D-Link DWL-3200AP Product Manual - Page 101

Ethernet LED - connection problem

Get D-Link DWL-3200AP - AirPremier - Wireless Access Point PDF manuals and user guides
UPC - 790069273544
View all D-Link DWL-3200AP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

DWL-3200AP User's Manual Troubleshooting Troubleshooting This Chapter provides solutions to problems that can occur during the installation and operation of the DWL-3200AP Managed Wireless Access Point. We cover various aspects of the network setup, including the network adapters. Please read the following if you are having problems. Note: It is recommended that you use an Ethernet connection to configure the DWL-3200AP . 1. The computer used to configure the DWL-3200AP cannot access the Configuration menu.  Check that the Ethernet LED on the DWL-3200AP is ON. If the LED is not ON, check that the cable for the Ethernet connection is securely inserted.  Check that the Ethernet Adapter is working properly. Please see item 3 (Check that the drivers for the network adapters are installed properly) in this Troubleshooting section to check that the drivers are loaded properly.  Check that the IP address is in the same range and subnet as the DWL-3200AP. Please see Checking the IP Address in Windows® XP in the Networking Basics section of this manual. Note: The IP address of the DWL-3200AP is 192.168.0.50. All the computers on the network must have a unique IP address in the same range, e.g., 192.168.0.x. Any computers that have identical IP addresses will not be visible on the network. They must all have the same subnet mask, e.g., 255.255.255.0.  Do a Ping test to make sure that the DWL-3200AP is responding. Go to Start>Run>Type Command>Type ping 192.168.0.50. A successful ping will show four replies. Note: If you have changed the default IP address, make sure to ping the correct IP address assigned to the DWL-3200AP. D-Link Systems, Inc. 101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
101
DWL-3200AP User’s Manual
D-Link Systems, Inc.
Troubleshooting
Troubleshooting
This Chapter provides solutions to problems that can occur during the installation and
operation of the DWL-3200AP Managed Wireless Access Point. We cover various
aspects of the network setup, including the network adapters. Please read the following
if you are having problems.
Note:
It is recommended that you use an Ethernet connection to
configure the
DWL-3200AP .
1. The computer used to configure the DWL-3200AP cannot access the
Configuration menu.
Check that the
Ethernet LED
on the DWL-3200AP is
ON
. If the
LED
is not
ON
,
check that the cable for the Ethernet connection is securely inserted.
Check that the Ethernet Adapter is working properly.
Please see item 3
(
Check
that the drivers for the network adapters are installed properly
) in this
Troubleshooting
section to check that the drivers are loaded properly.
Check that the
IP address
is in the same range and subnet as the DWL-3200AP.
Please see
Checking the IP Address
in Windows
®
XP
in the
Networking Basics
section of this manual.
Note:
The IP address of the DWL-3200AP is 192.168.0.50. All the computers on the
network must have a unique IP address in the same range, e.g., 192.168.0.x. Any
computers that have identical IP addresses will not be visible on the network. They
must all have the same subnet mask, e.g., 255.255.255.0.
Do a
Ping test
to make sure that the DWL-3200AP is responding. Go to
Start
>
Run
>Type
Command
>Type
ping 192.168.0.50.
A successful ping will show
four replies.
Note: If you have changed the default IP address, make sure to ping the correct IP
address assigned to the DWL-3200AP.