DIRECTV RC64 User Manual - Page 11

Verifying the Codes, Changing Volume Lock, Locking Volume to AV1, AV2 or TV - remote control codes

Get DIRECTV RC64 PDF manuals and user guides View all DIRECTV RC64 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

7. Use the CHANT key to step back a code. 8. When the TV or component turns off turns off or performs the action you selected in step 5, stop pressing the CHANS key. Then, press and release the SELECT key. NOTE: If the light flashes 3 times before the TV or component responds, you've cycled through all codes and the code you need is not available. You must use the remote that came with your TV or component. Verifying the Codes Once you have set up the DIRECTV® Universal Remote Control using the above steps, use the following instructions to find out the 5-digit code to which your component responded: 1. Slide the MODE switch to the appropriate position. 2. Press and hold the MUTE and SELECT keys at the same time until the green light under the selected switch position flashes twice, then release both keys. 3. Enter 9-9-0. (The green light under the selected switch position flashes twice.) 4. To view the first digit in the code, Press and release then number 1 key. Wait three seconds, and count the number of times the green light flashes. Write this number down in the leftmost TV, AV1 or AV2 code box found on page 10. 5. Repeat step 4 four more times for the remaining digits; i.e., press number 2 for the second digit, 3 for the third digit, 4 for the fourth digit and 5 for the final digit. CHANGING VOLUME LOCK Depending on how you set up your remote, the VOL and MUTE may control the volume only on your TV, regardless of the position of the MODE switch. This remote can be set up so that the VOL and MUTE keys work only with the component selected by the MODE switch. To enable this feature, perform the following steps: 1. Press and hold the MUTE and SELECT keys until the green light under the DIRECTV position flashes twice, then release both keys. 2. Using the number keys, enter 9-9-3. (The green light will flash twice after the 3.) 3. Press and release the VOL+ key. (The green light flashes 4 times.) Now the VOL and MUTE keys will work only for the component selected by the MODE switch position. Locking Volume to AV1, AV2 or TV 1. Slide the MODE switch to the AV1, AV2 or TV position to lock the volume. 2. Press and hold the MUTE and SELECT keys until the green light under the selected switch flashes twice and release both keys. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
11
7.
Use the
CHAN
key to step back a code.
8.
When the TV or component turns off turns off or
performs the action you selected in step 5, stop
pressing the
CHAN
key. Then, press and release the
SELECT
key.
NOTE:
If the light flashes 3 times before the TV or com-
ponent responds, you've cycled through all
codes and the code you need is not available. You
must use the remote that came with your TV or
component.
Verifying the Codes
Once you have set up the DIRECTV
®
Universal Remote
Control using the above steps, use the following
instructions to find out the 5-digit code to which your
component responded:
1.
Slide the
MODE
switch to the appropriate position.
2.
Press and hold the
MUTE
and
SELECT
keys at the same
time until the green light under the selected switch
position flashes twice, then release both keys.
3.
Enter
9-9-0
. (The green light under the selected
switch position flashes twice.)
4.
To view the first digit in the code, Press and release
then number
1
key. Wait three seconds, and count the
number of times the green light flashes. Write this
number down in the leftmost TV, AV1 or AV2 code
box found on page 10.
5.
Repeat step 4 four more times for the remaining
digits; i.e., press number
2
for the second digit,
3
for
the third digit,
4
for the fourth digit and
5
for the final
digit.
CHANGING VOLUME LOCK
Depending on how you set up your remote, the
VOL
and
MUTE
may control the volume only on your TV, regardless
of the position of the
MODE
switch. This remote can be set
up so that the
VOL
and
MUTE
keys work
only
with the
component selected by the
MODE
switch. To enable this
feature, perform the following steps:
1.
Press and hold the
MUTE
and
SELECT
keys until the
green light under the
DIRECTV
position flashes twice,
then release both keys.
2.
Using the number keys, enter
9-9-3
.
(The green light
will flash twice after the
3
.)
3.
Press and release the
VOL
+
key. (The green light
flashes 4 times.)
Now the
VOL
and
MUTE
keys will work
only
for the
component selected by the
MODE
switch position.
Locking Volume to AV1, AV2 or TV
1.
Slide the
MODE
switch to the
AV1
,
AV2
or
TV
position to
lock the volume.
2.
Press and hold the
MUTE
and
SELECT
keys until the
green light under the selected switch flashes twice and
release both keys.