D-Link DSL-502G User Guide
D-Link DSL-502G Manual
 |
View all D-Link DSL-502G manuals
Add to My Manuals
Save this manual to your list of manuals |
D-Link DSL-502G manual content summary:
- D-Link DSL-502G | User Guide - Page 1
DSL-502T ADSL Router User 's Guide (December 2004) 651SL502T045 - D-Link DSL-502G | User Guide - Page 2
DSL-502T ADSL Router User's Guide FCC Warning This equipment has been tested and found to comply with radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause harmful interference to radio communications. Operation of this equipment in a - D-Link DSL-502G | User Guide - Page 3
Table Of Contents About This User's Guide v BEFORE YOU START V Installation Overview v The Setup Wizard v PACKING LIST V INSTALLATION REQUIREMENTS VI Installing the USB Driver ix INTRODUCTION 1 Router Description and Operation 1 Standards Compatibility and Compliance 3 Front Panel Display - D-Link DSL-502G | User Guide - Page 4
Load Configuration File 44 Restore Factory Default Settings 44 Time...45 Firmware Upgrade 46 Test...47 Save Settings and Reboot 48 Router Status Information 49 Device Information Display 49 DHCP Clients 50 Log...50 Traffic ...51 ADSL ...51 TECHNICAL SPECIFICATIONS 52 IP ADDRESS SETUP 54 IP - D-Link DSL-502G | User Guide - Page 5
the USB driver. Follow the installation instructions below to install the USB driver. Packing List Open the shipping carton and carefully remove all items. Make sure that you have the items listed here. 1. One DSL-502T ADSL Ethernet Router 2. One CD-ROM containing the User's Guide, USB driver and - D-Link DSL-502G | User Guide - Page 6
DSL-502T ADSL Router User's Guide Installation Requirements In order to establish a connection to the Internet it will be necessary to provide information to the Router that will be stored in its memory. For some users, only their account information (Username and Password) is required. For others, - D-Link DSL-502G | User Guide - Page 7
DSL-502T ADSL Router User's Guide Information you will need from your ADSL service provider: Username This is the Username used to log on to your ADSL service provider's network. It is commonly in the form − [email protected]. Your ADSL service provider uses this to identify your account. Password - D-Link DSL-502G | User Guide - Page 8
. The default Password is admin. The user may change this. LAN IP addresses for the DSL-502T This is the IP address you will enter into the Address field of your web browser to access the Router's configuration graphical user interface (GUI) using a web browser. The default IP address is 10 - D-Link DSL-502G | User Guide - Page 9
it to launch the installation software. The auto-run USB driver setup must be completed before connecting the router to your PC with the USB cable. To install the driver follow these instructions: 1. Click the Install DSL-502T link to launch the USB driver installation software. 2. Click Next on the - D-Link DSL-502G | User Guide - Page 10
DSL-502T ADSL Router User's Guide 3. Click Install to begin the installation. 4. Click Finish to complete the InstallShield wizard. When the USB driver has been installed, insert one end of the USB cable included with the router into the DSL-502T router's USB port. Insert the other end of the USB - D-Link DSL-502G | User Guide - Page 11
and bandwidth hungry applications for business and residential customers. ADSL routers and modems provide faster downloads and more reliable connectivity to the user without loss of quality or disruption of voice/fax telephone capabilities. ADSL service operates at speeds of up to 8 Mbps downstream - D-Link DSL-502G | User Guide - Page 12
User's Guide Router Features The DSL-502T ADSL Router utilizes the latest ADSL enhancements to provide a reliable Internet portal suitable for most small to medium sized offices. DSL-502T advantages include: • PPP (Point-to-Point Protocol) Security - The DSL-502T ADSL Router supports PAP (Password - D-Link DSL-502G | User Guide - Page 13
DSL-502T ADSL Router User's Guide Standards Compatibility and Compliance The DSL-502T complies with or is compatible with the Supports RFC 2131 and RFC 2132 DHCP functions including: automatic assignment of IP address, use of subnet mask and default gateway and provision of DNS server address - D-Link DSL-502G | User Guide - Page 14
DSL-502T ADSL Router User's Guide Front Panel Display Place the Router in a location that permits an easy view of the LED indicators on the front panel. The LED indicators on the front panel include the Power, Status, ADSL Link/Act, Ethernet Link/Act, and USB Link/Act indicators. The ADSL, Ethernet, - D-Link DSL-502G | User Guide - Page 15
DSL-502T ADSL Router User's Guide Rear Panel All cable connections to the Router are made at the rear panel. The factory-reset button is located here as well. USB port, connect USB cable here and install USB driver ADSL port, connect ADSL cable here Ethernet port, connect Ethernet cable here - D-Link DSL-502G | User Guide - Page 16
to the factory default IP address 10.1.1.1 and the subnet mask is 255.0.0.0, the default management Username is admin and the default Password is admin. Network Connections Network connections are provided through the ADSL port, the Ethernet port and the USB port on the back of the Router. See the - D-Link DSL-502G | User Guide - Page 17
DSL-502T ADSL Router User's Guide represents the WAN interface, the connection to the Internet. It is the physical link to the service provider's network backbone and ultimately to the Internet. Connect Router to Ethernet The Router may be connected to a single computer or Ethernet device through - D-Link DSL-502G | User Guide - Page 18
DSL-502T ADSL Router User's Guide 3 Basic Router Configuration The first time you setup the Router it is recommended that you configure the WAN connection using a single computer making sure that both the computer and the Router are not connected to the LAN. Once the WAN connection is functioning - D-Link DSL-502G | User Guide - Page 19
DSL-502T ADSL Router User's Guide Configure Windows XP for DHCP Use the following steps to configure a computer running Windows XP to be a DHCP client. 1. From the Start menu on your desktop, go to Settings, then click on Network Connections. 9 - D-Link DSL-502G | User Guide - Page 20
DSL-502T ADSL Router User's Guide In the Network Connections window, right-click on LAN (Local Area Connection), then click Properties. 2. In the General tab of the Local Area Connection Properties menu, highlight Internet Protocol (TCP/IP) under "This connection uses the following items:" by - D-Link DSL-502G | User Guide - Page 21
DSL-502T ADSL Router User's Guide 3. Select "Obtain an IP address automatically" by clicking once in the circle. Click the OK button. Your computer is now ready to use the Router's DHCP server. Windows 2000 First, check for the IP protocol and, if necessary, install it: 1. In the Windows task bar, - D-Link DSL-502G | User Guide - Page 22
DSL-502T ADSL Router User's Guide Your computer is now ready to use the Router's DHCP server. Windows ME First, check for the IP protocol and, if necessary, install it: 1. In the Windows task bar, click the Start button, point to Settings, and then click Control Panel. 2. Double-click - D-Link DSL-502G | User Guide - Page 23
DSL-502T ADSL Router User's Guide Configure Windows 95 and Windows 98 for DHCP 1. Open the Control Panel window, and then click the Network icon. 2. Select the network component labeled TCP/IP, and then click Properties. 3. If you have multiple TCP/IP listings, select the listing associated with - D-Link DSL-502G | User Guide - Page 24
DSL-502T ADSL Router User's Guide Access the Configuration Manager Now that your computer's IP settings allow it to communicate with the Router, you can access the configuration software. Be sure that the web browser on your computer is not configured to use a proxy server in the Internet - D-Link DSL-502G | User Guide - Page 25
DSL-502T ADSL Router User's Guide Configure the Router When you successfully connect to the web manager, the Home directory tab will display the Setup Wizard menu. You can launch the Setup Wizard from this page or use the menu buttons located in the left panel of the web page to view other menus - D-Link DSL-502G | User Guide - Page 26
DSL-502T ADSL Router User's Guide Tools Status Help Click the Tools tab to access the Administrator Settings (used to set the system user name and password, backup and load settings), System Time Configuration, Firmware Upgrade, Diagnostic Test and Save & Reboot menus. Click the Status tab to view - D-Link DSL-502G | User Guide - Page 27
DSL-502T ADSL Router User's Guide Note The default User Name admin used for Router management cannot be changed. Set the system time of the Router. Choose the time zone you are in from the pull-down menu and click Next. If you wish to return to the previous menu during the setup process, click - D-Link DSL-502G | User Guide - Page 28
DSL-502T ADSL Router User's Guide menu are PPPoE LLC, PPPoA LLC and PPPoA VC-MUX. For Bridge Mode and Static IP connections, use the WAN menu in the Home directory to configure the connection (see below for instruction on setting up Bridge and Static IP connections). 1. Select the Connection Type - D-Link DSL-502G | User Guide - Page 29
DSL-502T ADSL Router User's Guide Finally you can confirm that the setup process is completed. If you are satisfied that you have entered all the necessary information correctly, click the Restart button to save the new configuration settings and restart the Router. If you need to change settings - D-Link DSL-502G | User Guide - Page 30
DSL-502T ADSL Router User's Guide Configure WAN Connection To configure the Router's basic configuration settings without running the Setup Wizard, you can access the menus used to configure WAN, LAN, DHCP and DNS settings directly from the Home directory. To access the WAN Settings menu, click on - D-Link DSL-502G | User Guide - Page 31
DSL-502T ADSL Router User's Guide PPPoE and PPPoA Connection for WAN Follow the instructions below to configure the Router to use a PPPoE or PPPoA for the Internet connection. Make sure you have all the necessary information before you configure the WAN connection. 1. Click to select the PPPoE/PPPoA - D-Link DSL-502G | User Guide - Page 32
DSL-502T ADSL Router User's Guide Bridged Connection for WAN For Bridged connections it will be necessary for most users to install additional software on any computer that will the Router for Internet access. The additional software is used for the purpose of identifying and verifying your - D-Link DSL-502G | User Guide - Page 33
DSL-502T ADSL Router User's Guide Static IP Address for WAN When the Router is configured to use Static IP Address assignment for the WAN connection, you must manually assign a global IP Address, Subnet Mask and Gateway IP Address used for the WAN connection. Most users will also to - D-Link DSL-502G | User Guide - Page 34
DSL-502T ADSL Router User's Guide Multiple Private Virtual Connections The Router supports multiple virtual connections. Up to eight PVCs to eight separate destinations can be created and operated simultaneously utilizing the same bandwidth. Additional PVC connections can - D-Link DSL-502G | User Guide - Page 35
DSL-502T ADSL Router User's Guide In the example below, a new VC (Pvc1) has been added using the WAN Settings menu. The connection is setup as a bridged connection. Configure new VC The new VC appears can be configured separately in other menus such as Static Routing. 25 - D-Link DSL-502G | User Guide - Page 36
DSL-502T ADSL Router User's Guide LAN IP Settings You can configure the LAN IP address to suit your preference. Many users will find it convenient to use the default settings together with DHCP service to manage the IP settings for their private network. The IP address of the Router is the base - D-Link DSL-502G | User Guide - Page 37
-502T ADSL Router User's Guide DHCP Server Settings for the LAN The DHCP server is enabled by default for the Router's Ethernet LAN interface. DHCP service will supply IP settings to workstations configured to automatically obtain IP settings that are connected to the Router though the Ethernet port - D-Link DSL-502G | User Guide - Page 38
DSL-502T ADSL Router User's Guide DHCP Relay To use DHCP service from your ISP, select the DHCP Relay option and type the DHCP Relay IP address in the space provided. Click Apply to begin DHCP relay from the ISP. Note To use DHCP Relay from the ISP, DHCP Service Filtering must be disabled. See - D-Link DSL-502G | User Guide - Page 39
DSL-502T ADSL Router User's Guide Save Settings and Reboot When you have configured the DSL-502T with the settings you desire, make sure you save those settings. To save the system configuration settings, click the Tools tab. You will be presented first with the Administrator Settings menu. This - D-Link DSL-502G | User Guide - Page 40
, Port Forwarding, DMZ, IP/MAC Filters, Firewall, NAT, ATM, Static Routing, Dynamic Routing (RIP) and Remote Access menus. Click the Tools tab to access the Administrator Settings (used to set the system user name and password, backup and load settings), System Time Configuration, Firmware Upgrade - D-Link DSL-502G | User Guide - Page 41
DSL-502T ADSL Router User's Guide UPnP UPnP supports zero-configuration networking and automatic discovery for many types of networked devices. When enabled, it allows other devices that support UPnP to dynamically join a network, obtain an IP address, convey its capabilities, and learn about the - D-Link DSL-502G | User Guide - Page 42
DSL-502T ADSL Router User's Guide Port Forwarding Use the Port Forwarding menu to create Virtual Server functions through the Router. A Virtual Server can allow remote users to access services on your LAN such as FTP for file transfers or SMTP and POP3 for e-mail. The DSL-502T will accept remote - D-Link DSL-502G | User Guide - Page 43
DSL-502T ADSL Router User's Guide To configure a virtual server set, define the following settings in the Virtual Server configuration menu located in the top half of the browser window. Parameter Description Rule Name Provide a name for the rule. This name will not appear in - D-Link DSL-502G | User Guide - Page 44
DSL-502T ADSL Router User's Guide DMZ Since some applications are not compatible with NAT, the Router supports use of a DMZ IP address for a single host on the LAN. This IP address through the DMZ. DMZ IP address configuration To designate a DMZ IP address, type in the IP Address of the server or - D-Link DSL-502G | User Guide - Page 45
DSL-502T ADSL Router User's Guide Filters Filter rules in the Router are put in place to allow or block specified traffic. The Filter Rules however can be used in a single direction to examine and then Allow - D-Link DSL-502G | User Guide - Page 46
DSL-502T ADSL Router User's Guide The parameters described below are used to set up filter rules. Parameter Description Source IP For an Outbound Filter, this is the IP address or IP addresses on your LAN for which you are creating the filter rule. For an Inbound Filter, this is the IP address - D-Link DSL-502G | User Guide - Page 47
DSL-502T ADSL Router User's Guide Firewall The Firewall Configuration menu allows the Router to enforce specific predefined policies intended to protect against certain common types of attacks. There are two general types of protection (DoS, Port Scan) that can be enabled on the Router, as well as - D-Link DSL-502G | User Guide - Page 48
DSL-502T ADSL Router User's Guide A DoS "denial-of-service" attack is characterized by an explicit attempt by attackers to prevent legitimate users of a service from using that service. Examples include: attempts to "flood" a network, thereby preventing legitimate network traffic, attempts to - D-Link DSL-502G | User Guide - Page 49
DSL-502T ADSL Router User's Guide ATM The ATM Virtual Circuit connection menu is used to configure the WAN connection. If you are using multiple PVCs, you can change the configuration of any PVC in this menu. To create new or additional PVCs, read the section below on Multiple PVCs. This menu can be - D-Link DSL-502G | User Guide - Page 50
DSL-502T ADSL Router User's Guide Static Routing Use Static Routing route to a specific destination IP on the local network, enter a Destination IP address, Netmask, then click the Gateway radio button and type in the Gateway's IP address. Click Apply . Remember to save the configuration changes. 40 - D-Link DSL-502G | User Guide - Page 51
DSL-502T ADSL Router User's Guide Dynamic Routing (RIP) The Router supports RIP v1 and RIP v2 used to share and RIP v2. The direction configuration refers to the RIP request. Select In to allow RIP requests from other devices. Select Out to instruct the Router to make RIP requests for routing - D-Link DSL-502G | User Guide - Page 52
DSL-502T ADSL Router User's Guide Remote Access Use the Remote Access menu in the Advanced directory to enable remote management of the Router through the web interface or via Telnet from a specified source IP address. This will enable Router and network managment from outside the local network - D-Link DSL-502G | User Guide - Page 53
DSL-502T ADSL Router User's Guide Tools and Utilities Click the Tools tab to reveal the menu buttons for various functions located in this directory. The Administrator Settings is the first menu that appears in the Tools directory. It is used to change the system password used to access the web - D-Link DSL-502G | User Guide - Page 54
DSL-502T ADSL Router User's Guide Save or Load Configuration File Once you have configured the Router to your satisfaction, it is a good idea to back up the configuration file to your computer. To save the current configuration settings to your computer, click the Admin button in the Tools directory - D-Link DSL-502G | User Guide - Page 55
DSL-502T ADSL Router User's Guide Time The Router provides a number of options to maintain current date and time including SNTP. Time Configuration To configure system time on the Router, select the method used to maintain time. The options available include SNTP, using your computer's system clock - D-Link DSL-502G | User Guide - Page 56
DSL-502T ADSL Router User's Guide Firmware Upgrade Note Performing a Firmware Upgrade can sometimes change the configuration settings. Be sure to back-up the Router's configuration settings before upgrading the firmware. Use the Firmware Upgrade menu to load the latest firmware for the device. - D-Link DSL-502G | User Guide - Page 57
DSL-502T ADSL Router User's Guide Test The Test menus are used to test connectivity of the Router. A Ping test may be done through the local or external interface to test connectivity to known IP addresses to troubleshoot problems. Ping and Diagnostics Test Menu Ping Test Type the IP address you - D-Link DSL-502G | User Guide - Page 58
DSL-502T ADSL Router User's Guide Save Settings and Reboot When you have configured the DSL-502T with the settings you desire, make sure you save those settings. To save the system configuration settings, click the Tools tab. You will be presented first with the Administrator Settings menu. This - D-Link DSL-502G | User Guide - Page 59
DSL-502T ADSL Router User's Guide Router Status Information Use the various read-only menus to view system information and monitor performance. Device Information Display Use the Device Information window to quickly - D-Link DSL-502G | User Guide - Page 60
DSL-502T ADSL Router User's Guide DHCP Clients View all current DHCP clients connected to the DSL-502T. DHCP Clients list Log The system log displays chronological event log data. Use the navigation buttons to view or scroll log pages. You may also - D-Link DSL-502G | User Guide - Page 61
DSL-502T ADSL Router User's Guide Traffic See the Traffic Statistics window to monitor traffic on the Ethernet, USB or ADSL Internet connection. Traffic Statistics information ADSL Use the ADSL Status information and the Test page for troubleshooting the ADSL connection. ADSL Status information - D-Link DSL-502G | User Guide - Page 62
DSL-502T ADSL Router User's Guide A Technical Specifications Standards: General ITU G.992.1 (G.dmt) ITU G.992.2 (G.lite) ITU G.994.1 (G.Hs) ITU-T Rec. I.361 ITU-T Rec. I.610 IEEE 802.3 IEEE 802.3u IEEE 802.1d RFC 791 (IP Routing) RFC 792 (UDP) RFC 826 (ARP) RFC 1058 (RIP 1) RFC 1389 (RIP 2) RFC - D-Link DSL-502G | User Guide - Page 63
DSL-502T ADSL Router User's Guide DC Inputs: Power Adapter: Power Consumption: Operating Temperature: Humidity: Dimensions: Weight: EMI: Safety: Reliability: Physical and Environmental Input: 100V ~ 240V AC 50 ~ 60Hz Output: 9V - D-Link DSL-502G | User Guide - Page 64
DSL-502T ADSL Router User's Guide B IP Address Setup The DSL-502T is designed to provide network administrators maximum flexibility for IP addressing on the Ethernet LAN. The easiest IP setup choice in most cases is to let the Router do it using DHCP, which is enabled by default. This appendix - D-Link DSL-502G | User Guide - Page 65
DSL-502T ADSL Router User's Guide network), while the last three numbers denote the host IP address (each computer must have a unique address to distinguish it on the network). The IP address scheme used in Example #1 can be used for any LAN that requires up to 253 separate IP addresses (excluding - D-Link DSL-502G | User Guide - Page 66
DSL-502T ADSL Router User's Guide C IP Concepts This appendix describes some basic IP concepts, the TCP/IP addressing scheme and shows how to assign IP Addresses. When setting up the Router, you must make sure it has a valid IP address. Even if you will not use the WAN port (ADSL port), you should - D-Link DSL-502G | User Guide - Page 67
DSL-502T ADSL Router User's Guide Networks attached to the Internet are assigned class types that determine the maximum number of possible hosts per network. The previous figure illustrates how the net and host portions of the IP address differ among the three classes. Class A is assigned to - D-Link DSL-502G | User Guide - Page 68
DSL-502T ADSL Router User's Guide It is recommended that you choose private network IP Addresses from the above list. For more information on address assignment, refer to RFC 1597, Address Allocation for Private Internets and RFC 1466, Guidelines for Management of IP Address Space. Subnet Mask In - D-Link DSL-502G | User Guide - Page 69
DSL-502T ADSL Router User's Guide D Microfilters and Splitters Most ADSL clients will be required to install a simple device that prevents the ADSL line from interfering with regular telephone services. These devices are commonly referred to as microfilters or sometimes called (inaccurately) line - D-Link DSL-502G | User Guide - Page 70
DSL-502T ADSL Router User's Guide Line Splitter If you are instructed to use a "line splitter", you must install the device between the Router and the phone jack. Use standard telephone cable with standard RJ-11 connectors. The splitter has three RJ-11 ports used to connect to the wall jack, the - D-Link DSL-502G | User Guide - Page 71
North Ryde, NSW 2113, Sydney, Australia TEL: 61-2-8899-1800 FAX: 61-2-8899-1868 TOLL FREE (Australia): 1800-177100 URL: www.dlink.com.au E-MAIL: [email protected] D-Link Brasil Ltda. Edificio Manoel Tabacow Hydal, Rua Tavares Cabral 102 Sala 31, 05423-030 Pinheiros, Sao Paulo, Brasil TEL: (55 11 - D-Link DSL-502G | User Guide - Page 72
098 India TEL: 91-022-652-6696/6578/6623 FAX: 91-022-652-8914/8476 URL: www.dlink-india.com & www.dlink.co.in E-MAIL: [email protected] & [email protected] Italy D-Link Mediterraneo Srl/D-Link Italia Via Nino Bonnet n. 6/B, 20154, Milano, Italy TEL: 39-02-2900-0676 FAX: 39-02-2900-1723 - D-Link DSL-502G | User Guide - Page 73
dlink.se E-MAIL: [email protected] D-Link Taiwan 2F, No. 119 Pao-chung Road, Hsin-tien, Taipei, Taiwan TEL: 886-2-2910-2626 FAX: 886-2-2910-1515 URL: www.dlinktw.com.tw E-MAIL: [email protected] D-Link dlink-me.com D-Link dlink-me.com D-Link dlink.co.uk E-MAIL: [email protected] D-Link
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
 |
 |
DSL-502T
ADSL Router
User ‘s Guide
(December 2004)
651SL502T045