D-Link DIR-655 Product Manual

D-Link DIR-655 - Xtreme N Gigabit Router Wireless Manual

Get D-Link DIR-655 - Xtreme N Gigabit Router Wireless PDF manuals and user guides
UPC - 790069298561
View all D-Link DIR-655 manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DIR-655 manual content summary:

  • D-Link DIR-655 | Product Manual - Page 1
  • D-Link DIR-655 | Product Manual - Page 2
    are trademarks or registered trademarks of their respective companies. Copyright © 2008-2010 by D-Link Canada, Inc. All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Canada, Inc. D-Link DIR-655 User Manual i
  • D-Link DIR-655 | Product Manual - Page 3
    Firewall Settings 36 Application Level Gateway Configuration 37 Routing...38 Advanced Wireless Settings 39 WISH Settings 40 Wi-Fi Protected Setup (WPS 41 Advanced Network Settings 42 UPnP...42 Internet Ping Block 42 Internet Port Speed 42 Multicast Streams 42 D-Link DIR-655 User Manual ii
  • D-Link DIR-655 | Product Manual - Page 4
    ...61 Email Settings 62 System Settings 63 Update Firmware 64 DDNS...65 System Check 66 Schedules 67 Device Information 68 Log...69 Stats...70 Active Sessions 70 Wireless...71 D-Link DIR-655 User Manual Support...72 Wireless Security 73 What is WPA 73 Wireless Security Setup Wizard 74
  • D-Link DIR-655 | Product Manual - Page 5
    OCvoenrvtieenwts D-Link DIR-655 Xtreme N™ Router with 3 Detachable Antennas Power Adapter CAT 5 Ethernet Cable CD-ROM Note: Using a power supply with a different voltage rating than the one included with the DIR-655 will cause damage and void the warranty. D-Link DIR-655 User Manual 1
  • D-Link DIR-655 | Product Manual - Page 6
    Make sure you have the latest version of Java installed. Visit www.java.com to download the latest version. CD Installation Wizard Requirements Computer with the following: • Windows 7, Vista®, or XP with Service Pack 2 • An installed Ethernet adapter • CD-ROM drive D-Link DIR-655 User Manual 2
  • D-Link DIR-655 | Product Manual - Page 7
    throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely affect wireless signal range. D-Link DIR-655 User Manual 3
  • D-Link DIR-655 | Product Manual - Page 8
    supports multiple and concurrent IPSec and PPTP sessions, so users behind the DIR-655 can securely access corporate networks. • User-friendly Setup Wizard - Through its easy-to-use Web-based user interface, the DIR-655 lets you control what information is accessible to those on the wireless network
  • D-Link DIR-655 | Product Manual - Page 9
    cable or DSL modem. 3 USB Connect a USB 1.1 or 2.0 flash drive to configure the wireless settings using WCN. 4 Reset Pressing the Reset button restores the router to its original factory default settings. 5 Power Receptor Receptor for the supplied power adapter. D-Link DIR-655 User Manual 5
  • D-Link DIR-655 | Product Manual - Page 10
    Local Network's LED A solid light indicates a connection to an Ethernet-enabled computer on ports 1-4. This LED blinks during data transmission. 5 WCN LED Insert a USB flash drive with WCN information. The LED will blink 3 times if it successfully transfers the wireless settings. D-Link DIR-655
  • D-Link DIR-655 | Product Manual - Page 11
    This section will walk you through the installation process. Placement of the router is very important. sure you disable or uninstall any PPPoE software such as WinPoet, Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet. D-Link DIR-655 User Manual 7
  • D-Link DIR-655 | Product Manual - Page 12
    ceiling fans, lights, and home security systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits a signal even if the phone in not in use. D-Link DIR-655 User Manual 8
  • D-Link DIR-655 | Product Manual - Page 13
    In the run box type "D:\autorun.exe" (where D: represents the drive letter of your CD-ROM drive). When the autorun screen appears, click Install. Note: It is recommended to write down the SSID and Security Key, followed by the login password on the provided CD holder. D-Link DIR-655 User Manual 9
  • D-Link DIR-655 | Product Manual - Page 14
    NetBIOS name in the address bar (http:// dlinkrouter). Select Admin from the drop-down menu and then enter your password. The password is left blank by default. If you get a Page Cannot be Displayed error, please refer to the Troubleshooting section for assistance. D-Link DIR-655 User Manual 10
  • D-Link DIR-655 | Product Manual - Page 15
    to enter your settings without running the wizard, click Manual Configuration and skip to page 15. Click Launch Internet Connection Setup Wizard to begin. If you want to configure your wireless settings, click Launch Wireless Security Setup Wizard and skip to page 74. D-Link DIR-655 User Manual 11
  • D-Link DIR-655 | Product Manual - Page 16
    Section 3 - Configuration Click Next to continue. Create a new password and then click Next to continue. Select your time zone from the drop-down menu and then click Next to continue. Select the type of Internet connection you use and then click Next to continue. D-Link DIR-655 User Manual 12
  • D-Link DIR-655 | Product Manual - Page 17
    subnet mask, gateway, and DNS server addresses. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. If you selected PPTP, enter your PPTP username and password. Click Next to continue. D-Link DIR-655 User Manual 13
  • D-Link DIR-655 | Product Manual - Page 18
    . Click Connect to save your settings. Once the router is finished rebooting, click Continue. Please allow 1-2 minutes to connect. Close your browser window and reopen it to test your Internet connection. It may take a few tries to initially connect to the Internet. D-Link DIR-655 User Manual 14
  • D-Link DIR-655 | Product Manual - Page 19
    MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC's MAC Address button to replace the Internet port's MAC address with the MAC address of your Ethernet card. D-Link DIR-655 User Manual 15
  • D-Link DIR-655 | Product Manual - Page 20
    DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. My Internet Connection: Select PPPoE (Username/Password) from the drop-down menu. Address Mode: Select Static if your ISP assigned you the IP address, subnet
  • D-Link DIR-655 | Product Manual - Page 21
    (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In
  • D-Link DIR-655 | Product Manual - Page 22
    you with a username and password. This option is typically used for DSL services. Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. L2TP IP Address: Enter the L2TP IP address supplied by your ISP
  • D-Link DIR-655 | Product Manual - Page 23
    MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC's MAC Address button to replace the Internet port's MAC address with the MAC address of your Ethernet card. D-Link DIR-655 User Manual 19
  • D-Link DIR-655 | Product Manual - Page 24
    Indicates the channel setting for the DIR-655. By default the channel is set to 6. The Channel can be changed to fit the channel setting for an existing wireless network or to customize the wireless network. If you enable Auto Channel Scan, this option will be greyed out. 802.11 Mode: Select one of
  • D-Link DIR-655 | Product Manual - Page 25
    allow you to change the local network settings of the router and to configure the DHCP settings. IP Address: Enter the IP address of the router. The default IP address is 192.168.0.1. If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to get
  • D-Link DIR-655 | Product Manual - Page 26
    if the'Learn NetBIOS information from WAN' is activated." NetBIOS Mode Type: Select the different type of NetBIOS node: Broadcast only, Point-to-Point, Mixed-mode, and Hybrid. Primary/Secondary WINS Enter your Primary (and Secondary) WINS IP address(es). IP Address: D-Link DIR-655 User Manual 22
  • D-Link DIR-655 | Product Manual - Page 27
    may still need to extend the "DHCP IP Address Range" to address the issue, it is located in the DHCP Server section. Reserve: The Reserve option converts this dynamic IP allocation into a DHCP Reservation and adds the corresponding entry to the DHCP Reservations List. D-Link DIR-655 User Manual 23
  • D-Link DIR-655 | Product Manual - Page 28
    to share the USB device through the router. USB Settings: Choose between these two configuration: Network USB and WCN Configuration. Network USB: Please set the Network USB Detection interval time. Note: Please see the SharePort Manual on the CD for more information. D-Link DIR-655 User Manual 24
  • D-Link DIR-655 | Product Manual - Page 29
    are pre-defined virtual services already in the table. You may use them by enabling them and assigning the server IP to use that particular virtual service. For a list of ports for common applications, please visit http://support.dlink.com/faq/view.asp?prod_id=1191. D-Link DIR-655 User Manual 25
  • D-Link DIR-655 | Product Manual - Page 30
    > Inbound Filter page. Schedule: The schedule of time when the Virtual Server Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section. D-Link DIR-655 User Manual 26
  • D-Link DIR-655 | Product Manual - Page 31
    > Inbound Filter page. Schedule: The schedule of time when the Virtual Server Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section. D-Link DIR-655 User Manual 27
  • D-Link DIR-655 | Product Manual - Page 32
    through NAT (Network Address Translation). Special Applications makes some of these applications work with the DIR-655. If you be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section. D-Link DIR-655 User Manual
  • D-Link DIR-655 | Product Manual - Page 33
    Frame Relay Network causes the measured uplink speed to be reported slightly lower than before on such connections, but gives much better results. Detected xDSL: When Connection Type is set to automatic, the automatically detected connection type is displayed here. D-Link DIR-655 User Manual 29
  • D-Link DIR-655 | Product Manual - Page 34
    the drop-down menu. MAC Address: Enter the MAC address you would like to filter. To find the MAC address on a computer, please refer to the Networking Basics section in this manual. DHCP Client: Select a DHCP client from the drop-down menu and click
  • D-Link DIR-655 | Product Manual - Page 35
    to approved sites, limit web access based on time or dates, and/or block access from applications like P2P utilities or games. Add Policy: Click the Add Policy button to start the Access Control Wizard. Click Next to continue with the wizard. Access Control Wizard D-Link DIR-655 User Manual 31
  • D-Link DIR-655 | Product Manual - Page 36
    the drop-down menu and then click Next to continue. Enter the following information and then click Next to continue. • Address Type - Select IP address, MAC address, or Other Machines. • IP Address - Enter the IP address of the computer you want to apply the rule to. D-Link DIR-655 User Manual 32
  • D-Link DIR-655 | Product Manual - Page 37
    IP address. Dest IP End - Enter the ending IP address. Protocol - Select the protocol. Dest Port Start - Enter the starting port number. Dest Port End - Enter the ending port number. To enable web logging, click Enable. Click Save to save the access control rule. D-Link DIR-655 User Manual
  • D-Link DIR-655 | Product Manual - Page 38
    blocked and click Save Settings. The text to be blocked will appear in the list. To delete the text, click Clear the List Below. Website URL/Domain: Enter the keywords or URLs that you want to block (or allow). Any URL with the keyword in it will be blocked. D-Link DIR-655 User Manual 34
  • D-Link DIR-655 | Product Manual - Page 39
    an IP address range. Inbound Settings at the top to save the settings. Inbound Filter Rules List: This section will list any rules that are created. You may click the Edit icon to change the settings or enable/disable the rule, or click the Delete icon to remove the rule. D-Link DIR-655 User Manual
  • D-Link DIR-655 | Product Manual - Page 40
    Configuration Firewall Settings A firewall protects your network from the outside world. The D-Link DIR-655 offers IP address automatically using DHCP, be sure to make a static reservation on the Basic > DHCP page so that the IP address of the DMZ machine does not change. D-Link DIR-655 User Manual
  • D-Link DIR-655 | Product Manual - Page 41
    over IP) to communicate across NAT. Some VoIP applications and devices have the ability to discover NAT devices and work around them. This ALG may interfere with the operation of such devices. If you are having trouble making VoIP calls, try turning this ALG off. D-Link DIR-655 User Manual 37
  • D-Link DIR-655 | Product Manual - Page 42
    option is an advanced method of customizing specific routes of data through your network. Destination IP: Enter the IP address of packets that will take this route : Select the interface that the IP packet must use to transit out of the router when this route is used. D-Link DIR-655 User Manual 38
  • D-Link DIR-655 | Product Manual - Page 43
    your wireless network. This will improve the quality of video and voice applications for your wireless clients. Short GI: Check this box to reduce the guard interval time therefore increasing the data capacity. However, it's less reliable and may create higher data loss. D-Link DIR-655 User Manual
  • D-Link DIR-655 | Product Manual - Page 44
    . For most applications, the priority classifiers ensure the right priorities and specific WISH Rules are not required. WISH supports overlaps between rules. If more than one rule matches for a specific message flow, the rule with the highest priority will be used. D-Link DIR-655 User Manual 40
  • D-Link DIR-655 | Product Manual - Page 45
    the wireless network if you have entered the PIN, or pressed a special Wi-Fi Protected Setup button on the device. The router acts as a registrar for the network, although other devices may act as a registrar as well. Add Wireless Device Start the wizard. Wizard: D-Link DIR-655 User Manual 41
  • D-Link DIR-655 | Product Manual - Page 46
    /100/1000Mbps. Some older cable or DSL modems may require you to set the port speed to 10Mbps. UPnP Internet Ping Block Internet Port Speed Multicast Streams Multicast streams: Check the box to allow multicast traffic to pass through the router from the Internet. D-Link DIR-655 User Manual 42
  • D-Link DIR-655 | Product Manual - Page 47
    name (SSID) that is different from your main wireless network. Enable Routing Between Check to allow network connectivity between the different Zones: zones created. Security Mode: Select the type of security or encryption you would like to enable for the guest zone. D-Link DIR-655 User Manual 43
  • D-Link DIR-655 | Product Manual - Page 48
    Section 3 - Configuration IPv6 Link-Local Connectivity My IPv6 Connection: Select Link-Local Only from the drop-down menu. LAN IPv6 Address Displays the IPv6 address of the router. Settings: D-Link DIR-655 User Manual 44
  • D-Link DIR-655 | Product Manual - Page 49
    IPv6 Address Range Start: Enter the start IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address Range End: Enter the end IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address Lifetime: Enter the IPv6 Address Lifetime (in minutes). D-Link DIR-655 User Manual 45
  • D-Link DIR-655 | Product Manual - Page 50
    's LAN Link-Local Address. Enable Autoconfiguration: Check to enable the Autoconfiguration feature. Autoconfiguration Type: Select Stateless. Refer to the previous page for Stateful. Router Advertisement Enter the Router Advertisement Lifetime (in minutes). Lifetime: D-Link DIR-655 User Manual 46
  • D-Link DIR-655 | Product Manual - Page 51
    IPv6 Address Range Start: Enter the start IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address Range End: Enter the end IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address Lifetime: Enter the IPv6 Address Lifetime (in minutes). D-Link DIR-655 User Manual 47
  • D-Link DIR-655 | Product Manual - Page 52
    's LAN Link-Local Address. Enable Autoconfiguration: Check to enable the Autoconfiguration feature. Autoconfiguration Type: Select Stateless. Refer to the previous page for Stateful. Router Advertisement Enter the Router Advertisement Lifetime (in minutes). Lifetime: D-Link DIR-655 User Manual 48
  • D-Link DIR-655 | Product Manual - Page 53
    . IP Address: Enter the IP address (Static PPPoE only). User Name: Enter your PPPoE user name. Password: Enter your PPPoE password and then retype the password in the next box. Service Name: Enter the ISP Service Name (optional). Reconnection Mode: Select either Always-on, On-Demand, or Manual
  • D-Link DIR-655 | Product Manual - Page 54
    IPv6 Address Range Start: Enter the start IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address Range End: Enter the end IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address Lifetime: Enter the IPv6 Address Lifetime (in minutes). D-Link DIR-655 User Manual 50
  • D-Link DIR-655 | Product Manual - Page 55
    . IP Address: Enter the IP address (Static PPPoE only). User Name: Enter your PPPoE user name. Password: Enter your PPPoE password and then retype the password in the next box. Service Name: Enter the ISP Service Name (optional). Reconnection Mode: Select either Always-on, On-Demand, or Manual
  • D-Link DIR-655 | Product Manual - Page 56
    Section 3 - Configuration Enable Autoconfiguration: Check to enable the Autoconfiguration feature. Autoconfiguration Type: Select Stateful (DHCPv6) or Stateless. Router Advertisement Lifetime: Enter the Router Advertisement Lifetime (in minutes). D-Link DIR-655 User Manual 52
  • D-Link DIR-655 | Product Manual - Page 57
    IPv6 Address Range Enter the start IPv6 Address for the DHCPv6 range for your Start: local computers. IPv6 Address Range Enter the end IPv6 Address for the DHCPv6 range for your End: local computers. IPv6 Address Lifetime: Enter the IPv6 Address Lifetime (in minutes). D-Link DIR-655 User Manual 53
  • D-Link DIR-655 | Product Manual - Page 58
    's LAN Link-Local Address. Enable Autoconfiguration: Check to enable the Autoconfiguration feature. Autoconfiguration Type: Select Stateless. Refer to the previous page for Stateful. Router Advertisement Enter the Router Advertisement Lifetime (in minutes). Lifetime: D-Link DIR-655 User Manual 54
  • D-Link DIR-655 | Product Manual - Page 59
    Address Range Enter the start IPv6 Address for the DHCPv6 range for your Start: local computers. IPv6 Address Range Enter the end IPv6 Address for the DHCPv6 range for your End: local computers. Pv6 Address Lifetime: Enter the Router Advertisement Lifetime (in minutes). D-Link DIR-655 User Manual
  • D-Link DIR-655 | Product Manual - Page 60
    LAN Link-Local Address. Enable Check to enable the Autoconfiguration feature. Autoconfiguration: Autoconfiguration Type: Select Stateful (DHCPv6) or Stateless. Refer to the next page for Stateless. IPv6 Address Lifetime: Enter the IPv6 Address Lifetime (in minutes). D-Link DIR-655 User Manual 56
  • D-Link DIR-655 | Product Manual - Page 61
    's LAN Link-Local Address. Address: Enable Check to enable the Autoconfiguration feature. Autoconfiguration: Autoconfiguration Select Stateless. Refer to the previous page for Stateful. Type: IPv6 Address Lifetime: Enter the Router Advertisement Lifetime (in minutes). D-Link DIR-655 User Manual 57
  • D-Link DIR-655 | Product Manual - Page 62
    Address Lifetime: Enter the start IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address Range Enter the end IPv6 Address for the DHCPv6 range for your Start: local computers. IPv6 Address Lifetime: Enter the Router Advertisement Lifetime (in minutes). D-Link DIR-655 User Manual
  • D-Link DIR-655 | Product Manual - Page 63
    network can browse the built-in web pages to perform Administrator tasks. This feature enables you to perform Administrator tasks from the remote (Internet) host. The port number used to access the DIR-655. Remote Admin Inbound Example: http://x.x.x.x:8080 whereas x.x.x.x is the Internet IP address
  • D-Link DIR-655 | Product Manual - Page 64
    Used: Enter the NTP server or select one from the drop-down menu. Manual: To manually input the time, enter the values in these fields for the Year, Month, Day, Hour, Minute, and Second and then click Set Time. You can also click Copy Your Computer's Time Settings. D-Link DIR-655 User Manual 60
  • D-Link DIR-655 | Product Manual - Page 65
    box to send the router logs to a SysLog Server. Server: SysLog Server IP Address: The address of the SysLog server that will be used to send the logs. You may also select your computer from the dropdown menu (only if receiving an IP address from the router via DHCP). D-Link DIR-655 User Manual 61
  • D-Link DIR-655 | Product Manual - Page 66
    option is enabled when On Schedule is selected. You can select a schedule from the list of defined schedules. To create a schedule, go to Tools > Schedules. D-Link DIR-655 User Manual 62
  • D-Link DIR-655 | Product Manual - Page 67
    the router was shipped from the factory. Any settings that have not been saved will be lost, including any rules that you have created. If you want to save the current router configuration settings, use the Save button above. Reboot Device: Click to reboot the router. D-Link DIR-655 User Manual 63
  • D-Link DIR-655 | Product Manual - Page 68
    : Check Automatically Check Online for Latest Firmware Version to have the router check automatically to see if there is a new firmware upgrade. Check Email Notification of Newer Firmware Version to have the router send an email when there is a new firmware available. D-Link DIR-655 User Manual 64
  • D-Link DIR-655 | Product Manual - Page 69
    from the drop down menu. Host Name: Enter the Host Name that you registered with your DDNS service provider. Username or Key: Enter the Username for your DDNS account. Password or Key: Enter the Password for your DDNS account. Timeout: Enter a time (in hours). D-Link DIR-655 User Manual 65
  • D-Link DIR-655 | Product Manual - Page 70
    Section 3 - Configuration System Check Ping Test: The Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP Address that you wish to Ping, and click Ping. Ping Results: The results of your ping attempts will be displayed here. D-Link DIR-655 User Manual 66
  • D-Link DIR-655 | Product Manual - Page 71
    . Save: Click Save to save your schedule. You must click Save Settings at the top for your schedules to go into effect. Schedule Rules List: The list of schedules will be listed here. Click the Edit icon to make changes or click the Delete icon to remove the schedule. D-Link DIR-655 User Manual 67
  • D-Link DIR-655 | Product Manual - Page 72
    wireless settings such as SSID and Channel. LAN Computers: Displays computers and devices that are connected to the router via Ethernet and that are receiving an IP address assigned by the router (DHCP). IGMP Multicast Displays the Multicast Group IP Address. Memberships: D-Link DIR-655 User Manual
  • D-Link DIR-655 | Product Manual - Page 73
    are deleted but logs of the latest events are retained. The Logs option support so you can send the log files to a computer on your network that address configured in the Tools > Email screen. Save Log: This option will save the router to a log file on your computer. D-Link DIR-655 User Manual 69
  • D-Link DIR-655 | Product Manual - Page 74
    Section 3 - Configuration Stats The screen below displays the Traffic Statistics. Here you can view the amount of packets that pass through the DIR-655 on both the Internet and the LAN ports. The traffic counter will reset if the device is rebooted. Active Sessions D-Link DIR-655 User Manual 70
  • D-Link DIR-655 | Product Manual - Page 75
    Section 3 - Configuration Wireless The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless clients. D-Link DIR-655 User Manual 71
  • D-Link DIR-655 | Product Manual - Page 76
    Section 3 - Configuration Support D-Link DIR-655 User Manual 72
  • D-Link DIR-655 | Product Manual - Page 77
    on your wireless router or access point. WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public key encryption system to ensure that only authorized network users can access the network. D-Link DIR-655 User Manual 73
  • D-Link DIR-655 | Product Manual - Page 78
    Section 4 - Security Wireless Security Setup Wizard To run the security wizard, click on Setup at the top and then click Launch Wireless Security Setup Wizard. Click Next to continue. D-Link DIR-655 User Manual 74
  • D-Link DIR-655 | Product Manual - Page 79
    Section 4 - Security The following screen will show you your Pre-Shared Key to enter on your wireless clients. Click Save to finish the Security Wizard. If you selected WPA-Enterprise, the RADIUS information will be displayed. Click Save to finish the Security Wizard. D-Link DIR-655 User Manual 75
  • D-Link DIR-655 | Product Manual - Page 80
    phrase must be between 8-63 characters. 6. Click Save Settings to save your settings. If you are configuring the router with a wireless adapter, you will lose connectivity until you enable WPA-PSK on your adapter and enter the same passphrase as you did on the router. D-Link DIR-655 User Manual 76
  • D-Link DIR-655 | Product Manual - Page 81
    the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Setup and then click Wireless Settings on the left side. 2. Next to Security Mode, select WPA-Enterprise. 3. Next to WPA Mode, select Auto, WPA2 Only, or WPA Only. Use Auto if you
  • D-Link DIR-655 | Product Manual - Page 82
    If the MAC Address Authentication box is selected then the user will need to connect from the same computer whenever logging into the wireless network. 10. Click Advanced to enter settings for a secondary RADIUS Server. 11. Click Apply Settings to save your settings. D-Link DIR-655 User Manual 78
  • D-Link DIR-655 | Product Manual - Page 83
    wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Click on the wireless icon in your system tray (lower-right corner). 2. The utility will display any available wireless networks in your area. D-Link DIR-655 User Manual
  • D-Link DIR-655 | Product Manual - Page 84
    you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. 4. The following window appears while your computer tries to connect to the router. D-Link DIR-655 User Manual 80
  • D-Link DIR-655 | Product Manual - Page 85
    or passphrase that is on your router and click Ok. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router. D-Link DIR-655 User Manual 81
  • D-Link DIR-655 | Product Manual - Page 86
    area. Click on a network (displayed using the SSID) and click the Connect button. If you get a good signal but cannot access the Internet, check you TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. D-Link DIR-655 User Manual 82
  • D-Link DIR-655 | Product Manual - Page 87
    used. 1. Open the Windows Vista® Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network. 2. Highlight the wireless network (SSID) you would like to connect to and click Connect. D-Link DIR-655 User Manual 83
  • D-Link DIR-655 | Product Manual - Page 88
    passphrase that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router. D-Link DIR-655 User Manual 84
  • D-Link DIR-655 | Product Manual - Page 89
    area. Click on a network (displayed using the SSID) and click the Connect button. If you get a good signal but cannot access the Internet, check you TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. D-Link DIR-655 User Manual 85
  • D-Link DIR-655 | Product Manual - Page 90
    Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. 2. Highlight the wireless network (SSID) you would like to connect to and click Connect. D-Link DIR-655 User Manual 86
  • D-Link DIR-655 | Product Manual - Page 91
    . Enter the WPA-PSK passphrase and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless router. D-Link DIR-655 User Manual 87
  • D-Link DIR-655 | Product Manual - Page 92
    . Software firewalls such as Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, and Windows XP firewall may block access to the configuration pages. Check the help files included with your firewall software for more information on disabling or configuring it. D-Link DIR-655 User Manual 88
  • D-Link DIR-655 | Product Manual - Page 93
    to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is admin and leave the password box empty. D-Link DIR-655 User Manual 89
  • D-Link DIR-655 | Product Manual - Page 94
    Section 6 - Troubleshooting 3. Why can't I connect to certain sites or send and receive emails when connecting through my router? If you are having a problem sending or receiving email, or syntax: ping [url] [-f] [-l] [MTU value] Example: ping yahoo.com -f -l 1472 D-Link DIR-655 User Manual 90
  • D-Link DIR-655 | Product Manual - Page 95
    below: • Open your browser, enter the IP address of your router (192.168.0.1) and click OK. • Enter your username (admin) and password (blank by default). Click OK to enter the web configuration page for the device. • Click on Setup and then click Manual Configure. • To change the MTU enter the
  • D-Link DIR-655 | Product Manual - Page 96
    network. Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network. D-Link DIR-655 User Manual
  • D-Link DIR-655 | Product Manual - Page 97
    house • Simple and easy to use Small Office and Home Office • Stay on top of everything at home as you would at office • Remotely access your office network from home • Share Internet connection and printer with multiple computers • No need to dedicate office space D-Link DIR-655 User Manual 93
  • D-Link DIR-655 | Product Manual - Page 98
    operate on same frequency. Security Don't let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA security feature on the router. Refer to product manual for detail information on how to set it up. D-Link DIR-655 User Manual 94
  • D-Link DIR-655 | Product Manual - Page 99
    an Access Point or wireless router. All the wireless devices, or clients, will connect to the wireless router or access point. An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc mode to communicate. D-Link DIR-655 User Manual
  • D-Link DIR-655 | Product Manual - Page 100
    . Some firewall software programs may block a DHCP request on newly installed adapters. If you are connecting to a wireless network at a hotspot (e.g. hotel, coffee shop, airport), please contact an employee or administrator to verify their wireless network settings. D-Link DIR-655 User Manual 96
  • D-Link DIR-655 | Product Manual - Page 101
    Gateway the same as the LAN IP address of your router (192.168.0.1). Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP. Step 5 Click OK twice to save your settings. D-Link DIR-655 User Manual 97
  • D-Link DIR-655 | Product Manual - Page 102
    throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely affect wireless signal range. D-Link DIR-655 User Manual 98
  • D-Link DIR-655 | Product Manual - Page 103
    of the router). You can find software updates and user documentation on the D-Link website as well as frequently asked questions and answers to technical issues. For customers within Canada: Phone Support: (800) 361-5265 Internet Support: http://support.dlink.ca D-Link DIR-655 User Manual 99
  • D-Link DIR-655 | Product Manual - Page 104
    the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware or part thereof that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund. D-Link DIR-655 User Manual 100
  • D-Link DIR-655 | Product Manual - Page 105
    the customer in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a Return Material Authorization ("RMA") number by completing the RMA form and entering the assigned Case ID Number at https:// rma.dlink.ca/. D-Link DIR-655 User Manual
  • D-Link DIR-655 | Product Manual - Page 106
    DLink Service Office. Improper or incorrectly performed maintenance or repair voids this Limited Warranty. Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED"AS-IS"WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER D-Link DIR-655 User Manual 102
  • D-Link DIR-655 | Product Manual - Page 107
    PERIOD SET Link Corporation/D-Link Canada, Inc., as stipulated by the United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice. Copyright ©2008-2010 by D-Link Corporation/D-Link Canada, Inc. All rights reserved. D-Link DIR-655 User Manual
  • D-Link DIR-655 | Product Manual - Page 108
    any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. D-Link DIR-655 User Manual 104
  • D-Link DIR-655 | Product Manual - Page 109
    This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the per regulations of Industry Canada. The required antenna impedance is 50 ohms. D-Link DIR-655 User Manual 105
  • D-Link DIR-655 | Product Manual - Page 110
    Appendix F - Registration Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 2.0 May 10, 2010 D-Link DIR-655 User Manual 106
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110