D-Link DSL-322T User Guide

D-Link DSL-322T Manual

Get D-Link DSL-322T PDF manuals and user guides View all D-Link DSL-322T manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DSL-322T manual content summary:

  • D-Link DSL-322T | User Guide - Page 1
    DSL-322T ADSL Modem User Guide October 2006 ESL322TEU.A1G
  • D-Link DSL-322T | User Guide - Page 2
    DSL-322T ADSL Modem User Guide Table Of Contents BEFORE YOU START ...IV Installation Overview...iv Setup Wizard ...iv Packing List...iv Installation Notes...v Installing the USB Driver ...viii INTRODUCTION ...1 Modem Description and Operation...1 Modem Features ...1 Front Panel Display ...2 Rear
  • D-Link DSL-322T | User Guide - Page 3
    Remote Log ...37 System ...38 Firmware...39 Test...40 STATUS ...41 Device Info...41 Log ...42 Statistics...43 ADSL ...44 HELP ...45 TECHNICAL SPECIFICATIONS 46 CONFIGURING IP SETTINGS ON YOUR COMPUTER 48 LOW PASS FILTERS FOR DSL 54
  • D-Link DSL-322T | User Guide - Page 4
    later in this manual after you have configured your computer's IP settings to connect to the Modem. Packing List Open the shipping carton and carefully remove all items. Make sure that you have the items listed here. • One DSL-322T ADSL Modem • One CD-ROM containing the User's Guide • One twisted
  • D-Link DSL-322T | User Guide - Page 5
    DSL-322T ADSL Modem User Guide Installation Notes In order to establish a connection to the Internet it will be necessary to provide information to the Modem that will be stored in its memory. For some users, only their account information (Username and Password) is required. For others, various
  • D-Link DSL-322T | User Guide - Page 6
    DSL-322T ADSL Modem User Guide Information you will need from your ADSL service provider: Username This is the Username used to log on to your ADSL service provider's network. It is commonly in the form − [email protected] Your ADSL service provider uses this to identify your account. Password
  • D-Link DSL-322T | User Guide - Page 7
    when you access the Modem's management interface. The default Password is admin. The user may change this. LAN IP addresses for the DSL-322T This is the IP address you will enter into the Address field of your web browser to access the Modem's configuration graphical user interface (GUI) using
  • D-Link DSL-322T | User Guide - Page 8
    -322T ADSL Modem User Guide Installing the USB Driver IMPORTANT: Do not connect the USB cable to your PC before completing the below steps. The CD-ROM shipped with the Modem contains the USB driver software. Insert the DSL-322T CD-ROM into the CD drive. Within a few seconds you should see a window
  • D-Link DSL-322T | User Guide - Page 9
    DSL-322T ADSL Modem User Guide 3. Click Install to begin the installation. 4. Click Finish to complete the InstallShield wizard. When the USB driver has been installed, insert one end of the USB cable included with the Modem into the DSL-322T Modem's USB port. Insert the other end of the USB cable
  • D-Link DSL-322T | User Guide - Page 10
    suitable for most small to medium sized offices. DSL-322T advantages include: • Data rates up to 24 Mbps for downstream and 1Mbps for upstream • Friendly web-based graphical user interface for configuration and management • Supports most ADSL, ADSL2, and ADSL2+ standards • Auto-handshake and rate
  • D-Link DSL-322T | User Guide - Page 11
    DSL-322T ADSL Modem User Guide Front Panel Display Place the Modem in a location that permits an easy view of the LED indicators on the front panel. The LED indicators on the front panel include Power, Status, ADSL, Ethernet, and USB. The ADSL, Ethernet, and USB indicators monitor link status and
  • D-Link DSL-322T | User Guide - Page 12
    DSL-322T ADSL Modem User Guide Rear Panel Connections All cable connections to the Modem are made at the rear panel. Connect the power adapter here to power on the Modem. Use the Reset button to restore the settings to the factory default values in the next chapter for instructions on using the
  • D-Link DSL-322T | User Guide - Page 13
    DSL-322T ADSL Modem User Guide 2 Hardware Installation The DSL-322T maintains three separate interfaces, an ADSL, an Ethernet, and a USB interface. Place the Modem in a location where it can be connected to the various devices as well as to a power source. The Modem should not be located where it
  • D-Link DSL-322T | User Guide - Page 14
    DSL-322T ADSL Modem User Guide Network Connections Wired network connections are provided through the ADSL port and the Ethernet port on the back of the Modem. See the Rear Panel diagram above and the illustrations below for examples. Connect ADSL Line Use the ADSL cable included with the Modem to
  • D-Link DSL-322T | User Guide - Page 15
    DSL-322T ADSL Modem User Guide 3 Basic Modem Configuration The first time you setup the Modem it is recommended that you configure the WAN connection using a single computer connected directly to the Modem. Once the WAN connection is functioning properly, you may continue to make changes to Modem
  • D-Link DSL-322T | User Guide - Page 16
    DSL-322T ADSL Modem User Guide Access the Configuration Manager In order to make sure your computer's IP settings allow it to communicate with the Modem, it is advisable to configure your system be a DHCP client - that is, it will get IP settings from the Modem. Appendix B describes how to
  • D-Link DSL-322T | User Guide - Page 17
    DSL-322T ADSL Modem User Guide Home When you successfully connect to the web manager, the Home directory tab will display the Setup Wizard window. You can launch the Setup Wizard from this page or use the buttons located in the left panel of the web page to view other windows used for basic
  • D-Link DSL-322T | User Guide - Page 18
    DSL-322T ADSL Modem User Guide The initial window summarizes the setup process. Click the Next button to proceed. You may stop using the Setup Wizard at any time by clicking the Exit button. If you exit the wizard you will return to the opening Setup Wizard window without saving any of the settings
  • D-Link DSL-322T | User Guide - Page 19
    DSL-322T ADSL Modem User Guide Using the Setup Wizard - Choose Connection Type Now select the Connection Type used for the Internet connection. Your ISP has given this information to you. The connection types available for "Multi-User" Mode are PPPoE/PPPoA, Static IP Address, and Bridge Mode. Each
  • D-Link DSL-322T | User Guide - Page 20
    DSL-322T ADSL Modem User Guide Using the Setup Wizard - For PPPoE/PPPoA connections: 1. Type in the Username and Password used to identify and Mux. 3. If you are instructed to change the VPI or VCI value, type in the correct setting in the available entry fields. Most users will not need to change
  • D-Link DSL-322T | User Guide - Page 21
    DSL-322T ADSL Modem User Guide Address. IPoA connection users who have not been given this information should leave the field blank. 3. If you are instructed to change the VPI or VCI value, type in the correct setting in the available entry fields. Most users will
  • D-Link DSL-322T | User Guide - Page 22
    DSL-322T ADSL Modem User Guide Using the Setup Wizard - For Bridge Mode connections: 1. Select the specific Connection Type from the drop-down menu. The available Bridge Mode connection and encapsulation types are 1483 Bridged IP LLC and 1483 Bridged IP VC-Mux. 2. If you are instructed to change the
  • D-Link DSL-322T | User Guide - Page 23
    DSL-322T ADSL Modem User Guide Using the Setup Wizard - Finish and Restart Finally you can confirm that the setup process is completed. If you are satisfied that you have entered all the necessary information correctly, click the Restart button to save the new configuration settings and restart the
  • D-Link DSL-322T | User Guide - Page 24
    DSL-322T ADSL Modem User Guide After the system is finished restarting, you will be returned to the opening page of the web manager. You may now continue to configure the Modem as desired. WAN To configure the Modem's basic configuration settings without running the Setup Wizard, you can access the
  • D-Link DSL-322T | User Guide - Page 25
    DSL-322T ADSL Modem User Guide WAN Settings window - PPPoE/PPPoA 16
  • D-Link DSL-322T | User Guide - Page 26
    DSL-322T ADSL Modem User Guide PPPoE/PPPoA Follow the instructions below to configure the Modem to use a PPPoE or PPPoA for the Internet connection. Make sure you have all the necessary information before you configure the WAN connection. To set up a PPPoE or PPPoA connection: 1. If not already
  • D-Link DSL-322T | User Guide - Page 27
    DSL-322T ADSL Modem User Guide 13. The Modem will save the new settings and restart. Upon restarting the Modem will automatically establish the WAN connection. The following provides additional description of the settings for PPPoA and PPPoE connections: PPPoA/PPPoE Parameters User Name Password
  • D-Link DSL-322T | User Guide - Page 28
    Static IP DSL-322T ADSL Modem User Guide non-TCP/IP port protocol link through the WAN interface. An IP Unnumbered interface does not have an IP address and therefore cannot be managed via Telnet or any other TCP/
  • D-Link DSL-322T | User Guide - Page 29
    DSL-322T ADSL Modem User Guide Static IP Address When the Modem is configured to use Static IP Address assignment for the WAN connection, you must manually assign a global IP Address, subnet mask, and gateway IP Address used for the WAN connection. Follow the instruction below to configure the Modem
  • D-Link DSL-322T | User Guide - Page 30
    DSL-322T ADSL Modem User Guide WAN Settings window- Static IP Address To configure a Static IP connection for the WAN, follow these steps: 1. Click the Static IP Address radio button in the WAN Settings section in the middle of the window. 21
  • D-Link DSL-322T | User Guide - Page 31
    DSL-322T ADSL Modem User Guide 2. The settings under ATM VC Setting at the top of the window should not be changed unless you have been instructed to change them. However, if you are instructed to change the VPI or VCI values, type in the values assigned for your account. Leave the Virtual Circuit
  • D-Link DSL-322T | User Guide - Page 32
    DSL-322T ADSL Modem User Guide Primary DNS Address Secondary DNS Address MTU most of the Internet. Get this IP address from your ISP. This is the IP address of the first choice for Domain Name Service (DNS) used to match the named URL web address used by most browsers with the actual global IP
  • D-Link DSL-322T | User Guide - Page 33
    Bridge Mode DSL-322T ADSL Modem User Guide WAN Settings window - Bridge Mode For Bridged connections it will be necessary for most users to install additional software on any computer that will the Modem for Internet access. The additional software is used for the purpose of identifying and
  • D-Link DSL-322T | User Guide - Page 34
    DSL-322T ADSL Modem User Guide 1. Click the Bridge Mode radio button in the WAN Settings section in the middle of the window. 2. The settings under ATM VC Setting at the top of the window should not be changed unless you have been instructed to change them. However, if you are instructed to change
  • D-Link DSL-322T | User Guide - Page 35
    DSL-322T ADSL Modem User Guide ATM Traffic Shaping The ATM settings section in the WAN Settings windows for the different connection types can be used to adjust QoS parameters for ADSL clients. This may not be available to all ADSL accounts. ATM Settings for WAN Connection Additional ATM settings
  • D-Link DSL-322T | User Guide - Page 36
    CDVT MBS DSL-322T ADSL Modem User Guide Cell Delay Variation Tolerance is a measure of the cell WAN Settings window The table below describes the ATM VC settings used to configure a PPPoE or PPPoA connection for an ADSL account. ATM VC Parameters Description PVC The Modem supports a single
  • D-Link DSL-322T | User Guide - Page 37
    DSL-322T ADSL Modem User Guide LAN You can configure the LAN IP address to suit your preference. Many users will find it convenient to use the default settings together with DHCP service to manage the IP settings for their private network. The IP address of the Modem is the base address used for
  • D-Link DSL-322T | User Guide - Page 38
    DSL-322T ADSL Modem User Guide DHCP The DHCP server is enabled by default for the Modem's Ethernet LAN interface. DHCP service will supply IP settings to workstations configured to automatically obtain IP settings that are connected to the Modem though the Ethernet port. When the Modem is used for
  • D-Link DSL-322T | User Guide - Page 39
    DSL-322T ADSL Modem User Guide The Ending IP manually configure IP settings on Windows workstations, open the TCP/IP Properties menu and select the "Use the following IP address" option. You will need to supply the IP address, subnet mask and default gateway (use the IP address of the DSL-322T
  • D-Link DSL-322T | User Guide - Page 40
    -322T ADSL Modem User Guide Save Settings and Reboot When you have configured the DSL-322T with the settings you desire, make sure you save those settings. To save the system configuration settings, click the Tools tab. You will be presented first with the Administrator Settings window. This window
  • D-Link DSL-322T | User Guide - Page 41
    DSL-322T ADSL Modem User Guide 4 Advanced Modem Management This chapter introduces and describes the management features that have not been presented in the previous chapter. These include the more advanced features used
  • D-Link DSL-322T | User Guide - Page 42
    DSL-322T ADSL Modem User Guide ADSL This window allows the user to set the configuration for ADSL protocols. For most ADSL accounts the default setting, ADSL2+ (Multi-mode), will work. This configuration works with all ADSL implementations. If you have been given instructions to change the
  • D-Link DSL-322T | User Guide - Page 43
    DSL-322T ADSL Modem User Guide ATM VCC This ATM Virtual Circuit connection window is used to configure the WAN connection. The window can be used as an alternative to configuring the same settings found on the WAN Settings windows in the Home directory. ATM VC Setting window To configure the PVC
  • D-Link DSL-322T | User Guide - Page 44
    DSL-322T ADSL Modem User Guide Tools Click the Tools tab to reveal the window buttons for various functions located in this directory. Administrator Settings is the first window that appears in the Tools directory. This window is used to change the system password used to access the web manager, to
  • D-Link DSL-322T | User Guide - Page 45
    DSL-322T ADSL Modem User Guide Time The Modem provides a number of options to maintain current date and time. Time window To configure system time on the Modem, select the method used to maintain time. The options available include using your computer's system clock (default) or setting the time and
  • D-Link DSL-322T | User Guide - Page 46
    DSL-322T ADSL Modem User Guide Remote Log Use this window to set up logging to servers or computers that are located outside the LAN or subnet of the Modem. Remote Log Settings window button when you have configured the log message receivers. Remember to save the settings to non-volatile memory. 37
  • D-Link DSL-322T | User Guide - Page 47
    DSL-322T ADSL Modem User Guide System Once you have configured the Modem to your satisfaction, it is a good idea to back up the configuration file to your computer. To save the current configuration settings to your computer, click the System button in the Tools directory to display the System
  • D-Link DSL-322T | User Guide - Page 48
    DSL-322T ADSL Modem User Guide Note Performing a Firmware Upgrade can sometimes change the configuration settings. Be sure to back-up the Modem's configuration settings before upgrading the firmware. Use this window to load the latest firmware for the device. Note that the device configuration
  • D-Link DSL-322T | User Guide - Page 49
    DSL-322T ADSL Modem User Guide Test This window is used to test connectivity of the Modem. A Ping test may be done through the local or external tests of your system software and hardware connections. Use this window when working with your ISP to troubleshoot problems. Diagnostic Test window 40
  • D-Link DSL-322T | User Guide - Page 50
    DSL-322T ADSL Modem User Guide Status Use the various read-only windows to view system information and monitor performance. Device Info Use this window to quickly view basic current information about the LAN and WAN interfaces and device information including Firmware Version and MAC address. Device
  • D-Link DSL-322T | User Guide - Page 51
    -322T ADSL Modem User Guide Log The system log displays chronological event log data. Use the navigation buttons to view or scroll log pages. You may also save a simple text file containing the log to your computer. Click the Save Log button and follow the prompts to save the file. View Log window
  • D-Link DSL-322T | User Guide - Page 52
    DSL-322T ADSL Modem User Guide Statistics Use this window to monitor traffic on the Ethernet, ADSL, or USB Internet connection. Select the interface for which you want to view packet statistics and the information will appear below. Traffic Statistics window Click Refresh to view traffic information
  • D-Link DSL-322T | User Guide - Page 53
    DSL-322T ADSL Modem User Guide ADSL Use this window and the Diagnostic Test window (Tools > Test) for troubleshooting the ADSL connection. ADSL Status window 44
  • D-Link DSL-322T | User Guide - Page 54
    Help DSL-322T ADSL Modem User Guide Click the desired hyperlink to access helpfiles. Help window 45
  • D-Link DSL-322T | User Guide - Page 55
    DSL-322T ADSL Modem User Guide A Technical Specifications General Standards: Protocols: Data Transfer Rate: Media Interface: ADSL Standards ADSL2 Standards • ANSI T1.413 Issue 2 • ITU G.992.3 (G.dmt.bis) Annex A • ITU G.992.1 (G.dmt) AnnexA • ITU G.992.4 (G.lite.bis) Annex A • ITU G.992.2
  • D-Link DSL-322T | User Guide - Page 56
    DSL-322T ADSL Modem User Guide Physical and Environmental DC Inputs: Power Adapter: Input: 120V AC 60Hz Output: 7.5V DC, 1.5A Power Consumption: 11.25 Watts (max) Operating Temperature: 0° to 40°C
  • D-Link DSL-322T | User Guide - Page 57
    DSL-322T ADSL Modem User Guide B Configuring IP Settings on Your Computer In order to configure your system to receive IP settings from the Modem it must first have the TCP/IP protocol installed. If you have an Ethernet port on your computer, it probably already has TCP/IP protocol
  • D-Link DSL-322T | User Guide - Page 58
    DSL-322T ADSL Modem User Guide 2. In the Control Panel window, click Network and Internet Connections. Click Network and Internet Connections. 3. In the Network and Internet Connections window, click Network Connections. Click Network Connections. 4. In the Network Connections window, right-click on
  • D-Link DSL-322T | User Guide - Page 59
    DSL-322T ADSL Modem User Guide 5. In the General tab of the Local Area Connection Properties window, highlight Internet Protocol (TCP/IP) under "This connection uses the following items:" by clicking on it once. Click on the Properties button. Click Properties. 6. Select "
  • D-Link DSL-322T | User Guide - Page 60
    DSL-322T ADSL Modem User Guide Windows 2000 First, check for the IP protocol and, if necessary, install it: 1. In the Windows task bar, click the Start button, point to Settings, and then click Control Panel. 2. Double-click the Network and Dial-up Connections icon. 3. In the
  • D-Link DSL-322T | User Guide - Page 61
    DSL-322T ADSL Modem User Guide Windows 95 and Windows 98 First, check for the IP protocol and, if necessary, install it: 1. In the Windows task bar, click the Start button, point to Settings, and then click Control Panel. Double-click the Network icon. 2. The Network dialog box displays with a
  • D-Link DSL-322T | User Guide - Page 62
    DSL-322T ADSL Modem User Guide Your computer is now ready to use the Modem's DHCP server. Windows NT 4.0 Workstations First, check for the IP protocol and, if necessary, install it: 1. In the Windows NT task bar, click the Start button, point to Settings, and then click Control Panel. 2. In the
  • D-Link DSL-322T | User Guide - Page 63
    DSL-322T ADSL Modem User Guide C Low Pass Filters for DSL Most ADSL clients will be required to install a simple device that prevents the ADSL line from interfering with regular telephone services. These devices are commonly referred to as microfilters or low pass filters. The two basic styles of
  • D-Link DSL-322T | User Guide - Page 64
    DSL-322T ADSL Modem User Guide Three Port Filter Another style of filter is installed at the same point where the Modem connects to the telephone line. Only a single filter is required. The connection ports are typically labeled as follows: • Line - This port connects to the wall jack. • ADSL - This
  • D-Link DSL-322T | User Guide - Page 65
    Synergy Singapore 609917 TEL: 65-6774-6233 FAX: 65-6774-6322 URL: www.dlink-intl.com Australia 1 Giffnock Avenue North Ryde, NSW 2113 Australia TEL: 61-2-8899-1800 FAX: 61-2-8899-1868 URL: www.dlink.com.au India D-Link House, Kurla Bandra Complex Road Off CST Road, Santacruz (East) Mumbai - 400098
  • D-Link DSL-322T | User Guide - Page 66
    DSL-322T ADSL Modem User Guide 57
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
DSL-322T
ADSL Modem
User Guide
October 2006
ESL322TEU.A1G