line console Switch(config-line)# login local Switch(
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 18
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Executing this command will return access to the highest mode in the CLI hierarchy. Example This
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 19
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 2-10 show history This command is used to or the Up Arrow key. The history buffer size is fixed at 20 commands. The function key instructions below display how to navigate the commands in the history buffer.  CTRL+P or the Up Arrow key
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 20
    to enter the reset configuration mode, please contact the technical support personnel. After entering the reset configuration mode, use the the password recovery feature. Switch(reset-config)# password-recovery This command will guide you to do the password recovery procedure. Do you want to update
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 21
    Default None. DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Command Default Level Level: 1. Usage Guideline If a specific type is not specified, all types of environment information will be
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 22
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide show unit [UNIT-ID] Parameters UNIT-ID (Optional) Specify the unit to display. Default None. Command Mode User/Privileged EXEC Mode. Command Default Level Level: 1.
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 23
    slot INDEX DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies the slot number to be displayed. For 15-minute based statistics count, the range is from 1 to 5. For 1-day based statistics count, the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 24
    show version DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Parameters None. Default None. Command Mode User/Privileged EXEC Mode. Command Default Level Level: 1. Usage Guideline Use this command to display the version information of
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 25
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, the normal range is the same as the operation range. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 26
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline This command is used to display the memory utilization information of the Switch including DRAM and flash. There are two kinds of statistics
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 27
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 3. Access Management Commands 3-1 banner login This command is used to enter banner login mode to configure the banner login message. Use the no form of
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 28
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide This example shows how to configure a login banner. The hash sign (#) is used as the delimiting character. Just the start delimiting character will be input
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 29
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 3-3 enable password This command is used to setup enable password to enter different privileged levels. Use the no form of this command to return the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 30
    -3630 Layer 3 Stackable Managed Switch CLI Reference Guide ip telnet server no ip telnet server Parameters None terminal Switch(config)# ip telnet server Switch(config)# 3-5 ip telnet service port This command is used to specify the service port for Telnet. Use the no form of this command to revert
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 31
    Stackable Managed Switch CLI Reference Guide Usage Guideline This command configures the TCP port number for Telnet access Example This example shows how to change the Telnet service port number to 3000. Switch# configure terminal Switch(config)# ip telnet service-port 3000 Switch(config)# 3-6 line
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 32
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is enabled. Command Use the no form of this command to disable the encryption. service password-encryption [7 | 15] no service password-encryption Parameters 7 15 (Optional) Specifies the password in
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 33
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The user account configuration information is stored in the running configuration file and can be applied to the system later. If the service password-encryption command is enabled, the password will be stored in the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 34
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display information about the terminal configuration parameter settings for the current terminal line. Switch#show terminal Terminal Settings: Length:
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 35
    3630 Layer 3 Stackable Managed Switch CLI Reference Guide 3-11 terminal length The command is used to . Valid entries are from 0 to 512. The default is 24 lines. A selection of 0's instructs the Switch to scroll continuously (no pausing). Output from a single command that overflows a single display
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 36
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 3-12 terminal speed This command is used to setup connection speed. Some baud rates available on the devices connected to the port might not be supported on the Switch. Example This example shows how to configure the serial port baud rate
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 37
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline This timer specifies the timeout for auto-logout sessions established by the line that is being configured. Example
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 38
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide The terminal width default command is available in the global configuration mode. The command setting does not affect the current existing terminal sessions but affect
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 39
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, no username-based authentication system is or in the plain-text form. If it is in the plain-text form, but the service password encryption is enabled, then the password will be converted to the encrypted form. If
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 40
    7 15 PASSWORD DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies the encrypted password based on SHA-1. The password length is fixed at 35 bytes. It is case-sensitive. The password is encrypted. If
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 41
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline Use this command to configure a customized banner to be displayed before the EXEC mode prompt. The customized banner
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 42
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure that the EXEC banner is not displayed on SSH line. Switch#configure terminal Switch(config)#line ssh Switch(
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 43
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 4. Authentication, Authorization, and Accounting (AAA) defined by the aaa group server tacacs+ command. Specifies to disable the accounting service. Default No AAA accounting method is configured. Command Mode Global Configuration Mode.
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 44
    -3630 Layer 3 Stackable Managed Switch CLI Reference Guide 4-2 aaa accounting exec This command is used server groups defined by the AAA group server command. Specifies to disable the accounting service. Default No AAA accounting method is configured. Command Mode Global Configuration Mode.
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 45
    -3630 Layer 3 Stackable Managed Switch CLI Reference Guide 4-3 aaa accounting system This command is used server groups defined by the AAA group server command. Specifies to disable the accounting service. Default No AAA accounting method is configured. Command Mode Global Configuration Mode.
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 46
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 4-4 aaa authentication enable This command is used to configure the default method list used for determining access to the privileged EXEC level. Use the no
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 47
    Parameters DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide default LIST-NAME METHOD1 [METHOD2...] Specifies to configure the default method list for login authentication. Specifies the name of the method list other than the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 48
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 4-6 aaa group server radius This command is used to enter the RADIUS group server configuration mode to associate server hosts with the group. Use the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 49
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Default There is no AAA group server. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline Use this command to enter the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 50
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable the AAA function. Switch#configure terminal Switch(config)# aaa new-model Switch(config)# 4-9 accounting commands This command is
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 51
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 4-10 accounting exec This command is used to configure the method list used for EXEC accounting for a specific line. Use the no form of this
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 52
    tacacs all sg NAME DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies to clear server counter information related to all TACACS hosts. Specifies to clear server counter information related to all hosts in a server group. Default
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 53
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 15. Usage Guideline For authentication via the method list to take effect, enable AAA first by using the aaa new-model
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 54
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure the RADIUS attribute 4 address as 10.0.0.21. Switch#configure terminal Switch(config)#radius-server attribute 4 10.0.0.21 Switch(
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 55
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide radius-server host IP-ADDRESS [auth-port PORT] [acct-port PORT] [timeout SECONDS] [retransmit COUNT] key [0 | 7] KEY-STRING no radius-server host IP-ADDRESS Parameters
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 56
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide server IP-ADDRESS no server IP-ADDRESS Parameters IP-ADDRESS Specifies the IPv4 address of the authentication server. Default By default, no server is configured.
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 57
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode TACACS+ Group Server Configuration Mode. Command Default Level Level: 15. Usage Guideline Use the aaa group server tacacs+ command to enter the TACACS+
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 58
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the AAA global state. Switch# show aaa AAA is enabled. Switch# 4-19 tacacs-server host This command is
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 59
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to create two TACACS+ server hosts with the different IP addresses. Switch#configure terminal Switch(config)# tacacs-server host 172.
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 60
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the server related statistics counters. Switch#show radius statistics RADIUS Server: 10.90.90.211: Auth-Port 1812,
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 61
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Pending Requests Timeouts Unknown Types Packets Dropped The number of RADIUS Request packets destined for this server that have not yet timed out or received a
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 62
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Display Parameters TACACS+ Server Socket Opens Socket Closes Total Packets Sent Total Packets Recv Reference Count IP address of the TACACS+ server. Number of successful
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 63
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 5. Basic IPv4 Commands 5-1 ip address This command is used to configure the IP address for the management interface. Use the no command to remove the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 64
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, the default gateway IP address is 0.0.0.0. Command Mode MGMT Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline IP packets destined
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 65
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the information of the IP interface. Switch#show ip interface mgmt_ipif 0 is enabled, Link status is down IP
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 66
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 6. Command Logging Commands 6-1 command logging enable This command is used to enable the command logging function. Use the no form of this command to disable
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 67
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 7. CPU Port Statistics Commands 7-1 debug show cpu port This command is used to display statistics for Layer 2 or Layer 3 control packets that are trapped to
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 68
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display all Layer 2 and Layer 3 protocol control packets that are trapped to the CPU. Switch#debug show cpu port
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 69
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to clear all statistics counters. Switch# debug clear cpu port Switch# 67
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 70
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 8. Debug Commands 8-1 debug enable This command is used to enable the debug message output option. Use the no form of this command to disable the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 71
    monitor DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies to output the debug messages to terminal such as Telnet or SSH. Default The default debug output is buffer. Command Mode Privileged EXEC Mode.
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 72
    -3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable the . error-log: Specifies to copy the error log information. tech-support: Specifies to copy the technical support information. Specifies the destination URL. Specifies the IPv4 address of the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 73
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to copy debug buffer information to a TFTP server (10.90.90.99). Switch# debug copy buffer tftp: //10.90.90.
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 74
    Default None. DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command Default Level Level: 15. Usage Guideline Use this command to clear the error log information. Example This example shows
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 75
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the debug buffer information. Switch# debug show buffer Debug buffer is empty Switch# This example shows how to
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 76
    Default None. Command Mode Privileged EXEC Mode. Command Default Level Level: 15. Usage Guideline Use this command to display technical support information. The technical support information is used to collect the Switch's information needed by the engineers to troubleshoot or analyze a problem. 74
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 77
    Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display technical support information of all the modules. Switch#debug show tech-support # DGS-3630-28PC Gigabit Ethernet Switch # Technical Support Information # # Firmware: Build 2.10.012 # Copyright
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 78
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the CPU utilization per process information. Switch#debug show cpu utilization Five seconds - 15 % One minute - 14 % Five
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 79
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 9. File System Commands 9-1 cd This command is used to change the current directory. cd [DIRECTORY-URL] Parameters DIRECTORY-URL (Optional) Specifies the URL of the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 80
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide delete FILE-URL Parameters FILE-URL Specifies the name of the file to be deleted. Default None. Command Mode Privileged EXEC Mode. Command Default Level
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 81
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline If URL is not specified, the in the file system and appears to the user as a subdirectory under the root directory. The supported file systems can be displayed as the user issues the dir command for the root directory. The
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 82
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to format an external Secure Digital (SD) card. Switch# format /d: All sectors will be erased, proceed? (y/n) [n] y Enter volume id (up
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 83
    Default None. DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command Default Level Level: 15. Usage Guideline Use this command to display the contents of a file in the file system.
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 84
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 15. Usage Guideline A file can be renamed to a file located either within the same directory or to another directory. Example This
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 85
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 9-9 show storage media-info This command is used to display the storage media's information. show storage media-info [unit UNIT-ID] Parameters unit UNIT-ID (
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 86
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 10. Interface Commands 10-1 clear counters This command is used to clear counters for the specified interfaces. clear counters {all | interface INTERFACE-ID [, | -]} Parameters all
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 87
    Default None. DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline The specified number with no spaces in between. The following keywords can be used for the supported interface types: 85
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 88
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide  Ethernet - Specifies the physical Ethernet switch port with all different media.  mgmt - Specifies the Ethernet interface used for the out-of-band management port. The
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 89
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 10-5 show counters This command is used to display interface information. show counters [interface INTERFACE-ID] Parameters interface INTERFACE-ID (Optional) Specifies the physical port
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 90
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the counters on port 1. Switch#show counters interface eth1/0/1 eth1/0/1 counters rxHCTotalPkts txHCTotalPkts rxHCUnicastPkts txHCUnicastPkts rxHCMulticastPkts txHCMulticastPkts rxHCBroadcastPkts
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 91
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide dot3StatsFrameTooLongs : 0 linkChange : 1 Switch# Display Parameters rxHCTotalPkts txHCTotalPkts rxHCUnicastPkts txHCUnicastPkts rxHCMulticastPkts txHCMulticastPkts rxHCBroadcastPkts txHCBroadcastPkts rxHCOctets txHCOctets
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 92
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide rxHCPkt1519to2047Octets rxHCPkt2048to4095Octets rxHCPkt4096to9216Octets txHCPkt64Octets txHCPkt65to127Octets txHCPkt128to255Octets txHCPkt256to511Octets txHCPkt512to1023Octets txHCPkt1024to1518Octets txHCPkt1519to1522Octets
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 93
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide txCollisions Transmit Total Collision Counter. Incremented by the total number of collisions experienced during the transmission. ifInErrors Received Error Packet Counter. Incremented for received packets
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 94
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide , (Optional) Specifies a series of interfaces or separates a range of interfaces from a previous range. No space is allowed before or after the comma. - (Optional) Specifies a range
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 95
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide This example shows how to display the interface information for port 1. Switch#show interfaces eth1/0/1 Eth1/0/1 is enabled link status is up Interface type: 1000BASE-T
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 96
    history 15_minute 1_day DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies to display the history counters. If this parameter is specified, the historical statistics counters will not be displayed. (Optional) Specifies to display the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 97
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide This example shows how to display switch ports error counters. Switch#show interfaces eth1/0/1,1/0/3 counters errors Port CrcAlign-Err / Undersize / Rcv-Err / InDiscard / Xmit-Err
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 98
    Excess-Col Runts Symbol-Err DeferredTx IntMacTx InDiscard DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Refer to the item "dot3StatsExcessiveCollisions" in Display Parameters in the show counters command. Incremented for each packet whose size is less than 64 bytes in
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 99
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide - (Optional) Specifies a range of interfaces. No space is allowed before or after the hyphen. Default None. Command Mode User/Privileged EXEC Mode. Command Default Level
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 100
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide show interfaces [INTERFACE-ID [, | -]] utilization [history {15_minute [slot 1-5 ] | 1_day [slot 1-2]}] Parameters INTERFACE-ID , utilization history 15_minute 1_day (Optional) Specifies the interface ID. If no interface
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 101
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the utilization of all the ports on the Switch. Switch#show interfaces utilization Port TX packets/sec RX
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 102
    , gbic DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies a series of interfaces or separates a range of interfaces from a previous range. No space is allowed before or after the comma. (Optional) Specifies a range
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 103
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Command Default Level Level: 1. Usage Guideline This command displays the description and link status of interfaces. Example This example
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 104
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 12. Usage Guideline The Physical port, loopback, VLAN, tunnel, and management interfaces are valid for this
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 105
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 11. IP Utility Commands 11-1 ping This command is used to diagnose basic network connectivity. ping [ip] IP-ADDRESS [length LENGTH] [count TIMES] [timeout SECONDS] [
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 106
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to ping the host with IP address 172.50.71.123. Switch#ping 172.50.71.123 count 5 Reply from
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 107
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 12. Jumbo Frame Commands 12-1 max-rcv-frame-size This command is used to configure the maximum Ethernet frame size allowed. Use the no form
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 108
    be available. Back up the configuration before changing the OpenFlow state. For more information, refer to the DGS-3630 Series CLI Reference Guide. Example This example shows how to disable the OpenFlow function. Switch#configure terminal Switch(config)#no openflow global enable WARNING: The command
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 109
    Guide 13-2 openflow controller This command is used to configure the OpenFlow controller. Use the no command to remove an OpenFlow controller. openflow controller IP-ADDRESS [service to initiate the Clear-Actions instruction for the table-miss entry. This instruction specifies that unknown packets
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 110
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, no table-miss entry is configured. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline The table-miss flow
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 111
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to clear the statistics information from the flow entry with the cookie ID of 0x64. Switch# clear openflow statistics cookie
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 112
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide show openflow table [detail] Parameters detail (Optional) INSTRUCTIONS : write_actions : group apply_actions : output, set_field clear_actions : (Support) goto_table : - metadata = (Not Support) , metadata_mask = (Not Support
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 113
    CLI Reference Guide This example shows how to display detailed OpenFlow table information. Switch#show openflow table detail active_entry = 0 lookup_count = (N/A) match_count = (N/A) max_entries = 2048 metadata match = (Not Support) metadata write = (Not Support) INSTRUCTIONS
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 114
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 13-7 show openflow flows This command is used to display information related to OpenFlow flows. show openflow flows Parameters None. Default None. Command Mode User/
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 115
    Layer 3 Stackable Managed Switch CLI Reference Guide show openflow status [features | port-description [interface INTERFACE-ID [,|-]]] Parameters features port-description interface INTERFACE-ID , - (Optional) Specifies to display the supporting status of OpenFlow features. (Optional) Specifies
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 116
    -3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the Supported Table statistics Supported Port statistics Supported Group statistics Supported Reassemble IP fragments Not supported Queue statistics Supported Port blocked Not supported
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 117
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 13-9 debug openflow This command is used to configure the OpenFlow debug function. Use the no command to disable the OpenFlow debug function. debug openflow [
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 118
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 14. Packet Debug Commands 14-1 debug clear cpu counter This command is used to clear packet counters including RX and TX of the CPU port.
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 119
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command Default Level Level: 15. Usage Guideline The command is used to check received packets in buffer. The system can
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 120
    Default None. DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command Default Level Level: 15. Usage Guideline This command is used to display packet counters including RX and TX of
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 121
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 15. Power over Ethernet (PoE) Commands (DGS-3630-28PC and DGS-3630-52PC Only) 15-1 clear poe statistic This command is used to clear the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 122
    , - status configuration statistics measurement DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies a series of interfaces or separate a range of interfaces from a previous range. No space is allowed before and after the comma. (Optional) Specifies a range
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 123
    Stackable Managed Switch CLI Reference Guide Display Parameters Interface State Class poe power-inline eth1/0/1-6 configuration Interface Admin Priority Legacy-Support Time-Range eth1/0/1 auto low disabled eth1/0/2 auto service order when power constrain happens within at the power unit. 121
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 124
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Legacy-Support Time-Range Enabled: The legacy PD can be detected. Disabled: The legacy PD cannot be detected. The time-range profile name which sets the activation
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 125
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the PoE power inline measurement. Switch#show poe power-inline eth1/0/1-6 measurement Interface --------eth1/0/1 eth1/0/2 eth1/0/3 eth1/0/4 eth1/0/5
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 126
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide This example shows how to display the PoE power inline LLDP classification. Switch# show poe power-inline lldp-classification Interface eth1/0/1 PSE TX information: Power
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 127
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Power type Power source Power priority PD requested power value PSE allocated power value The power type field which is in the Power via MDI
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 128
    Layer 3 Stackable Managed Switch CLI Reference Guide Display Parameters Unit Delivered Power budget Usage- provided power of lower priority PD. Disabled: The power management mode is first in first serviced. Enabled: The trap is sent when the PoE usage threshold exceeds the specified value. Disabled
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 129
    Default None. DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Command Default Level Level: 1. Usage Guideline Use this command to display the PD alive check settings on the specified
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 130
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 16. Reboot Commands 16-1 reboot This command is used to reboot the Switch. reboot [force_agree] Parameters force_agree (Optional) Specifies to restart the Switch without confirmation.
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 131
    3630 Layer 3 Stackable Managed Switch CLI Reference Guide save_before_reboot specified time on the current day shutdown, the reboot schedule will be deleted automatically. Moreover, if the Switch was manually rebooted or powered off before the reboot schedule takes effect, the specified reboot
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 132
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline This command is used to display the reboot schedule configuration. Example This example shows how to display the reboot
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 133
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 17. Secure Shell (SSH) Commands 17-1 crypto key generate This command is used to generate the RSA or DSA key pair. crypto key generate {rsa [
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 134
    dsa DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Specifies to delete the RSA key pair. Specifies to Server. If both RSA and DSA key pairs are deleted, the SSH server will not be in service. Example This example shows how to delete the RSA key. Switch# crypto key zeroize rsa Do you
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 135
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline Use this command to configure the SSH server parameters on the Switch. The authentication retry number specifies the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 136
    -3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable the SSH server function. Switch# configure terminal Switch(config)# ip ssh server Switch(config)# 17-5 ip ssh service-port This command is used to specify the service port for SSH. Use the no form of
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 137
    Default None. DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command Default Level Level: 12. Usage Guideline Use this command to display the RSA or DSA public key pairs. Example
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 138
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the SSH configuration settings. Switch# show ip ssh IP SSH server IP SSH service port SSH server mode Authentication timeout Authentication retries : Enabled : 22 : V2 : 120 secs : 3 times
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 139
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Display Parameters SID Ver Cipher Userid Client IP Address A unique number that identifies the SSH session. Indicates the SSH version of this session. The cryptographic /
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 140
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide To authenticate a user via SSH public key authentication, copy the user's public key file to file system. When the user tries to log into the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 141
    Guide 18. Switch Port Commands 18-1 speed This command is used to configure the physical port interface's speed settings. Use the no form of this command to revert to the default setting. NOTE: 10G does not support speed to 1000Mbps and the user must manually set that the port operates as master or
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 142
    Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline If the specified speed is not supported by the hardware, error messages will mode combined with the specified speeds. The half-duplex mode is not supported on the Switch. For 10GBASE-R connections, if auto-negotiation is enabled,
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 143
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to enable speed auto-downgrade. Switch#configure terminal Switch(config)#interface eth1/0/5 Switch(config-if)#speed auto-downgrade Switch(config-if)# 141
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 144
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 19. System File Management Commands 19-1 boot config This command is used to specify the file that will be used as the configuration file for
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 145
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline When using the boot image command, the associated specified boot image file will
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 146
    Default None. DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command Default Level Level: 15. Usage Guideline Use this command to clear the system's configuration retained in DRAM. The configuration
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 147
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline Use this command to clear the system's configuration, including stacking information. The configuration data will revert to the default settings and then save
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 148
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode Privileged EXEC Mode. Command Default Level Level: 15. Usage Guideline This command is used to execute the indicated configuration file to replace the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 149
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide This example shows how to download the "config.cfg" from the FTP server and replace the current running configuration with it. Execute the command immediately
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 150
    LOCATION USER-NAME PASSWORD DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide configuration into the NVRAM and the file name will be the same as the file name specified with the boot config command. If flash: [PATH-
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 151
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure the Switch's running configuration by using the increment method using the configuration called "switch-config.cfg" that is
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 152
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide This example shows how to download an image file from the TFTP server. Switch#copy tftp: //192.168.1.123/2.10.012.had flash: image.had
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 153
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide This example shows how to download an image file from the SFTP server to all units in the stack. Switch# copy sftp: //10.90.90.
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 154
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display system boot information. Switch# show boot Unit 1 Boot image: c:/bootimage.had Boot config: c:/def_usr.cfg Switch# 19-8 show
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 155
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the content of the running configuration file. Switch#show running-config Building configuration... Current configuration : 1507 bytes ! DGS-
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 156
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to display the content of the startup configuration file. Switch#show startup-config ! DGS-3630-28PC Gigabit Ethernet Switch ! Configuration ! !
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 157
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 20. System Log Commands 20-1 clear logging This command is used to delete log messages in the system logging buffer. clear logging Parameters None. Default
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 158
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline To enable the logging of system messages, use the logging on command in the global configuration mode. This
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 159
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, the severity level is warning (4). Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline The system messages can be
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 160
    discriminator DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide (Optional) Specifies to filter the message to be sent to the local console based on the discriminator. Default By default, this option is disabled. Command
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 161
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Default By default, this option is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline The system messages can be logged
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 162
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide includes SEVERITY-LIST (Optional) Specifies to include the matching message. The unmatched messages are filtered. Enter the list of severity levels to be included after
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 163
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide FACILITY-NUM FACILITY-NAME discriminator NAME port UDP-PORT (Optional) Specifies a decimal value from 0 to 23 to represent the facility. If not specified, the default
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 164
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 19 local3 20 local4 21 local5 22 local6 23 local7 Local use 3 (local3). Local use 4 (local4). Local use 5 (local5). Local use 6 (local6). Local use 7 (local7).
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 165
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide If the command is issued without options, the system will display up to 200 entries starting from the latest message. Example This example shows how
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 166
    Stackable Managed Switch CLI Reference Guide 21. Time Commands 21-1 clock set This command is used to manually set the system's clock. clock will be replaced by the new synced clock. Example This example shows how to manually set the software clock to 6:00 p.m. on Jul 4, 2013. Switch# clock set 18
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 167
    Default None. DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Mode User/Privileged EXEC Mode. Command Default Level Level: 1. Usage Guideline This command also indicates the clock's source. The clock source can be "No
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 168
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 22. Virtual LAN (VLAN) Commands 22-1 show vlan This command is used to display the parameters for all configured VLANs or one VLAN on the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 169
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide This example shows how to display the PVID, ingress checking, and acceptable frame type information for ports 1 to 3. Switch# show vlan interface eth1/0/1-3 eth1/0/1 VLAN
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 170
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Usage Guideline The command takes effect when the interface is set to access mode. The VLAN specified as the access VLAN does not need to
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 171
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide When the allowed VLAN is only specified as the VLAN ID, the succeeding command will overwrites the previous command. If the new untagged allowed VLAN
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 172
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Example This example shows how to configure port 1 can be a tagged member of other VLANs configured. The purpose of a trunk port is to support the switch-to-switch connection. When the switch-port mode is changed, the VLAN related setting
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 173
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide 22-6 switchport trunk allowed vlan This command is used to configure the VLANs that are allowed to receive and send traffic on the specified interface
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 174
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide switchport trunk native vlan {VLAN-ID | tag} no switchport trunk native vlan [tag] Parameters VLAN-ID tag Specifies the native VLAN for a trunk port. Specifies
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 175
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide - (Optional) Specifies a range of VLANs. No space is allowed before and after the hyphen. Default The VLAN ID 1 exists in the system as the default
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 176
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Command Default Level Level: 12. Usage Guideline Use this command to specify the name of a VLAN. The VLAN name must be unique within the administrative
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 177
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Appendix A - Password Recovery Procedure This section describes the procedure for resetting passwords on the D-Link DGS-3630 Series switch. Authenticating any user who tries to
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 178
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Appendix B - System Log Entries The following table lists all possible entries and their corresponding meanings that will appear in the System Log of this Switch.
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 179
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Event Description: Enable privilege failure. Log Message: Enable privilege failed through [from ] authenticated by AAA (Username: )
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 180
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide interface-id: It indicates the port number of the client authenticated. acl-script: The assign ACL script that authorized by from RADIUS server. Configuration/Firmware
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 181
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide macaddr: Represent client MAC address. serverIP: Server IP address. pathFile: Path and file name on server. Event Description: Configuration downloaded successfully. Log Message: [Unit ,]
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 182
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Log Message: [Unit ,]Downloaded by unsuccessfully. (Username: [, IP: , MAC: ], Server IP: , File Name: ) Parameters Description: unitID: The unit
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 183
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide username: Represent current login user. Event Description: Login through Telnet successfully. Log Message: Successful login through Telnet (Username: , IP: ) Parameters Description: username: Represent
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 184
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Log Message: TCP session is successfully connected with the controller : Parameters Description: ipaddr: It indicates the controller's IP address. port: It indicates the
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 185
    Peripheral DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Log Description Event Description: Fan Recovered. Log Message: Unit , back to normal Parameters Description: Unit : The unit ID. :
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 186
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Parameters Description: unit-id: The box ID. percentage: Usage threshold. Event Description: Total power usage threshold is recovered. Log Message: Unit usage threshold <
  • D-Link DGS-3630-52PC | WEB Reference Guide - Page 187
    DGS-3630 Layer 3 Stackable Managed Switch CLI Reference Guide Event Description: SSH server is enabled. Log Message: SSH server is enabled Event Description: SSH server is disabled. Log Message: SSH server is disabled Informational Informational 185
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187