Dell 1250C User's Guide - Page 57

Labels - printer driver

Get Dell 1250C PDF manuals and user guides View all Dell 1250C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

- Have nicked edges or bent corners - Have rough, cockle, or laid finishes Labels Your printer can print on many labels designed only for use with laser printers. When selecting labels: • Label adhesives, face sheet (printable stock), and topcoats must be able to withstand temperatures of 205 °C (401 °F) and pressure of 25 pounds per square inch (psi). • Use labels that can be without sealing, excessive curling, wrinkling, or releasing hazardous emissions. • Do not use label sheets with a slick backing material. NOTICE: Before buying large quantities of any print media, it is recommended that you try a sample first. When printing on labels: • Use labels that can withstand temperatures of 205 °C (401 °F) without sealing, excessive curling, wrinkling, or releasing hazardous emissions. • Set the paper type to Label from the printer driver. • Do not load labels together with paper in the same tray. • Do not print within 1 mm (0.04 inches) of the die-cut. • Do not print within 1 mm (0.04 inches) of the edge of the label, of the perforations, or between die-cuts of the label. • Do not print a label through the printer more than once. • Portrait orientation is preferred, especially when printing bar codes. • Do not use labels that have exposed adhesive. • Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam. • Do not use label sheets that have adhesive to the edge of the sheet. It is recommended that zone coating of the adhesive is done at least 1 mm (0.04 inches) away from edges. Adhesive material contaminates your printer and could void your warranty. Print Media Guidelines 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
Print Media Guidelines
55
–
Have nicked edges or bent corners
–
Have rough, cockle, or laid finishes
Labels
Your printer can print on many labels designed only for use with laser printers.
When selecting labels:
•
Label adhesives, face sheet (printable stock), and topcoats must be able to
withstand temperatures of 205 °C (401 °F) and pressure of 25 pounds per
square inch (psi).
•
Use labels that can be without sealing, excessive curling, wrinkling, or
releasing hazardous emissions.
•
Do not use label sheets with a slick backing material.
NOTICE:
Before buying large quantities of any print media, it is recommended that
you try a sample first.
When printing on labels:
•
Use labels that can withstand temperatures of 205 °C (401 °F) without
sealing, excessive curling, wrinkling, or releasing hazardous emissions.
•
Set the paper type to
Label
from the printer driver.
•
Do not load labels together with paper in the same tray.
•
Do not print within 1 mm (0.04 inches) of the die-cut.
•
Do not print within 1 mm (0.04 inches) of the edge of the label, of the
perforations, or between die-cuts of the label.
•
Do not print a label through the printer more than once.
•
Portrait orientation is preferred, especially when printing bar codes.
•
Do not use labels that have exposed adhesive.
•
Use full label sheets. Partial sheets may cause labels to peel off during
printing, resulting in a jam.
•
Do not use label sheets that have adhesive to the edge of the sheet. It is
recommended that zone coating of the adhesive is done at least 1 mm
(0.04 inches) away from edges. Adhesive material contaminates your
printer and could void your warranty.